Tysso MP-1311 User manual

MP-1311
10.1 Inch Mobile Point of System
User Manual
Installation Guide

Copyright © 2019 Fametech Inc. All Rights Reserved.
All other brands, product names, company names, trade names, trademarks and service marks used herein are
the property of their respective owners.
1
General Information
About This Manual
The purpose of this user’s manual is to provide general information on TYSSO’s POS
Terminal and to show the users how to configure the hardware-related configurations. The
information in this manual is subject to change without notice due to rapid improvement on IT
technology. Users can get the most up to date information from our web sites:
https://www.fametech.com.tw
Disclaimer
This manual has been examined for accuracy. While precaution has been taken in the
preparation of this manual, neither the manufacturer takes no liability for errors or omissions
nor assume any responsibility for damage(s) incurred directly or indirectly from errors,
omissions, or discrepancies of this manual.
IN NO EVENT WILL THE VENDOR BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF THE
POSSIBILITY OF SUCH DAMAGES HAS BEEN ADVISED. IN PARTICULAR, THE
VENDOR SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR
DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF
REPAIRING, REPLACING, OR RECOVERING SUCH HARDWARE, SOFTWARE OR
DATA.
Warning
The terminal has been tested and found to comply with the limits for a Class a digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interface in a residential installation. This equipment can generate
and radiate radio frequency energy and, if not installed and used according to the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interface will not occur under particular installation. If this equipment does cause harmful
interference to radio or television reception, which is found by turning the equipment off and
on, the user is encouraged to try to correct the interface by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the distance between the equipment or device.
Connect the equipment to an outlet other than the receiver’s.
Consult a dealer or an experienced radio/TV technician for assistance.

Copyright © 2019 Fametech Inc. All Rights Reserved.
All other brands, product names, company names, trade names, trademarks and service marks used herein are
the property of their respective owners.
2
Caution
The system is provided with a battery-powered Real-Time Clock circuit. There is a danger of
exposing and personal injury if the battery is incorrectly replaced or mistreated. Do not
attempt to disassemble the battery, immerse it in the water or expose it to fire.
MP-1311 is required to be charged over 8 hours when used for the first time.
Warranty Limits
If the product and the parts are disassembled by any person other than the authorized
technicians, the warranty will be terminated. The users should consult his/her dealer for any
technical problems. Warranty does not cover any damage caused by improper use.
Trade Marks and Service Marks
TYSSO is a registered trademark of FAMETECH INC.
Other brand and product names are trademarks and registered trademarks and service marks
of their respective owners.

Copyright © 2019 Fametech Inc. All Rights Reserved.
All other brands, product names, company names, trade names, trademarks and service marks used herein are
the property of their respective owners.
3
Important Safety Information
Read following instructions carefully.
Use only parts, especially power adapter, recommended by the manufacturer;
unapproved parts may be hazardous.
Before plugging the power cord into the AC inlet of the power supply unit, make sure
that the voltage applied to the power outlet is within the specified range (100V~240V).
Improper power source voltage range will cause damage to the power supply unit.
Power off the system and remove the power adapter while cleaning the system.
Before powering on the system, make sure all the peripherals are firmly installed.
Do not use the system near water, such as a bathtub, a washbowl, a kitchen sink, a
laundry tub, and a swimming pool. Do not expose the machine under direct sunlight, and
keep it away from any heat source.
Do not place the system on an unstable cart, stand or table. If the machine falls, it may
injure a person or cause serious damage to the appliance.
The system is equipped with a three-wire grounded plug with a third (grounding) pin.
This is a safety feature. If your outlet does not accommodate the three-wire plug, have an
electrician install a correct outlet, or use an adapter to ground the appliance safely. Do
not leave out the safety purpose of the grounded plug.
Do not allow anything to rest on the power cord. Do not locate the system where people
may walk on the cord.
Do not make the power outlet and extension cords overload. Overload can result in fire
or electric shock.
Do not push any object into the computer cabinet. Dangerous voltage points may be
touched and the parts may be shorted out resulting in fire or electric shock.
Do not attempt to service the system on your own. Opening or removing cover can
expose you to dangerous voltage or other hazards.
Power off the system before installing or removing non-PNP (plug and play) devices.
If any of the following situations occurs, unplug the systems from the power outlet
immediately and consult with a qualified service person:
1. The power cord or plug is damaged or frayed.
2. Liquid is spilled into the system.
3. The system is dropped or the cabinet is damaged.
When the system is not in use, cover the system and store it with care.

