U-Line H-1227 User manual

PAGE 1 OF 4 1012 IH-1227
H-1227
H-3637
SINGLE TIER
LOCKER
1-800-295-5510
uline.com
π
TOOLS NEEDED
11/32" Nut Driver
(included)
CAUTION! Some parts may have sharp
edges. Take care when handling various
pieces to avoid injury. For your safety, wear
work gloves when assembling.

PAGE 2 OF 4 1012 IH-1227
RTS
2
10
3
5
4
8
9
6
1
7
13
14
18
17
16
14
20
19
11
12
15
PARTS
#DESCRIPTION QTY.
1Back 3
2Left Side 2
3 Rear Leg 4
4Shelf 3
5Coat Hook 6
6Top/Bottom 6
7Right Side 2
8 Door Frame Assembly 3
9Locker Door 3
10 Coat Rod (For H-1227 only) 3
#DESCRIPTION QTY.
11 Number Plate 3
12 Plush Plug 6
13 Latch And Spring 9
14 Bumper 6
15 Dart Clip 6
16 Locking Channel 3
17 Lock Receiver 3
18 Reinforcement Tab 3
19 Recessed Handle 3
20 Logo Plate 3
PRIMARY ASSEMBLY NO ASSEMBLY REQUIRED

PAGE 3 OF 4 1012 IH-1227
ASSEMBLY INSTRUCTIONS
ASSEMBLING MAIN PANELS
NOTE: Do not tighten bolts until unit is
completely assembled.
1. Locate and separate the left and righthand sides
(2 & 7). Identify the top of each panel. The top of
each panel has three holes instead of one.
2. Place back (1) on a protected flat surface so that
the flanges face upward.
3. Bolt left side (2) to the back (1) so that side flange
fits around back (use 7 bolts and nuts - nuts to the
inside). Do not use bottom 2 holes; these will be
used for attaching legs in step 8. (See Figure 1)
4. Attach top and bottom (6) to side (2) and back (1) as
shown (See Figure 2). Bolt shelf (4) to back and side.
NOTE: Save one right side for step 7.
5. Bolt an intermediate side and back panel to the
flange of the first locker (use 7 bolts and nuts - as in
step 3). Bolt shelf (4) to back and side. Attach top
and bottom (6) to the first intermediate side and
back panel.
NOTE: A left or right side may be used as
an intermediate side.
6. Next attach remaining intermediate side and back
to flange of second back. Then attach remaining
shelf, top and bottom to the intermediate side.
7. Bolt right side (7) to the back so that side flange fits
around back. Attach side to top, bottom and shelf.
(See Figure 3)
8. Attach coat hooks (5) to each locker’s left side and
back panel:
•Side – 3rd & 4th holes below shelf (6th, 7th holes
down from top).
•Back – 2nd & 3rd holes below shelf (5th, 6th holes
down from top). (See Figure 2)
1
1
2
Figure 1
6
5
2
6
1
4
Figure 2
7
Figure 3

PAGE 4 OF 4 1012 IH-1227
πCHICAGO•ATLANTA•DALLAS•LOSANGELES•MINNEAPOLIS•NYC/PHILA•SEATTLE•MEXICO•CANADA
1-800-295-5510
uline.com
ASSEMBLY INSTRUCTIONS CONTINUED
3
3
Figure 4
9
8
Figure 5
Figure 6
9. Insert the legs (3) into corners between the bottom
and the side. Bolt the leg to the side using two bolts
and nuts per leg. (See Figure 4)
10. Place door and frame assembly (8 & 9) over the
locker body. Make certain the body sides are
inside the frame and not between the frames.
Attach top to frame header and bottom to frame
sill (one bolt each). Finish by attaching the door
and frame assembly to the sides of the locker
body (bolts will be shared with the door and frame
on either side of them). (See Figure 5) If joining a
3-wide unit beside another unit see JOINING UNITS
TOGETHER below.
11. Stand unit upright, and place in desired location.
If joining units together, remove temporary bolts in
frames and bolt adjacent units together through
frames. Check and tighten all permanent bolts.
(See Figure 6)
NOTE: If the temporary bolts are not removed
before the frames are joined side by side, the
frames will have a 1/8" gap between them.
12. For H-1227: Place non-slotted end of coat rod (10)
over projecting tab of top left coat hook. Slide the
slotted end of the coat rod over the projecting tab
in the right coat hook and turn 90˚ to secure it.
JOINING UNITS TOGETHER
1. If joining a 3-wide unit beside another unit,
temporarily install a bolt and nut into the third and
sixth holes down from the top of the outer frame(s)
that will be joined to the adjacent locker frame(s).
(See Figure 6) The center locker frame can be
bolted complete.
SECURING UNITS
1. Anchor units to wall or floor. Units are not intended
to stand free and may topple if not secured. (Units
standing back to back should be bolted together.)
CAUTION! Care must be taken to assure
that lockers are set plumb and true before
anchoring.
2. If units are not pre-numbered, an optional number
plate (11) may be attached with two #6 x 5/16 drive
screws or push plugs (12).