UfiSpace S9510-28DC Manual

Hardware Installation Guide
S9510-28DC
Disaggregated Cell Site
Gateway
R1.0

S9510-28DC Hardware Installation Guide | i
Table of Contents
1Overview.............................................................................................................................1
2Preparation.........................................................................................................................2
2.1 Installation Tools......................................................................................................................2
2.2 Installation Environment Requirements..................................................................................3
2.3 Preparation Check List.............................................................................................................4
3Package Contents................................................................................................................5
3.1 Accessory List...........................................................................................................................5
3.2 Component Physical Information............................................................................................6
4Identifying Your System.......................................................................................................7
4.1 S9510-28DC DC Version Overview ..........................................................................................7
4.2 S9510-28DC AC Version Overview...........................................................................................8
4.3 DC Version PSU Overview........................................................................................................9
4.4 AC Version PSU Overview......................................................................................................10
4.5 Fan Overview .........................................................................................................................10
4.6 Port Overview ........................................................................................................................11
5Rack Mounting..................................................................................................................12
6Installing Fan Modules.......................................................................................................13
7Installing Power Supply Units ............................................................................................14
8Grounding the Router........................................................................................................16
9Connecting Power .............................................................................................................18
9.1 DC Version..............................................................................................................................18
9.2 AC Version..............................................................................................................................19
10 Verifying System Operation...............................................................................................20
10.1 Front Panel LED....................................................................................................................20
10.2 PSU FRU LED ........................................................................................................................21
10.3 Fan FRU LED.........................................................................................................................21
11 Initial System Setup...........................................................................................................22
12 Cable Connections.............................................................................................................23
12.1 Connecting the USB Extender Cable....................................................................................23

S9510-28DC Hardware Installation Guide | ii
12.2 Connecting a Cable to the ToD Interface.............................................................................23
12.3 Connecting the GNSS Interface ...........................................................................................23
12.4 Connecting the 1PPS Interface ............................................................................................24
12.5 Connecting the 10MHz Interface.........................................................................................24
12.6 Connecting the Transceiver.................................................................................................25
13 Cautions............................................................................................................................26

S9510-28DC Hardware Installation Guide | 1
1Overview
The UfiSpace S9510-28DC is a high-performance, versatile open networking white box
router that is designed to address the changing needs of backhaul transport requirements
as Telecoms make the transition from legacy technologies towards 5G.
It enables telecoms and service providers to deploy disaggregated open network
infrastructure to lower costs and rapidly scale existing services for edge computing, mobile
backhaul, and broadband access applications.
The S9510-28DC is future-proofed with a powerful 8-core processor, 25GE/100GE/400GE
high-speed interfaces, and full timing features supporting IEEE 1588v2 and SyncE, which
enables service providers to easily migrate from 2G, 3G, 4G BBUs to 5G RAN. It is suitable
for both indoor and outdoor deployments with redundant, hot swappable components for
convenience, increased availability, reliabilityand lower costs of maintenance
This document describes the hardware installation process for S9510-28DC.

S9510-28DC Hardware Installation Guide | 2
2Preparation
Installation Tools
Screw Driver
Crimping tool
14 AWG wire with ring terminal for
DC power supply
6-AWG wire for grounding
Wire-stripping tools for
stripping 6-AWG copper wire
Console cable
•PC with terminal emulation software. Refer to the "Initial System Setup" section for
details.
•Baud rate: 115200 bps
•Data bits: 8
•Parity: None
•Stop bits: 1
•Flow control: None

S9510-28DC Hardware Installation Guide | 3
Installation Environment Requirements
•Power Reserve: The S9510-28DC power supply is available with:
1. DC Version: 1+1 active-active -48 voltage DC power supply field replaceable unit or;
2. AC Version: 1+1 active-active universal 100-240V AC power supply field replaceable unit.
To ensure the active-active feed power design functions properly, a field with dual power
circuit is recommend with a reserve of at least 400 watts on each power circuit.
•Space Clearance: The S9510-28DC width is 17.32 inches (44cm) and shipped with a rack
mount brackets suitable for 19 inch (48.3cm) wide racks. The depth of the S9510-28DC
chassis is 11.89 inches (30.2cm) without the field replaceable units (FRUs) and comes with
adjustable mounting rails suitable for rack depths of 22 inches (55.9cm) to 33 inches
(83.8cm). The handle for the fan units will extend outwards by 1 inch (2.5cm) and the handle
for the power supplies will extend outwards by 1.06 inches (2.7cm). Therefore, to
accommodate the fan and power supply handles, a minimum space clearance of 2 inches
(5.1cm) is needed at the front and back of the S9510-28DC. A total minimum reserve depth of
16 inches (40.6cm) is required.
Figure 1.
Figure 2.

