U-Line H-8277 User manual

PAGE 1 OF 9 0721 IH-8277
1-800-295-5510
uline.com
24/7 CHAIR
H-8277
Para Español, vea páginas 4-6.
Pour le français, consulter les pages 7-9.
1. Insert casters into legs of five-star base. Turn base
upright. Insert gas lift into center of base and place
dust cover over gas lift. (See Figure 1)
PARTS
ASSEMBLY
Figure 1
Dust Cover
Gas Lift
Screw x 3
5/16 x 7/8"
5-Star Base x 1
Dust Cover x 1 Armrest x 2
Seat Cushion x 1
Gas Lift x 1
Caster x 5
Back Support x 1
TOOL NEEDED
Allen Wrench
(included)

PAGE 2 OF 9 0721 IH-8277
Figure 4
ASSEMBLY CONTINUED
2. Slide armrest into corresponding socket on bottom
of seat cushion. Push lever in toward armrest to lock.
Repeat on opposite side. (See Figure 2)
3. Position back support in slot between bottom of
seat cushion and mechanism. Align holes and use
three 5/16 x 7/8" screws to attach back support to
mechanism. (See Figure 3)
NOTE: Use Allen wrench to tighten all screws.
4. Slowly lower chair assembly onto the gas lift.
Press down on seat cushion to secure in place.
(See Figure 4)
Figure 3
Figure 2
Armrest
Lever
Back Support
Seat Cushion

PAGE 3 OF 9 0721 IH-8277
CHAIR ADJUSTMENTS
1. Seat Height Adjustment –To raise seat height, lift
lever up with little to no weight on the seat. To lower
seat height, lift lever up while sitting.
2. Back Height –To raise back, lift back support until it
clicks into desired height. To lower, lift back support
to its tallest height to release ratchet mechanism,
then lower it to lowest height.
3. Back Angle –To tilt the back, lift the lever and move
freely. To lock tilt position push lever down while
sitting at preferred angle.
4. Adjustable Lumbar Support –To adjust lumbar
support, slide up or down.
5. Adjustable Tilt Lock –To lock seat/back angle, press
lever down at desired angle. Chair has standard tilt;
the seat and back tilt simultaneously at the same
ratio.
6. Tilt Tension –To increase tilt tension, turn knob
clockwise. To decrease tilt tension, turn knob
counterclockwise.
7. Seat Depth (Seat Slider) –To adjust seat depth, lift
the lever and slide the seat forward or back while
sitting.
8. Armrest Adjustment:
Height – To adjust arm height, press the button
under each armrest and move the armrest up
or down.
Width – To adjust arm width, pull lever away from
armrest and move the armrest in or out. Push lever
in toward armrest to lock.
1
6
8
2
5
3
6
1
5
3
4
7
1
-800-295-551
0
uline.com

PAGE 4 OF 9 0721 IH-8277
800-295-5510
uline.mx
H-8277
SILLA 24/7
1. Inserte las ruedas en las patas de la base estrella.
Enderece la base. Inserte el pistón de gas en la
base y coloque la cubierta para polvo sobre este.
(Vea Diagrama 1)
PARTES
ENSAMBLE
Diagrama 1
Cubierta
para Polvo
Pistón de Gas
3 Tornillos
5/16 x 7/8"
1 Base Estrella
1 Cubierta para Polvo 2 Descansabrazos
1 Asiento
1 Pistón de Gas
5 Ruedas
1 Respaldo
HERRAMIENTA NECESARIA
Llave Allen
(incluida)

PAGE 5 OF 9 0721 IH-8277
Diagrama 4
CONTINUACIÓN DEL ENSAMBLE
2. Deslice el descansabrazos en el soporte
correspondiente en la parte inferior del asiento.
Empuje la palanca hacia adentro y hacia el
descansabrazos para bloquearlo. Repita con el
lateral opuesto (Vea Diagrama 2)
3. Posicione el respaldo en la ranura que está entre la
parte inferior del asiento y el mecanismo. Alinee los
orificios y utilice tres tornillos de 5/16 x 7/8" para fijar
el respaldo al mecanismo. (Vea Diagrama 3)
NOTA: Utilice la llave Allen para apretar todos
los tornillos.
4. Baje lentamente el ensamble de la silla sobre el
pistón de gas. Presione el asiento para asegurarlo
en su lugar. (Vea Diagrama 4)
Diagrama 3
Diagrama 2
Descansabrazos
Palanca
Respaldo
Asiento