TW Steel VK63 User manual

VK63
SEIKO MOVEMENT

TW STEEL
MAINTENANCE
TW Steel uses the best materials and carries out
strict controls before the watch leaves the factory.
The way in which you wear or treat your TW Steel
will determine whether the appearance of the
watch is maintained in the future, or whether it will
deteriorate. In order to enjoy wearing your TW Steel
as long as possible, we include a number of tips: If
the watch comes into contact with hard or corrosive
materials, this can cause damage, which, if it occurs
regularly, will become clearly visible in the form of
scratches.
Your watch should be cleaned with a soft cotton cloth
that is not impregnated with any cleaning material.
Absolutely no cleaning materials should be used. It
is advisable to regularly polish your watch with a soft
cotton cloth. The watch is a precision mechanical
instrument and should be treated as such. Adjusting
the time or date, opening or closing the crown or
crowncap, should not be done roughly, but carefully.
TW Steel isawatch brand harmoniously combining both design and
innovation. ‘The Watch in Steel’ leads the oversized market with style and
quality guaranteed. TW Steel values the most important relationship of all
– the onewith the consumer. To express this, wehereby give you all the
information that you need to enjoy yourTW Steel watch to the fullest.
VK63 SEIKO MOVEMENT

DISPLAY AND CROWN / BUTTONS
1) Pull out the crown to the second click position.
2) Turn the crown to set hour and minute hands.
(Check that AM / PM is set correctly.)
3) Push the crown back into the normal position.
*If the crown is pulled to the second position while the chronograph is started,
the chronograph hands will continue to move. This is not a malfunction.
HOW TO SET THE TIME
1) Pull out the crown to the first click position.
2) Turn the crown clockwise for date setting.
*Do not set the date between 9:00 P.M. and 3:00 A.M. as this will
cause a malfunction.
3) Push the crown back into the normal position.
HOW TO SET THE DATE
HOW TO RESET (AFTER BATTERY CHANGE)
HOW TO USE THE CHRONOGRAPH
2*
3*
7*
11*9*1*
*10
8*5*
6*4*
Note
*1: Hour hand*6:24 hour hand
*6: 24 hour hand
*8: Button (B) (RESET)
*2: Minute hand
Button (A) (START / STOP)
*11: Crown at second position
(Time setting)
*10: Crown at first position
(Date setting)
*4: Small second hand
*5: Chronograph minute hand
(60 minute)
*7:
*9: Crown at normal position
*3: Chronograph second hand
It is possible to reset by the following two methods.
1) Press button (A) to start the chronograph. The chronograph second
hand will start moving.
2) (6 hour 20 minutes 10 seconds)
Press button (A) again to stop the chronograph. The chronograph
hands stop to indicate the elapsed time.
3) Press button (B) to reset the the chronograph. All the chronograph
hands will be reset to "0" position.
1) Set the crown to the normal position.
2) Touch the AC terminal of circuit block and the switch
spring with conductive tweezers to reset the circuit.
3) The small second hand will move at two-second
interval for 10 seconds.
Method 1
Method 2
1) Pull out the crown to the second click position.
2) Press the button (B) for two seconds and release
the button.
3) Push the crown back into the normal position.
4) The small second hand will move at two-second
interval for 10 seconds.
*If the crown is operated within this 10 seconds, the two-second interval movement
will not activate.
**It is not necessary to set the chronograph hands after the battery is exchanged.
***If the chronograph hands position are incorrect, following below procedure all
the chronograph hands will be reset to "0" position.
*The chronograph can measure up to 60 minutes.
**The chronograph stops after a measurement for 60 minutes.
***During the chronograph operation, button (B) (reset) can be pushed. There is no
problem with the function.
Button (A)
(START)
Button (A)
(STOP)
Button (B)
(RESET)
Press the buttons in the following order: A A B