Copyright © 2019 Fametech Inc. All Rights Reserved.
All other brands, product names, company names, trade names, trademarks and service marks used herein are
the property of their respective owners.
4
Contents
General Information 1
About This Manual 1
Disclaimer 1
Warning 1
Caution 2
Warranty Limits 2
Trade Marks and Service Marks 2
Important Safety Information 3
Product Overview 5
Packing 5
Specifications 6
Parts Descriptions 10
MPOS Installation 15
Charge Your Tablet 15
1. AC Power Adapter via Main Tablet 15
2. Main Tablet via Charging Cradle 16
Start Your POS system 17
Replace the External Module Sku 18
Note: Plastic Protective Cap (CB-1300-G) 19
Install Micro SD Card in MP-1311 20
Detach the Hand Strap 21

Copyright © 2019 Fametech Inc. All Rights Reserved.
All other brands, product names, company names, trade names, trademarks and service marks used herein are
the property of their respective owners.
5
Product Overview
Packing
Main Tablet with External Module Sku
Main Tablet x 1
Quick Installation Guide x 1
External Module Skus*
Module A: MSR, 2D Barcode Scanner, and Finger Print.
Module B: MSR, 2D Barcode Scanner, and NFC.
Module C: MSR and 2D Barcode Scanner.
Module E: 2D Barcode Scanner.
Module F: MSR.
Optional Peripherals
Dock Station (CB-1300-C)
Dock Station (CB-1300-D)
Charging Cradle (CB-1300-E)
Tablet Power Adapter
COM RJ45 Cable
Hand Strap
* The External Module Skus (Modules A, B, C, E, and F) is optional and pre-installed to the Main Tablet.
For more information relating to the External Module Skus, please contact the local representatives or technical
support personnel of the providers.

Copyright © 2019 Fametech Inc. All Rights Reserved.
All other brands, product names, company names, trade names, trademarks and service marks used herein are
the property of their respective owners.
6
Specifications
Model Description
MP-1311-A
MP-1311-B
MP-1311-C
MP-1311-E
MP-1311-F
Main System
Processor
Intel Atom® x5-Z8350 Quad Core 1.44GHz, up to 1.92GHz
Display
10.1-inch IPS, 1280 x 800, 300nits
Touch Panel
True-Flat Projected-Capacitive Multi Touch (PCAP)
Memory
4GB DDR3L 1600MHz
Storage
64GB eMMC
Micro-SD Slot
Up to 128GB
Communication
Wi-Fi IEEE 802.11 b/g/n, Bluetooth 4.0 and GPS
Webcam
2M Front Camera (FF) and 5M Rear Camera (AF)
Speaker
2 x 0.8W Speakers
Sensor
Light Sensor, G Sensor and Gyroscope
I/O Interface
USB
1 x USB 3.0 TypeA
Po-go Pin
1 x Pogo Pin (for charging and data transmission)
Peripherals
External Modules
MSR
MSR
MSR
N/A
MSR
2D Barcode
Scanner
2D Barcode
Scanner
2D Barcode
Scanner
2D Barcode
Scanner
N/A
Finger Print
N/A
N/A
N/A
N/A
N/A
NFC
N/A
N/A
N/A
Power Management
Internal Battery
Lithium Polymer Battery 4800mAh
PowerAdapter
5V@3A 15WAC Power Adapter (option)