S9510-28DC Hardware Installation Guide | 4
• Cooling: The S9510-28DC airflow direction is front-to-back. Make sure the equipmenton
the same rack have the same airflow direction.
Figure 3.
Figure 4.
Preparation Check List
Task
Check
Date
Power voltage and electric current requirement
DC version: -48V DC, 16-8 ampere maximum or;
AC version: 100-240V, 6-3 ampere
Installation spacing and weight load requirement:
S9510-28DC is 1RU (1.75”/4.5cm) in height, 19” (48.3cm) in width,
and 16” (40.6cm) in depth without considering cable routing
Thermal requirement
S9510-28DC working temperature is -40 to 65°C (-40°F to 140°F),
airflow direction is front-to-back
Installation tools required
#2 Philips Screwdriver, 6-AWG wire stripper, and crimping tool
Accessories required
PC with terminal emulation software, console cable, 14-AWGwire
with ring terminal for power, 6-AWG wire for grounding

S9510-28DC Hardware Installation Guide | 5
3Package Contents
Accessory List
Item
Description
Spec. & Dimensions
Qty.
Weight
1
Grounding Lug
1.97” x 0.44” x 0.3”
(#6 AWG)
(50 x 11.1 x 7.5mm)
1 pcs
0.22lbs (10.0g)/pcs
2
Screw Kit (for
Grounding Lug)
2 x Screws M4*L8.0mm
4 x M4 Lock Washers
6 sets
0.008lbs (3.8g)/set
3
Rack Mount Bracket
1.98” x 1.69” x 0.79”
(19” width rack)
(50.4 x 43 x 20mm)
2 pcs
0.15lbs (67.2g)/2 pcs
(0.07lbs (33.6g)/pcs)
4
Screw Kit (for Rack
Mount Bracket)
8 x Screws M4.0*L6.5mm
8 sets
0.01lbs (6.5g)/set
5
Adjustable Mounting
Rail (for 4 posts)
16.02” x 1.69” x 0.83”
(22” to 33” rack depth)
(406.8 x 43 x 21mm)
2 pcs
1.79lbs (810g)/2 pcs
(0.89lbs (405g)/pcs)
6
Screw Kit (for
Adjustable Mounting
Rail)
8 x Screws M4.0*L6.5mm
8 sets
0.01lbs (6.5g)/set
7
USB 3.0A Cable
Type Male to Female
200mm
7.87” (200mm)
1 pcs
0.021lbs (9.7g)/pcs

S9510-28DC Hardware Installation Guide | 6
Component Physical Information
Specification
Item
Description
Weight
Total package contents
22.05lbs (10kg)
Chassis without FRU
10.8lbs (4.9kg)
DC/AC PSU
1.5lbs (691g)
Fan
0.2lbs (90g)
Ground lug
0.022lbs (10g)
Rack mount bracket
0.07lbs (33.6g)
Adjustable mounting rail
0.89lbs (405g)
USB extension cord
0.021lbs (9.7g)
Screw kit for ground lug
0.008lbs (3.8g) per set
Screw kit for rack mount bracket
and adjustable mounting rail
0.1lbs (6.5g) per set
Dimension
S9510-28DC (W x D x H)
17.32” x 11.89” x 1.713”
(440 x 302 x 43.5mm)
PSU (W x D x H)
1.99” x 8.31” x 1.58” (50.5 x 211 x 40.2mm)
Fan (W x D x H)
1.57” x 1.57” x 1.1” (40 x 40 x 28mm)

S9510-28DC Hardware Installation Guide | 7
4Identifying Your System
S9510-28DC DC Version Overview
Figure 5.