Ubiquiti NanoStatonM Series User manual

17.02.2020 NanoStatonM/locoM Seres Quck Start Gude
https://dl.ubnt.com/qsg/NanoStatonM_NanoStatonlocoM/NanoStatonM_NanoStatonlocoM_EN.html 1/19
NanoStat  on M2/M3/M365/M5 Z  p T  e PoE (24V, 0.5A) w  th Mount  ng
Bracket
Power Cord
NanoStat  onloco M2/M5 Z  p T  e PoE (24V, 0.5A) w  th Mount  ng
Bracket
Package Contents
NSM2/NSM3/NSM365/NSM5
locoM2/locoM5
NanoStat  onM/locoM Ser  es Qu  ck Start Gu  de
All manuals and user guides at all-guides.com
all-guides.com

17.02.2020 NanoStatonM/locoM Seres Quck Start Gude
https://dl.ubnt.com/qsg/NanoStatonM_NanoStatonlocoM/NanoStatonM_NanoStatonlocoM_EN.html 2/19
Power Cord
NanoStat  onlocoM9 Z  p T  e PoE (24V, 0.5A) w  th Mount  ng
Bracket
Power Cord
locoM9
Installat  on Requ  rements
Sh  elded Category 5 (or above) cabl  ng w  th dra  n w  re should be used for all w  red
Ethernet connect  ons and should be grounded through the AC ground of the PoE.
We recommend that you protect your networks from harmful outdoor env  ronments
and destruct  ve ESD events w  th  ndustr  al-grade, sh  elded Ethernet cable from
Ub  qu  t  . For more deta  ls, v  s  t u  .com/toughcable
Surge protect  on should be used for all outdoor  nstallat  ons. We recommend that
you use two Ethernet Surge Protectors, model ETH-SP, one near the NanoStat  on and
the other at the entry po  nt to the bu  ld  ng. The ETH-SP w  ll absorb power surges
and safely d  scharge them  nto the ground.
NanoStat  onM/locoM Ser  es Qu  ck Start Gu  de
All manuals and user guides at all-guides.com

17.02.2020 NanoStatonM/locoM Seres Quck Start Gude
https://dl.ubnt.com/qsg/NanoStatonM_NanoStatonlocoM/NanoStatonM_NanoStatonlocoM_EN.html 3/19
Hardware Overv  ew
NSM2/NSM3/NSM365/NSM5/locoM2/locoM5
NanoStat  onM/locoM Ser  es Qu  ck Start Gu  de
All manuals and user guides at all-guides.com

17.02.2020 NanoStatonM/locoM Seres Quck Start Gude
https://dl.ubnt.com/qsg/NanoStatonM_NanoStatonlocoM/NanoStatonM_NanoStatonlocoM_EN.html 4/19
Power LED
The LED w  ll l  ght green when the dev  ce  s connected to a power source.
NanoStat  onM/locoM Ser  es Qu  ck Start Gu  de
All manuals and user guides at all-guides.com

17.02.2020 NanoStatonM/locoM Seres Quck Start Gude
https://dl.ubnt.com/qsg/NanoStatonM_NanoStatonlocoM/NanoStatonM_NanoStatonlocoM_EN.html 5/19
LAN1 LED
LAN2 LED
S  gnal LEDs
Secondary Port
Ma  n/LAN* Port
Reset Button
The LED w  ll l  ght steady green when an act  ve Ethernet connect  on  s made to the
Ma  n/LAN port and ash when there  s act  v  ty.
(NanoStat  on M2/M3/M5 only) The LED w  ll l  ght steady green when an act  ve
Ethernet connect  on  s made to the Secondary port and ash when there  s act  v  ty.
In a  rOS®, you can mod  fy the threshold values for the w  reless s  gnal strength LEDs
on the Advanced tab under S  gnal LED Thresholds. The default values are shown
below:
(NanoStat  onM2/M3/M5 only) Th  s 10/100 Ethernet port  s used for br  dg  ng and
supports software-conf  gurable PoE passthrough.
Note: To use PoE passthrough on the Secondary port, a 24V, 1A PoE
adapter  s requ  red.
Th  s 10/100 Ethernet port  s used to connect the power and should be connected to
the LAN and DHCP server.
To reset to factory defaults, press and hold the Reset button for more than 10
seconds wh  le the dev  ce  s powered on. Alternat  vely, the dev  ce may be reset
remotely v  a a Reset button located on the bottom of the PoE adapter.
* The Ma  n port  s labeled LAN on the NanoStat  onlocoM2/M5.
locoM9
NanoStat  onM/locoM Ser  es Qu  ck Start Gu  de
All manuals and user guides at all-guides.com

17.02.2020 NanoStatonM/locoM Seres Quck Start Gude
https://dl.ubnt.com/qsg/NanoStatonM_NanoStatonlocoM/NanoStatonM_NanoStatonlocoM_EN.html 6/19
Power LED
LAN1 LED
S  gnal LEDs
The LED w  ll l  ght green when the dev  ce  s connected to a power source.
The LED w  ll l  ght steady green when an act  ve Ethernet connect  on  s made to the
Ma  n/LAN port and ash when there  s act  v  ty.
In a  rOS®, you can mod  fy the threshold values for the w  reless s  gnal strength LEDs
on the Advanced tab under S  gnal LED Thresholds. The default values are shown
below:
NanoStat  onM/locoM Ser  es Qu  ck Start Gu  de
All manuals and user guides at all-guides.com
all-guides.com

17.02.2020 NanoStatonM/locoM Seres Quck Start Gude
https://dl.ubnt.com/qsg/NanoStatonM_NanoStatonlocoM/NanoStatonM_NanoStatonlocoM_EN.html 7/19
RP-SMA Antenna Connector
Ma  n/LAN Port
Reset Button
Reserved for future use.
Th  s 10/100 Ethernet port  s used to connect the power and should be connected to
the LAN and DHCP server.
To reset to factory defaults, press and hold the Reset button for more than 10
seconds wh  le the dev  ce  s powered on. Alternat  vely, the dev  ce may be reset
remotely v  a a Reset button located on the bottom of the PoE adapter.
Installat  on
1.
2.
NanoStat  onM/locoM Ser  es Qu  ck Start Gu  de
All manuals and user guides at all-guides.com

17.02.2020 NanoStatonM/locoM Seres Quck Start Gude
https://dl.ubnt.com/qsg/NanoStatonM_NanoStatonlocoM/NanoStatonM_NanoStatonlocoM_EN.html 8/19
3.
4.
NanoStat  onM/locoM Ser  es Qu  ck Start Gu  de
All manuals and user guides at all-guides.com

17.02.2020 NanoStatonM/locoM Seres Quck Start Gude
https://dl.ubnt.com/qsg/NanoStatonM_NanoStatonlocoM/NanoStatonM_NanoStatonlocoM_EN.html 9/19
5.
NanoStat  onM/locoM Ser  es Qu  ck Start Gu  de
All manuals and user guides at all-guides.com

17.02.2020 NanoStatonM/locoM Seres Quck Start Gude
https://dl.ubnt.com/qsg/NanoStatonM_NanoStatonlocoM/NanoStatonM_NanoStatonlocoM_EN.html 10/19
6.
NanoStat  onM/locoM Ser  es Qu  ck Start Gu  de
All manuals and user guides at all-guides.com