UfiSpace Outdoor R1 Series User guide

Outdoor LoRa Gateway
Installation Quick Guide
1Contents of delivery
5Cabling
6Network Access
4Optional Accessories Recommended
3Installation
Install GPS Antenna
Install Rear Bracket to Gateway
Pole Mounting
Install Surge Protection Cable
Install 8 dBi LoRa Antenna to Pole
Install 11-57 VDC Port Cable
Install SIM Card
2Preparing the Installation
Connectors and Interfaces
All product specications are subject to change without notice
This is a quick reference guide for
uSpace Outdoor R1 Series LoRa Gateway installation.
This gateway is designed for outdoor pole mounting installation.
540.01511.015

All product specications are subject to change without notice
- 2 -
This Outdoor LoRa Gateway is designed with Semtech Technology to provide low
power and wide area (LPWA) unlicensed band wireless connection. This gateway
supports connectivity for wide range of Internet of Things (IOT) applications.
1 Contents of Delivery
1 x LTE
0 dBi Antenna
2 x Hose Clamp 1 x Surge
Protection Cable
1 x Antenna
Extension Cable
1 x Pole
Mounting Bracket
1 x Gateway
Rear Bracket
1 x Screw Kit
(3pcs)
1 x Screw Kit
(4pcs)
Quick Guide
1 x Installation
Quick Guide
1 x Outdoor LoRa Gateway
with water protection cap on
N-Type connector ports
User Manual
1 x User Manual
60 Watts PoE Adapter
(optional)
1 x DC Input
Cable Gland
(optional)
1 x DC Input
Connector
(optional)
1 x GPS Antenna
1 x Screw Kit
(4pcs)
Items
1x Outdoor LoRa Gateway with water protection cap on N-Type connector ports
Metal Caps: V2.1 HW (3 for LTE version, 2 for non-LTE version)
1 x Antenna Extension Cable (for 3, 8 or 9 dBi LoRa antenna, cable length 60.96 3cm)
1x Outdoor LoRa Gateway User Manual and Installation Quick Guide
1x LTE 0 dBi Antenna (only for model with LTE function)
1x Screw Kit (4pcs) for GPS Antenna
1x Screw Kit (3pcs) for Pole Mounting Bracket
1x DC Input Connector (only for model with 11-57 VDC function)
1x DC Input Cable Gland (only for model with 11-57 VDC function)
1x 60 Watts PoE Adapter (optional)
1x Screw Kit (4pcs) for Gateway Rear Bracket
2x Hose Clamp
1x Surge Protection Cable
1x Pole Mounting Bracket
1x Gateway Rear Bracket
1x GPS Antenna (cable length 43.6 cm)

All product specications are subject to change without notice
- 3 -
2 Preparing the Installation
Caution
Must make sure all antennas are installed properly before apply PoE power to the gateway.
For un-connected N-Type Antenna Port, MUST install a " N-Type Water Protection Cap" to
prevent water leaking into the device. " N-Type Water Protection Caps" are supplied with
the gateway. MUST not install or remove GPS, LoRa or LTE Antenna when DC power is
applied to the Gateway. It may damage the device.
Surge Protection Cable must be properly connected to gateway housing and earth ground.
Connectors and Interfaces
V2.1 R1 Series Gateway
GPS Antenna
USB/ LED/ Reset48 VDC-IN/ PoE
LoRa Antenna 2LoRa Antenna 1
11-57 VDC IN SIM Card
LTE Antenna Pressure Vent

All product specications are subject to change without notice
- 4 -
3 Installation
Install GPS Antenna
The GPS Antenna can be installed to top of gateway housing directly and can be
remove from pole together with gateway.
Install Rear Bracket to Gateway
Install the Rear Bracket to Outdoor Gateway housing with 4 screws.
V2.1 Gateway