Copyright © 2019 Fametech Inc. All Rights Reserved.
All other brands, product names, company names, trade names, trademarks and service marks used herein are
the property of their respective owners.
7
Mechanical & Environmental
Dimension
Main Tablet : 310 (W) x 187.2 (H) x 25.9 (D) mm
Dock Station : 220.5 (W) x 160.8 (H) x 125.8 (D) mm
Weight
Main Tablet : 0.95kg (w/o accessories)
Dock Station : 1.23kg (w/o power adapter)
Operation System
Windows 10 IoT Ent LTSB Entry EPKEA
Certification
CE / FCC Class B
Operation Condition
0°C to +40°C / 10 to 85% without condensation
Charging Condition
0°C to +40°C / 10 to 85% without condensation
Storage Condition
-10°C to +50°C / 10 to 85% without condensation
* The product information and specifications are subject to change without prior notice.
To get the detailed information on the MP-1311, please check this model from Tysso Website.

Copyright © 2019 Fametech Inc. All Rights Reserved.
All other brands, product names, company names, trade names, trademarks and service marks used herein are
the property of their respective owners.
8
Optional Accessories
Dock Station
(CB-1300-C)
2 x USB 2.0, 1 x COM (DB9), 1 x LAN, 1 x DC-in and 1 x Pogo Pin (for
charging and data transmission)
12V@2A 24W AC Power Adapter
Dock Station
(CB-1300-D)
3 x USB, 2 x COM (RJ45, w/0/5V/12V), 1 x LAN, 1 x DC-in and 1 x
Pogo Pin (for charging and data transmission)
12V@3A 36W AC Power Adapter
Charging Cradle
(CB-1300-E)
I/O Connectors : 1 x DC-in and 1 x Pogo Pin (for charging)
12V@2A 24W AC Power Adapter
Tablet Power Adapter
5V@3A 15W AC Power Adapter
Cable
RJ45 to DB9 Cable (50cm)
Hand Strap
Design to securely hold the MP-1311-X Series Tablet
Note:
The specifications are subjected to change without prior notice.
For further information relating to the optional accessories, please contact the local representatives or technical
support personnel of the providers.

Copyright © 2019 Fametech Inc. All Rights Reserved.
All other brands, product names, company names, trade names, trademarks and service marks used herein are
the property of their respective owners.
9
Dimensions
Top View
Left View Front View Right View
Bottom View
Rear View

Copyright © 2019 Fametech Inc. All Rights Reserved.
All other brands, product names, company names, trade names, trademarks and service marks used herein are
the property of their respective owners.
10
Parts Descriptions
Front View
Light
Sensor
LED
Indicator
Front Camera
Alignment
Mark
Light
Sensor
LED
Indicator
Front Camera
Alignment
Mark
Volume
(Up / Down)
Power
Button
MSR
Finger Print
External
Module Sku*
LCD
Touch Screen
LCD
Touch Screen
MSR
NFC
External
Module Sku*
Volume
(Up / Down)
Power
Button
USB 2.0
USB 2.0

Copyright © 2019 Fametech Inc. All Rights Reserved.
All other brands, product names, company names, trade names, trademarks and service marks used herein are
the property of their respective owners.
11
Rear View
Note:
The External Module Skus (Modules A, B, C, E, and F) is optional and pre-installed to the
Main Tablet.
Bottom View
Pogo Pin
(to Dock Station and Charging Cradle)
2D Barcode
Scanner
Rear Camera
Hand Strap
Scan Trigger
External
Module Sku*

Copyright © 2019 Fametech Inc. All Rights Reserved.
All other brands, product names, company names, trade names, trademarks and service marks used herein are
the property of their respective owners.
12
Side View
Turn off MP-1311 completely before installing the Micro SD card.
5VDC
Input
Left View
Right View
(with External Module Sku)
Right View
(with Plastic Protective Cap)
Micro SD Slot (TF)
Micro USB
HDMI
USB 3.0
Main Tablet
(Rear View)

