Tysso VFD-450 Series User manual

VFD-450/550 Series
VFD Customer Display
User's Manual

-1-
Contents
1. Information
2. Installation
3. Interfaces
5. Specifications
2
3
4
.............................................................
A. Standard Package................................................ 2
B. Optional Accessories........................................... 2
...............................................................
.................................................................
............................................ 7
.......................................................... 14
................................................. 16
7 .............................. 22
........................... 25
Mode 0 VFD-450/550............................................. 25
Mode 1 EPSON Esc/POS........................................ 26
Mode 2 UTC Standard............................................ 27
Mode 3 UTC Enhanced.......................................... 28
Mode 4 AEDEX...................................................... 28
Mode 5 ICD 2002................................................... 29
Mode 6 CD 5220.................................................... 31
Mode 7 DSP-800.................................................... 33
Mode 8 ADM 787/788............................................ 34
4. Character Fonts Table
6. System Commands
. VFD Function Demo Software
Appendix: Select Command Modes

VFD Customer Display
Model VFD Series
2. Installation (RS-232 Interface)
1.Information
A. Standard Package:
B. Optional Accessories:
1. Display Unit 1 PC
2. User's Manual 1 PC
3. Demo Software and Utility Diskette 2 PCS
4. Power Kit 1 PC
to retrieve power 12 VDC from switching power
supply inside computer
1. Switch-Mode Power Supply:
Input: 100V AC~240V AC, 50Hz~60Hz
Output: DC 9V, 1.33A
2. Y-connection cable: for printer pass-through connection
3. Option Pole/Base:
a. DSP-B01: Long pole with small round base
b. DSP-B02: Metal base (should be used with DSP-B01)
c. DSP-B03: Short pole with square base
d. DSP-B04: Side wall mounting brocket (used with
DSP-B01)
4. Option Double Sides Display:
a. VFD-488: Double sides VFD Display
b. VFD-455: Front VFD with Back LCD Display
Step 1: Turn the computer system power off.
Step 2: Connect the Display Cable to the RS-232 Port of
the computer.
Step 3: Connect the DC power source by the appropriate
DC power adapter.
Step 4: Turn on the computer and the power supply unit,
the display will be on and ready for receiving data.
-3--2-
To RS-232 port
AC power
Source
Extension
RS-232 Cable

-4- -5-
3. Pass-through Connection
All the data transmitted from the host will be processed,
and if it is for the printer, it will be transmitted to the printer.
Whether the data is for the display or the printer can be
switched using the peripheral device selection command.
To Display To Printer From Host
TXD 1-------------------------------------- 2
RXD 2-------------------------------------- 3
VCC 3--------------------------------------------------- (INNER)
GND 4-------------------5----------------- 5---------- (Outer)
FROM NEXT 5-------------------2
TO NEXT 6-------------------3
1+4+6 (SHORT)
7+8 (SHORT)
RJ45(8P8C) JACK DB9M DB9F+DC JACK
Transmit data from host
Interface conversion
Transmit data from printer
data for printer
18
To Display
RJ45 JACK
From Host
DB9F+DC
To Printer
DB9M
For pass-through connection, the RS-232 cable should
be replaced by the pass-through cable.
1. RS-232 Cable-end
2. DC Power Jack
3. Interfaces (Cable Connections)
DSUB-9F Connector
2
3
5
7
8
9
1
4
6
TX
RX
GND
CTS
RTS
VCC
Short Connection
GND 9~12VDC/1000~1500 mA
RS-232
Cable
Pass-Through
Cable
RJ-45 Female Connector
RJ-45 Male Connector
RJ-45 Female Connector
7 pin Male-Header
Connect to Display Panel Side
DB9M, to Printer
DB9F+DC Jack, to Host
Display
Main Cable
(Inside the Pole)
Connect to Host
DB9 Female with DC Jack

4. Character Fonts Table
-7-
-6-
4.1 Control code set
4. Interface of Display Panel Side
- Specifications
- Interface connector
Data transmission method : Asynchronous Serial.
Default protocol : 9600 bps, non-parity,
8 data bits, 1 stop bit.
(display panel side)
7 pin Male-Header
Pin assignments:
1
7
TXD
DSR
RXD
DTR
GND
GND
VCC
4.2 U.S.A. font set