All product specications are subject to change without notice
- 5 -
Pole Mounting
Our mounting bracket is designed for pole mount only.
V2.1 Gateway
Gateway
11-57VDC LTE Antenna
PoE Cable
(Must use shielded Ethernet cable)
PoE Adapter
GPS Antenna
(recommended position)
RF Feeder Cable
Surge Protector
(optional)
Surge Protector (optional)

All product specications are subject to change without notice
- 6 -
Connecting Earth Ground to Unit
Warning
The equipment has a separate protective earthing terminal on the chassis that must be permanently connected to
earth ground to adequately ground the chassis and protect the operator from electrical hazards.
The product shall be installed by a qualied service person and the installation shall conform to all local codes.
Caution
Before equipment installation begins, ensure that a service personnel has attached an appropriate grounding lug to
the grounding cable that you supply.
Power installation must be performed with qualied electrician and followed with National Electrical Code,
ANSI/NFPA 70 and Canadian Electrical Code, Part I, CSA C22.1.
Warning
At rst before powered on, connect the frame of the unit to earth.
For earthing wire, green-and-yellow insulation is required and the cross-sectional area of the conductor must be
more than 10 AWG.
1Connect one end of the grounding cable to a proper earth ground.
2Place the grounding lug attached to the grounding cable over the protective earthing terminal.
3Secure the grounding lug to the protective earthing terminal with the washers and screws.
4Dress the grounding cable and ensure that it does not touch or block access to other components.
To connect earth ground to Unit
Hook Gateway onto the Pole Bracket
After hooking gateway onto the pole bracket,
these 2 screws must be installed to secure
gateway’s vertical direction.
IMPORTANT
Maximum 55Kg.cm
torque for hose clamp
Vertical Mount
Minimum OD 40 mm
Maximum OD 120 mm
Install Hose Clamp to Pole Hose Clamp

All product specications are subject to change without notice
- 7 -
Surge Protection Cable must be properly connected to gateway’s Pole Bracket and
earth ground.
Install Coaxial Surge Protector to LoRa, LTE & GPS RF Ports
Recommend to add external RF coaxial Surge Protector to enhance protection level and
must be connected to the Lighting Protection System, lighting rod to earth ground.
Additional Surge Protection to PoE and DC Ports
You can add external surge protector to PoE and 11-57 VDC ports to enhance its surge
protection level.
Install Surge Protection Cable
Install 8dBi LoRa Antenna to Pole
LoRa Antenna
Antenna port water leakage enhancement
Pole ø70-90 mm
Antenna
Hose Clamp
1600 5 (868MHz)
1500 5 (920MHz)
+
_
+
_
Recommend to apply 3M (2166) waterproong
tape on antenna port to enhance water leakage
protection.
Surge Protection Cable is
installed at Pole Bracket.
P8AX09-6G-N/MF
PoE Port Surge Protector (Microsemi PD-OUT/SP11)
Earth Ground

All product specications are subject to change without notice
- 8 -
Install 11-57 VDC Port Cable
4 Optional Accessories Recommended
Items
LoRa 8 or 9 dBi antenna
LoRa 0 dBi antenna (optional, for direct connecting to Gateway N-Type connector application, without antenna extension cable)
LoRa 3 dBi antenna (optional, for direct connecting to Gateway N-Type connector application, without antenna extension cable)
PoE Adapter (60 Watts)
LoRa 0 dBi antenna 60 Watts PoE AdapterLoRa 3 dBi antennaLoRa 8 or 9 dBi antenna
Install + & - DC wires to the green color DC Input Connector provided in the box before
inserting it to gateway’s 11-57 VDC port.
Install SIM Card
Must insert SIM card at correct direction as shown in the SIM card port mylar.
SIM
DC Input Cable Gland
DC Input Connector

All product specications are subject to change without notice
- 9 -
5 Cabling
LoRa Antenna #1 LoRa Antenna #2
(optional)
LTE Antenna
PoE Adapter (must use shielded
Ethernet cable)
GPS Antenna
11-57 VDC
5 VDC output
for supporting
5V Active
GPS Antenna
V2.1 Gateway

