U-Line H-3533 User manual

PAGE 1 OF 3 0812 IH-3533
πH-3533
KIHLBERG JK35T-590
WIDE CROWN
PNEUMATIC PLIER STAPLER
1-800-295-5510
uline.com
OPERATION
LOADING THE MAGAZINE
1. Pull the pusher all the way back until it snaps in
around the parking button. Feed in a staple strip
from above into the magazine and push it forward
by hand. (See Figure 1)
2. Release the pusher by pressing the parking button.
(See Figure 2)
USING THE STAPLER
WARNING! Be sure that the stapler nozzle is
not pointed at yourself or anyone else when
connecting it to the compressed air line.
1. Adjust the air pressure to the lowest one that
will drive staples to the desired depth. Start at
approximately 5.5 bar and raise this by 0.5 bar
increments until the correct operating pressure for
the job is found.
CAUTION! Never exceed 7 bar air pressure.
A low air pressure will reduce maintenance
costs!
2. This stapler has only single shot firing without safety
yoke.
a. First place the stapler around the work piece.
b. Then pull the trigger.
NOTE: During operation, the plier's gap is fixed
but it can be set to accommodate different
material widths by means of spacers 3 and
6mm thick underneath the tongue. These are
delivered with the stapler as a set of longer
screws to be used when spacers of more than
3mm total are inserted.
Figure 2
Pusher
Parking
Button
Figure 1

PAGE 2 OF 3 0812 IH-3533
OPERATION CONTINUED
TO EMPTY THE MAGAZINE
1. Pull the pusher all the way back until it snaps in
around the parking button. (See Figure 3)
2. Take the staples out and release the pusher by
pressing the parking button. (See Figure 4)
REMOVING STUCK STAPLES
1. Park the staple pusher in its rear position. Just loosen
the 2 screws (a) holding the front plate and move
the plate downward to remove. Remove any staple
remnants. Remount the parts in the reverse order
and release the pusher. (See Figures 5 and 6)
Figure 5
a a
Figure 6
SAFETY WARNINGS
NOTE: Read these warnings to prevent injuries
to yourself and those around you.
• Never use oxygen, combustible gases, CO2, steam
or high pressure gas tanks as power sources. The
stapler may explode and cause serious injury.
• Use only dry, clean pressure-regulated compressed
air to drive the stapler.
• Eye protection must be worn by the operator and
others in the work area.
• Always use personal protection equipment as
required, such as ear protection, hard hats, etc.
• Never use a defective stapler. Ensure the trigger
operates properly and all screws and nuts are
secured tightly at all times.
• Do not modify the stapler.
• Always disconnect the stapler from the air supply
and empty the magazine when taking a break
or ending work, when servicing the stapler or
eliminating malfunctions.
• Never leave a loaded stapler unattended.
• Always assume that the stapler is loaded. No
horseplay! Respect the stapler as a working
implement.
Figure 3
Figure 4

PAGE 3 OF 3 0812 IH-3533
MAINTENANCE
SPECIFICATIONS
• Always disconnect the stapler from the air supply,
empty the magazine and read the safety warnings
before starting maintenance.
• Check daily that all safety devices function properly,
especially that the trigger moves freely and that all
screws and nuts are securely tightened.
• This stapler does not require any special servicing.
It only needs regular cleaning with a non-corrosive
cleaning agent. Do not remove any parts for
cleaning purposes!
• Check that the stapler is properly lubricated.
The stapler must be lubricated by an oil mist.
A silicon-based grease is recommended.
MFG. PART NO. HEIGHT LENGTH WIDTH WEIGHT STAPLES LENGTH MAGAZINE
CAPACITY
JK35T590 220mm 335mm 65mm 2,65kg 590 19-32mm 100
• Air pressure:
– Approx. 5-6 bar working pressure.
– 7 bar maximum air pressure.
• The stapler is designed for use with original Josef
Kihlberg staples only.
• Magazine loading: Loaded from above.
• Firing of the stapler: Single shot firing.
• Air consumption per shot :0,85 1 at 6 bar operating
pressure.
SAFETY WARNINGS CONTINUED
• Never point the stapler at yourself or at anyone else,
whether it contains staples or not. Always remove
your finger from the trigger when not driving staples.
• Connect the stapler to the compressed air line
before loading staples. Maximum air pressure is
7 bar.
• Ensure that the air hose has the right dimension
to avoid pressure drops which might cause
malfunctioning. Minimum ¼".
• The stapler and the hose must have a coupling
which automatically bleeds all air pressure from the
stapler when it is disconnected.
• Avoid personal injury. Never hold your hand or
another part of your body under the stapler.
• Do not load the stapler with the trigger depressed.
• Use only Josef Kihlberg JK590 staples: Item # S-18712,
S-18713 and S-18714.
• Always place yourself in a firmly balanced position
when using or handling the stapler.
πCHICAGO•ATLANTA•DALLAS•LOSANGELES•MINNEAPOLIS•NYC/PHILA•SEATTLE•MEXICO•CANADA
1-800-295 -5510
uline.com