3DH: Standard Europe international font set
3EH: Multingual international font set
4.3 International character selection
-9-
-8-
Hex. Value
-8-

41H: NORDIC internatinal font set
42H: RUSSIA font set
3FH: Portuguese international font set
40H: Canadian French international font set
-11-
-10-

43H: SLAVONIC Font set
44H: Katakana font set
-13-
-12-

-15--14-
5. Specifications:
D. Overall Dimensions:
E. Electricity
•
•
•
•
•
•
•
•
•
•
•
Dimension (panel) 110mm H x 220 mm L x 45 mm D
Dimension (support) Telescopic pole from 270
to 440 mm
Dimension (base) 12 mm Height with 80mm OD
Viewing angle Max. 45
Horizontal rotation Max. 360
Weight About 0.8 Kg
Power source DC +9V~12V (Optional +5V, +24V)
Power consumption 4.5 watts for single side display
8.0 watts for double sides display
Central control unit CPU 8031 BH
ROM 64K flash ROM
RAM 32K SRAM
Speed 29 MHz
Connector 8 pins phone jack, D-SUB 9,
or 25 pins connector
o
o
A. Tube Display:
B.Environment:
C. Driver Interface:
VFD Display
•
•
•
•
•
•
•
•
•
•
•
•
Customer display Vacuum Fluorescent Display
Display pattern 5 x 7 dot matrix
Brightness 700 cd/m
Character type 96 Alphanumeric & 13 Kinds
of international character set
and user definable character
set.
Character size 6.4mm (W) x 9.2mm(H)
Character number 20 x 2(40 characters) /
20 x 2x 2(80 characters)
Character font 5x7 dots matrix, comma,
decimal point
Driver interface RS-232
Driver command ESC commands
2
Operating temperature 0 C to +40 C
Storage temperature -10 C to +50 C
Relative humidity 0% to 90% RH
oo
oo

-17-
-16-
6.2.2. Select international code table
6.2.3. Save the current view message
COMMAND: I
COMPUTER:EOT SOH 'I' 'CHAR' ETB
ASCII(04H)(01H)(49H)(30H~44H)(17H)
Byte 1 1 1 1 1
DISPLAY: ACK (or NACK if failed)
ASCII (06H) (15H)
Byte 1 1
Note : International Character Code
Please refer to 4.3 International Character Selection.
(Save Demo view data)
COMMAND: S
COMPUTER:EOT SOH 'S' 'Layer' ETB
ASCII(04H)(01H)(53H)(31H~33H)(17H)
Byte 1 1 1 1 1
DISPLAY: ACK (or NACK if failed)
ASCII (06H) (15H)
Byte 1 1
Note : 31H: Layer 1 / 32H: Layer 2 / 33H: Layer 3
6. System Commands
6.1. Command format
6.2. Commands list
EOT SOH COMMAND ETB
6.2.1. Set Baud Rate
COMMAND: B
COMPUTER:EOT SOH 'B' 'BAUD RATE' 'N' ETB
ASCII (04H) (01H)(42H) (31H~37H) (4EH)(17H)
Byte 1 1 1 1 1 1
DISPLAY: ACK (or NACK if failed)
ASCII (06H) (15H)
Byte 1 1
Note: Baud rates
31H : 9600
32H : 4800
33H : 2400
34H : 1200
35H : 600
36H : 300
37H :19200
End of Transmission Block
(17 Hex)
See Command list
Start of Heading
(01 Hex)
(04 Hex)
30H :
31H :
32H :
33H :
34H :
35H :
36H :
37H :
38H :
39H :
3AH :
U. S. A.
France
Germany
U. K.
Denmark I
Sweden
Italian
Spain
Japan
Norway
Denmark II
3BH :
3CH :
3DH :
3EH :
3FH :
40H :
41H :
42H :
43H :
44H :
Slavonic
Russia
Standard Europe International font set
Multingual International font set
Portuguese International font set
Canadian French International font set
Nordic International font set
Russia font set
Slavonic font set
Katakana font set