All product specications are subject to change without notice
- 10 -
6 Network Access
Use Default Conguration
Caution
The backhaul network conguration on Outdoor LoRa Gateway supports several connection types
which can be selected as primary and secondary WAN. When device power up, it tries to bring up
primary WAN interface. If primary WAN is not available, the device will try to bring up the secondary
WAN interface. Device still continue to try to monitor the availability of the primary WAN interface.
Once primary interface is ready, device will switch to primary WAN immediately and shutdown
secondary WAN.
The primary WAN is congured as Ethernet with DHCP client through the PoE connectivity. On the
device with LTE support, LTE is congured as secondary WAN. In the installation environment, there
is no extra conguration is needed if a DHCP server is available through Ethernet connection. For
making device to have sucient interface parameters, following information has to be supplied by
DHCP server:
[Device IP] [Device Netmask] [Default Gateway] [DNS server]
Must make sure all antennas are installed properly before apply PoE power to the gateway.
For un-connected N-Type Antenna Port, MUST install a " N-Type Water Protection Cap" to
prevent water leaking into the device. " N-Type Water Protection Caps" are supplied with
the gateway. MUST not install or remove GPS, LoRa or LTE Antenna when DC power is
applied to the Gateway. It may damage the device.
Surge Protection Cable must be properly connected to gateway housing and earth ground.

All product specications are subject to change without notice
- 11 -
Changing Conguration
If default conguration does not t the usage in installation environment, please use setup showed
in following photo to change conguration. You will need a Router that have DHCP server to oer IP
to Outdoor LoRa Gateway, or use a switch/ hub and running a DHCP server on PC for the same
purpose. After device acquired IP, you need to use PC to access device. As for the detail of changing
conguration, please refer to User Manual.
V2.1 Gateway
LoRa Antenna #1 LoRa Antenna #2
(optional)
LTE Antenna
PoE Adapter
Ethernet Router or Switch to
assign IP to LoRa Gateway
USB/ LED/ Reset
GPS Antenna
SIM Card
11-57 VDC-IN
48 VDC-IN/ PoE

All product specications are subject to change without notice
- 12 -
WAN Page
This page describes the backhaul conguration. There are three kinds of backhaul which are Ethernet
over PoE, WiFi client mode and LTE (if both LTE module and SIM card are installed) and can be selected
and congured through their own settings.
WARNING :
HOT SURFACE DO NOT TOUCH !!
Before touching it, special attention or protection is necessary.
WARNING :
This equipment is intended to be used in a Restricted
Access Location, with access limited to SERVICE
PERSONAL and USERS authorized to be in that location.
Unsafe

All product specications are subject to change without notice
- 13 -
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o and on, the user is encouraged to try
to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modications not expressly approved by the party responsible for compli-
ance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Country Code selection feature to be disabled for products marketed to the US/CANADA
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
Radiation Exposure Statement:
IMPORTANT NOTE

All product specications are subject to change without notice
- 14 -
Professional installation instruction
Please be advised that due to the unique function supplied by this product, the device is intended for
use with our interactive entertainment software and licensed third-party only. The product will be
distributed through controlled distribution channel and installed by trained professional and will not be
sold directly to the general public through retail store.
1. Installation personal
This product is designed for specic application and needs to be installed by a qualied personal who
has RF and related rule knowledge. The general user shall not attempt to install or change the setting.
2. Installation location
The product shall be installed at a location where the radiating antenna can be kept 40cm from
nearby person in normal operation condition to meet regulatory RF exposure requirement.
3. External antenna
Use only the antennas which have been approved by the applicant. The non-approved antenna(s)
may produce unwanted spurious or excessive RF transmitting power which may lead to the
violation of FCC/IC limit and is prohibited.
4. Installation procedure
Please refer to user’s manual for the detail.
5. Warning
Please carefully select the installation position and make sure that the nal output power does not
exceed the limit set force in relevant rules. The violation of the rule could lead to serious federal
penalty.