U-Line H-3745 User manual

1212 IH-3745PAGE 1 OF 2
1. Lay three aluminum planks side by side, upside
down, on a flat surface to form the tabletop. Slide
the metal caps onto each end. One end cap
covers the three planks. The pre-drilled holes of the
end cap should be facing up. Use the power drill
and two self-tapping
screws to secure
each metal end
cap onto each
end of the tabletop.
Loosely attach the
center support brace,
centered, onto the
middle tabletop plank
using two hold-down
clips, two 5/16" flange
nuts and two 5/16"
carriage bolts.
(See Figure 1)
2. For the seats lay two aluminum
planks upside down on a flat
surface. Slide the plastic end caps
onto each end of the planks. The
pre-drilled holes of the end cap
should be facing up. Use a power
drill and two self-tapping screws to
secure each end cap onto each
end of the plank.
(See Figure 2)
3. Loosely attach both
diagonal braces to
both leg frames using
one 3/8" flange nut
and one 3/8" hex head
bolt per leg frame.
(See Figure 3)
Diagonal
Brace
Center Support Brace
Metal End Cap
Hold Down Clip
H-3745
H-3747
ALUMINUM
OUTDOOR TABLE
1-800-295-5510
uline.com
π
TOOLS NEEDED
Power Drill Socket Wrench
PARTS
ASSEMBLY INSTRUCTIONS
Aluminum Plank x 5
Metal End Caps for Tabletop x 2
Hold Down Clips x 22
Diagonal Brace x 2
3/16" Self-Tapping
Screws x 12
Center Support Brace x 1
Leg Frame x 2
3/8" Flange Nuts x 3
5/16" Flange Nuts x 22
Figure 2
Figure 1
5/16" x 1½" Carriage Bolts x 22 3/8” x 1⁄" Hex Head Bolts x 3
Plastic End Caps for Seats x 4
Figure 3

1212 IH-3745PAGE 2 OF 2
4. Place the legs upside down onto the underside
of the tabletop. Loosely connect both diagonal
braces simultaneously to the center support brace
using one 3/8" flange nut and one 3/8" hex head
bolt. Loosely fasten each leg frame at a time to the
tabletop using six hold down clips, six 5/16" flange
nuts and six 5/16" carriage bolts per leg. The leg
frames should be 3" from the end of the tabletop.
(See Figures 4-6)
NOTE: Additional assistance may be needed to
hold up leg frames while the diagonal braces
are attached.
5. Flip the table right side up. Make sure the leg frames
are evenly aligned with the correct overhang and
the table is level. Tighten the bolts using a socket
wrench.
CAUTION! Due to weight of table, seek
assistance to turn table right side up.
6. Place the seat planks onto the frame, making sure
the edges of tabletop are flush with the edges of
the seat planks. Use four hold down clips, four 5/16"
carriage bolts and four 5/16" flange nuts per seat to
secure onto frame. (See Figures 7-8)
NOTE: H-3748 mounting hardware sold
separately.
NOTE: If the material is to be stored in a
location where moisture is a possibility, the
planks should be unbundled and stacked so
that surfaces are not touching. This will prevent
galvanic reaction from occurring or stains
from paper or cardboard packaging should
the planks get wet. Once the picnic table has
been assembled, the problem no longer exists.
ASSEMBLY CONTINUED
Figure 8
Figure 7
π CHICAGO • ATLANTA • DALLAS • LOS ANGELES • MINNEAPOLIS • NYC/PHILA • SEATTLE • MEXICO • CANADA
1-800-295-5510
uline.com
Figure 4 Figure 5
Figure 6