Tyco TY3201 User manual

Model TY3201 – 80 K-factor
Pendent Sprinkler
Quick Response, Standard Coverage
Page 1 of 2 AUGUST 2018 TFP179
IMPORTANT
Refer to Technical Data Sheet
TFP2300 for warnings pertaining to
regulatory and health information.
Always refer to Technical Data
Sheet TFP700 for the “INSTALLER
WARNING” that provides cautions
with respect to handling and instal-
lation of sprinkler systems and com-
ponents. Improper handling and
installation can permanently damage
a sprinkler system or its compo-
nents and cause the sprinkler to fail
to operate in a fire situation or cause
it to operate prematurely.
Worldwide
Contacts
www.tyco-fire.com
General
Description
TYCO Model TY3201 80K Quick
Response Pendent Sprinklers are
standard coverage, small frame, 3 mm
glass bulb-type spray sprinklers.
NOTICE
The Model TY3201 Quick Response
Pendent Sprinklers described herein
must be installed and maintained in
compliance with this document, as well
as with the applicable standards of the
National Fire Protection Association
(NFPA), in addition to the standards of
any other authorities having jurisdiction.
Failure to do so may impair the perfor-
mance of these devices.
The owner is responsible for main-
taining their fire protection system
and devices in proper operating con-
dition. Contact the installing contrac-
tor or product manufacturer with any
questions.
Sprinkler
Identification
Number (SIN)
TY3201 – Pendent 80K, 1/2 in. NPT
Technical
Data
Approvals
UL and C-UL Listed
FM Approved
Maximum Working Pressure
17,2 bar (UL and C-UL)
12,1 bar (FM Approvals)
Pipe Thread Connection
1/2 in. NPT
Discharge Coefficient
K=80 lpm/psi½
Temperature Ratings
68°C
Finish
Sprinkler: Chrome Plated
Physical Characteristics
Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . .Bronze
Button . . . . . . . . . . . . . . . . . . . . . . . . . . . .Bronze
Sealing Assembly ..Beryllium Nickel w/TEFLON
Bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Glass
Compression Screw . . . . . . . . . . . . . . . . .Bronze
Deflector . . . . . . . . . . . . . . . . . . . . . . . . . . .Brass
Operation
The glass bulb contains a fluid that
expands when exposed to heat. When
the rated temperature is reached, the
fluid expands sufficiently to shatter the
glass bulb, allowing the sprinkler to
activate and flow water.
Design
Criteria
TYCO Model TY3201, Quick Response,
Standard Coverage, 80K Pendent
Sprinklers are intended for fire protec-
tion systems designed in accordance
with the standard installation rules
recognized by the applicable listing
or approval agency (e.g., UL Listing is
based on the requirements of NFPA 13).

TFP179
Page 2 of 2
NATIONAL FIRE PROTECTION ASSOCIATION and NFPA are registered trademarks of National Fire Protection Association;
TEFLON is a registered trademark of DuPont
1400 Pennbrook Parkway, Lansdale, PA 19446 | Telephone [phone]
© 2018 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document revision date and are subject to change without notice.
Installation
TYCO Model TY3201, Quick Response,
Standard Coverage, 80K Pendent
Sprinklers must be installed in accor-
dance with this section.
NOTICE
Do not install any bulb type sprinkler
if the bulb is cracked or there is a loss
of liquid from the bulb. With the sprin-
kler held horizontally, a small air bubble
should be present. The diameter of the
air bubble is approximately 1,6 mm.
Install pendent sprinklers only in the
pendent orientation with the deflector
parallel to the mounting surface.
General Instructions
A leak-tight 1/2 inch NPT sprinkler joint
should be obtained with a torque of
9.5 to 19,0 N·m. Higher levels of torque
may distort the sprinkler inlet with con-
sequent leakage or impairment of the
sprinkler.
Do not attempt to compensate for
insufficient adjustment of an escutch-
eon plate by under- or over-tightening
the sprinkler. Readjust the position of
the sprinkler fitting to suit.
Step 1. After installing an escutcheon,
as applicable, over the sprinkler pipe
threads, and with pipe thread sealant
applied to the pipe threads, hand-
tighten the sprinkler into the sprinkler
fitting.
Step 2. Wrench-tighten pendent sprin-
klers using only the W-Type 6 (End A)
Sprinkler Wrench. The wrench recess
of the sprinkler wrench (Ref. Figure 2)
is to be applied to the sprinkler wrench
flats (Ref. Figure 1).
Care and
Maintenance
TYCO Model TY3201, Quick Response,
Standard Coverage, 80K Pendent
Sprinklers must be maintained and ser-
vices in accordance with this section.
Before closing a fire protection system
main control valve for maintenance
work on the fire protection system that
it controls, permission to shut down the
affected fire protection system must be
obtained from the proper authorities
and all personnel who may be affected
by this action must be notified.
Sprinklers that are found to be leaking
or exhibiting visible signs of corrosion
must be replaced.
Automatic sprinklers must never be
painted, plated, coated, or other-
wise altered after leaving the factory.
Modified sprinklers must be replaced.
Sprinklers that have been exposed to
corrosive products of combustion, but
have not operated, should be replaced
if they cannot be completely cleaned
by wiping the sprinkler with a cloth or
by brushing it with a soft bristle brush.
Care must be exercised to avoid
damage to the sprinklers before,
during, and after installation. Sprin-
klers damaged by dropping, striking,
wrench twist/slippage, or the like, must
be replaced. Also, replace any sprinkler
that has a cracked bulb or that has lost
liquid from its bulb. (Refer to Installa-
tion Section).
The owner is responsible for the
inspection, testing, and maintenance of
their fire protection system and devices
in compliance with this document, as
well as with the applicable standards
of the National Fire Protection Asso-
ciation (e.g., NFPA 25), in addition to
the standards of any other authorities
having jurisdiction. Contact the install-
ing contractor or product manufacturer
with any questions.
It is recommended that automatic
sprinkler systems be inspected, tested,
and maintained by a qualified Inspec-
tion Service in accordance with local
requirements and/or national codes.
Limited
Warranty
For warranty terms and conditions, visit
www.tyco-fire.com.
Ordering
Procedure
Contact your local distributor for avail-
ability. When placing an order, indicate
the full product name and Part Number
(P/N).
Sprinkler Assemblies with
NPT Thread Connections
Specify: Model TY3201, Quick
Response Pendent Sprinklers,
68°C, with Chrome Plated finish,
P/N 51-014-9-155
Sprinkler Wrench
Specify: W-Type 6 Sprinkler Wrench,
P/N 56-000-6-387
WRENCH RECESS
(USE END "A" FOR
MODEL TY3201)
-
2
Button
Temperature
rating is
indicated on
Deector.
Deector
Compression
Screw
Bulb
Sealing
-
6
*
-
4
5
-
3
-
*
*
6
4
5
1
3
2
Components:
Frame
1
-
1/2"
NPT
11,1 mm
MAKE-IN
NOMINAL
WRENCH
52,4 mm
FLATS
25,7 mm
Assembly
FIGURE 1
QUICK RESPONSE
MODEL TY3201 PENDENT SPRINKLER
80 K-FACTOR, 1/2 INCH NPT
FIGURE 2
W-T YPE 6
SPRINKLER WRENCH