Copyright © 2019 Fametech Inc. All Rights Reserved.
All other brands, product names, company names, trade names, trademarks and service marks used herein are
the property of their respective owners.
13
External Module Skus
Detached Main Tablet (Left) and External Module Sku (Right)
NFC
Module A
MSR
2D Barcode Scanner
Finger Print
Module B
MSR
2D Barcode Scanner
NFC
Module C
MSR
2D Barcode Scanner
Module E
2D Barcode Scanner
Module F
MSR

Copyright © 2019 Fametech Inc. All Rights Reserved.
All other brands, product names, company names, trade names, trademarks and service marks used herein are
the property of their respective owners.
14
Dock Station (CB-1300-C)
Dock Station (CB-1300-D)
Charging Cradle (CB-1300-E)
DC IN COM1 USB LAN
12VDC
Input
DC IN LAN USB COM2 COM1

Copyright © 2019 Fametech Inc. All Rights Reserved.
All other brands, product names, company names, trade names, trademarks and service marks used herein are
the property of their respective owners.
15
MPOS Installation
Charge Your Tablet
1. AC PowerAdapter via Main Tablet
①.Connect the connector of the AC power adapter to the Main Tablet.
②.Plug the AC power adapter into an electrical outlet.
③.The LED Indicator indicated that the Main Tablet is start charging process.
(Battery Charging < 100%: Orange; Battery Fully: Green)
5VDC
Input
Main Tablet
AC PowerAdapter

Copyright © 2019 Fametech Inc. All Rights Reserved.
All other brands, product names, company names, trade names, trademarks and service marks used herein are
the property of their respective owners.
16
2. Main Tablet via Charging Cradle
①.Connect the connector of the AC power adapter to the Dock Station or Charging Cradle.
②.Plug the AC power adapter into an electrical outlet.
③.Install the Main Tablet to the Dock Station or Charging Cradle.
④.The LED Indicator indicated that the Main Tablet is start charging process.
(Battery Charging < 100%: Orange; Battery Fully: Green)
Tips:Alignment Mark
The Alignment Mark helps you to install the Main Tablet to the Dock Station (or Charging
Cradle).
Main Tablet
Dock Station
Or
Charging
Cradle
12V DC
Input
AC PowerAdapter
Alignment Mark
(Main Tablet)
Alignment Mark
(Dock Station or Charging Cradle)

Copyright © 2019 Fametech Inc. All Rights Reserved.
All other brands, product names, company names, trade names, trademarks and service marks used herein are
the property of their respective owners.
17
Start Your POS system
To Start the System:
Press the Power Button for 3 seconds until the system is initiated.
There is an audio notification and the system is initiated.
To Shut Down the System:
Use the system menu to shut down the system.
Forced Shut Down:
In the system has no response, press the Power Button for 10 seconds to shut down the system.
Re-start the system again and examine the system functionality.
Pres
Power
BEEP
3 Sec
10 Sec

Copyright © 2019 Fametech Inc. All Rights Reserved.
All other brands, product names, company names, trade names, trademarks and service marks used herein are
the property of their respective owners.
18
Replace the External Module Sku
To replace or detach the External Module Sku:
1. Turn off the Tablet System.
2. Remove the securing screws of the External Module Sku.
Rear View of Main Tablet with External Module Sku
3. Detach the External Module Sku form the Main Tablet.
4. Install a new External Module Sku to the Main Tablet.
Secure the securing screws back to the Main Tablet.
Securing Screw
Securing Screw

Copyright © 2019 Fametech Inc. All Rights Reserved.
All other brands, product names, company names, trade names, trademarks and service marks used herein are
the property of their respective owners.
19
Note: Plastic Protective Cap (CB-1300-G)
If the is no External Module Sku installed on the Main Tablet.
Please use the supplied Plastic Protective Cap (MP-1300-F) and install to the Main Tablet.
Tablet
Plastic Protective Cap