Ubiquiti NanoStationM Series User manual

29/01/22, 13:44
NanoStationM/locoM Series Quick Start Guide
https://dl.ui.com/qsg/NanoStationM_NanoStationlocoM/NanoStationM_NanoStationlocoM_EN.html
1/16
NanoStation
M2/M3/M365/M5
Gravata PoE (24V, 0,5A) com suporte
de montagem
Cabo de alimentação
NanoStationloco M2/M5 Gravata PoE (24V, 0,5A) com suporte
de montagem
conteúdo do pacote
NSM2/NSM3/NSM365/NSM5
locoM2/locoM5
Guia de início rápido da série NanoStationM/locoM

29/01/22, 13:44
NanoStationM/locoM Series Quick Start Guide
https://dl.ui.com/qsg/NanoStationM_NanoStationlocoM/NanoStationM_NanoStationlocoM_EN.html
2/16
Cabo de alimentação
NanoStationlocoM9 Gravata PoE (24V, 0,5A) com suporte
de montagem
Cabo de alimentação
locoM9
Requerimentos de instalação
Cabeamento blindado de Categoria 5 (ou superior) com fio dreno deve ser
usado para todas as conexões Ethernet com fio e deve ser aterrado através do
terra CA do PoE.
We recommend that you protect your networks from harmful outdoor
environments and destructive ESD events with industrial-grade, shielded
Ethernet cable from Ubiquiti. For more details, visit ui.com/toughcable
Surge protection should be used for all outdoor installations. We recommend
that you use two Ethernet Surge Protectors, model ETH-SP, one near the
NanoStation and the other at the entry point to the building. The ETH-SP will
absorb power surges and safely discharge them into the ground.
Guia de início rápido da série NanoStationM/locoM

29/01/22, 13:44
NanoStationM/locoM Series Quick Start Guide
https://dl.ui.com/qsg/NanoStationM_NanoStationlocoM/NanoStationM_NanoStationlocoM_EN.html
3/16
Hardware Overview
NSM2/NSM3/NSM365/NSM5/locoM2/locoM5
Guia de início rápido da série NanoStationM/locoM

29/01/22, 13:44
NanoStationM/locoM Series Quick Start Guide
https://dl.ui.com/qsg/NanoStationM_NanoStationlocoM/NanoStationM_NanoStationlocoM_EN.html
4/16
Power LED
The LED will light green when the device is connected to a power source.
Guia de início rápido da série NanoStationM/locoM

29/01/22, 13:44
NanoStationM/locoM Series Quick Start Guide
https://dl.ui.com/qsg/NanoStationM_NanoStationlocoM/NanoStationM_NanoStationlocoM_EN.html
5/16
LAN1 LED
LAN2 LED
Signal LEDs
Secondary Port
Main/LAN* Port
Reset Button
The LED will light steady green when an active Ethernet connection is made to
the Main/LAN port and flash when there is activity.
(NanoStation M2/M3/M5 only) The LED will light steady green when an active
Ethernet connection is made to the Secondary port and flash when there is
activity.
In airOS®, you can modify the threshold values for the wireless signal strength
LEDs on the Advanced tab under Signal LED Thresholds. The default values
are shown below:
(NanoStationM2/M3/M5 only) This 10/100 Ethernet port is used for bridging
and supports software-configurable PoE passthrough.
Note: To use PoE passthrough on the Secondary port, a 24V, 1A PoE
adapter is required.
This 10/100 Ethernet port is used to connect the power and should be
connected to the LAN and DHCP server.
To reset to factory defaults, press and hold the Reset button for more than 10
seconds while the device is powered on. Alternatively, the device may be reset
remotely via a Reset button located on the bottom of the PoE adapter.
* The Main port is labeled LAN on the NanoStationlocoM2/M5.
locoM9
Guia de início rápido da série NanoStationM/locoM

29/01/22, 13:44
NanoStationM/locoM Series Quick Start Guide
https://dl.ui.com/qsg/NanoStationM_NanoStationlocoM/NanoStationM_NanoStationlocoM_EN.html
6/16
Power LED
LAN1 LED
Signal LEDs
The LED will light green when the device is connected to a power source.
The LED will light steady green when an active Ethernet connection is made to
the Main/LAN port and flash when there is activity.
In airOS®, you can modify the threshold values for the wireless signal strength
LEDs on the Advanced tab under Signal LED Thresholds. The default values
are shown below:
Guia de início rápido da série NanoStationM/locoM

29/01/22, 13:44
NanoStationM/locoM Series Quick Start Guide
https://dl.ui.com/qsg/NanoStationM_NanoStationlocoM/NanoStationM_NanoStationlocoM_EN.html
7/16
RP-SMA Antenna Connector
Main/LAN Port
Reset Button
Reserved for future use.
This 10/100 Ethernet port is used to connect the power and should be
connected to the LAN and DHCP server.
To reset to factory defaults, press and hold the Reset button for more than 10
seconds while the device is powered on. Alternatively, the device may be reset
remotely via a Reset button located on the bottom of the PoE adapter.
Installation
1.
2.
Guia de início rápido da série NanoStationM/locoM

29/01/22, 13:44
NanoStationM/locoM Series Quick Start Guide
https://dl.ui.com/qsg/NanoStationM_NanoStationlocoM/NanoStationM_NanoStationlocoM_EN.html
8/16
3.
4.
Guia de início rápido da série NanoStationM/locoM

29/01/22, 13:44
NanoStationM/locoM Series Quick Start Guide
https://dl.ui.com/qsg/NanoStationM_NanoStationlocoM/NanoStationM_NanoStationlocoM_EN.html
9/16
5.
Guia de início rápido da série NanoStationM/locoM

29/01/22, 13:44
NanoStationM/locoM Series Quick Start Guide
https://dl.ui.com/qsg/NanoStationM_NanoStationlocoM/NanoStationM_NanoStationlocoM_EN.html
10/16
6.
Connecting Power
WARNING: The switch port must comply with the power specifications
listed in this Quick Start Guide.
OR
Optional
Accessing airOS
Verify connectivity in the airOS Configuration Interface.
1. Make sure that your host system is connected via Ethernet to the device.
Guia de início rápido da série NanoStationM/locoM