U-Line KIHLBERG H-3531 User manual

PAGE 1 OF 3 1012 IH-3531
πH-3531
KIHLBERG PNEUMATIC
PLIER STAPLER
1- 800 -295-5510
uline.com
OPERATION
LOADING THE MAGAZINE
The correct type of staples for the tool is marked on the
righthand side of the magazine. Load the magazine as
follows:
1. Pull the magazine lid (A) all the way out. (See Figure 1)
2. Place the staple strip (B) into the staple rail (C) from
the lefthand side. (See Figure 2)
3. Push the lid all the way forward until it clicks into
place. (See Figure 3)
USING THE STAPLER
WARNING! Place the stapler on a stable work
surface. Do not drive staples into hard or brittle
materials. Do not drive staples at too steep
an angle or too close to the edge of the work.
Doing so may cause injury. Be sure that the
stapler is not pointed at yourself or anyone else
when connecting it to the compressed air line.
To avoid damage, never fire the stapler when it
is empty.
1. Adjust the air pressure to the lowest setting to drive the
staples to the desired depth. Start at approximately
5.5 bar and raise by 0.5 bar increments until the
correct operating pressure is found.
CAUTION! Never exceed 7 bar air pressure.
A
Figure 1
CB
Figure 2
Figure 3

PAGE 2 OF 3 1012 IH-3531
OPERATION CONTINUED
2. Place the item to be stapled (D) below the stapler
head (E). (See Figure 4) Pull the trigger (F). REMOVING STUCK STAPLES
WARNING! Always disconnect the tool from the
air supply, empty the magazine, and read the
safety warnings before starting maintenance.
1. Pry the door open from the lefthand side with a
screwdriver.
2. Remove any staple remnants inside the tool nozzle
and close the door again until it clicks shut.
D
EF
Figure 4
SAFETY WARNINGS
NOTE: Read the following warnings to prevent
injuries to yourself and those around you.
• Never use oxygen, combustible gases, CO2, steam
or high pressure gas tanks as power sources. The
stapler may explode and cause serious injury.
• Use only dry, clean, pressure-regulated compressed
air to drive the stapler.
• Eye protection must always be worn by the operator
and others in the work area.
• Always use personal protection equipment as
required, such as ear protection, hard hats, etc.
• Never use a defective stapler. Ensure the trigger
operates properly and all screws and nuts are
securely tightened at all times.
• Do not modify the stapler.
• Always disconnect the stapler from the air supply
and empty the magazine when the stapler is not in
use or when servicing.
• Never leave a loaded stapler unattended.
• Always assume that the stapler is loaded.
• No horseplay. Respect the stapler as a working
implement.
• Never point the stapler at yourself or anyone else,
whether it contains staples or not. Always remove
finger from trigger when not driving staples.
• Connect the stapler to the compressed air line
before loading staples. Maximum air pressure is 7
bar.
• Ensure that the air hose has the right dimension
to avoid pressure drops which might cause
malfunctioning. Minimum: ¼".
• The stapler and the hose must have a coupling
which automatically bleeds all air pressure from the
stapler when it is disconnected.
• Avoid personal injury. Never hold your hand in the
jaws of the stapler.
• Do not load the stapler with the trigger depressed.
• Use only Josef Kihlberg staples, type 779: Uline items
S-18708 and S-18709.
• Always place yourself in a firmly balanced position
when using or handling the stapler.

PAGE 3 OF 3 1012 IH-3531
MAINTENANCE
SPECIFICATIONS
• Always disconnect the tool from the air supply,
empty the magazine and read the safety warnings
before starting maintenance.
• Check that all safety devices function properly,
especially that the trigger moves freely and that all
screws and nuts are securely tightened.
• This tool does not require special servicing. It
only needs regular cleaning with a non-corrosive
cleaning agent. Do not remove any parts for
cleaning purposes.
• A small amount of lubricating oil is needed in the
nipple each day or 10 drops once a week to ensure
safe functioning.
• At high frequency stapling lubricating oil is
recommended.
• Contact Uline for more information: 1-800-295-5510.
MFG. PART NO. HEIGHT LENGTH WIDTH WEIGHT STAPLES LENGTH MAGAZINE
CAPACITY
JK20T779L 250mm 375mm 68mm 2,1kg 779 8–16mm 168
• Air pressure:
- Approx. 5-6 bar working pressure
- 7 bar maximum air pressure
• The stapler is designed for use with original Josef
Kihlberg staples only
• Magazine loading: Loaded from above
• Firing of the stapler: Single shot firing
• Air consumption per shot. :0,3 1 at 6 bar operating
pressure
πCHICAGO•ATLANTA•DALLAS•LOSANGELES•MINNEAPOLIS•NYC/PHILA•SEATTLE•MEXICO•CANADA
1-80 0 -295-5510
uline.com