Unfinished Furniture of Wilmington SV-40A User manual

ITEM NO.: SV-40A AND SV-40B
REVISED MAY 31, 2019
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 1 -
ASSEMBLY INSTRUCTIONS
WARNING!
Serious or fatal injuries can occur from furniture tip over. Use tip over restraint
(steel band included) to secure this product to the wall.
Description
Item No.
: PREVAIL SERVER
: SV-40A AND SV-40B

ITEM NO.: SV-40A AND SV-40B
REVISED MAY 31, 2019
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your product. Protect the surface of the product with cloth if you are using any
product with rubber feet or base.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: SV-40A AND SV-40B
REVISED MAY 31, 2019
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 3 -
PART LIST SV-40A
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top
1
B
Bottom panel
1
C
Leg frame
(L-R)
2
D
Crossbar
1
E
Shelf side
(L-R)
2
F
Shelf center
1

ITEM NO.: SV-40A AND SV-40B
REVISED MAY 31, 2019
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 4 -
PART LIST SV-40B
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
G
Vertical panel
(L-R)
2
H
Side panel
(L-R)
2
I
Joint connector
block
4
J
Center Door
(L-R)
2
K
Side Door
(L-R)
2
L
Side back
panel
2
M
Center back
panel
1

ITEM NO.: SV-40A AND SV-40B
REVISED MAY 31, 2019
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 5 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Short Bolt
(M6 x 30mm)
28
2
Medium Bolt
(M6 x 60mm)
2
3
Long Bolt
(M6 x 110mm)
4
4
Lock Washer
(6.5 x 11mm)
34
5
Small Flat Washer
(6.5 x 13mm)
32
6
Large Flat Washer
(6.5 x 19mm)
2
7
Short Screw
(M3.5 x 15mm)
67
8
Shelf support
bracket
12
9
Long Screw
(M4 x 35mm)
2
10
Steel band
2
11
L-bracket
4
12
Allen Key
(M4 x 30mm x 110mm)
1
NOTE: HARDWARE IS PACKED IN CARTON SV-40B.
NOTE: WARNING LABEL (INCLUDED)

ITEM NO.: SV-40A AND SV-40B
REVISED MAY 31, 2019
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 6 -
STEP 1
Attach vertical panels (G) to top (A) with bolts (1), and washers (4) and (5) as shown below. Tighten
with Allen key (12).
STEP 2
Attach bottom panel (B) to vertical panels (G) with bolts (1), and washers (4) and (5) as shown below.
Tighten with Allen key (12).

ITEM NO.: SV-40A AND SV-40B
REVISED MAY 31, 2019
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 7 -
STEP 3
Insert crossbar (D) into leg frames (C) and attach with bolts (2), and washers (4) and (6) as shown
below. Tighten with Allen key (12).
STEP 4
Attach leg frames (C) to bottom panel (B) with bolts (3), and washers (4) and (5) as shown below. Tighten with
Allen key (12).

ITEM NO.: SV-40A AND SV-40B
REVISED MAY 31, 2019
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 8 -
STEP 5
Attach joint connector blocks (I) to the unit with bolts (1), and washers (4) and (5) as shown below.
Tighten with Allen key (12).
STEP 6
Attach side panels (H) to top (A) bottom panel (B) with bolts (1), and washers (4) and (5) as shown
below. Tighten with Allen key (12).
Attach side panels (H) to top (A) and bottom panel (B) with brackets (11) and screws (7) as shown
below. Tighten with a screwdriver.

ITEM NO.: SV-40A AND SV-40B
REVISED MAY 31, 2019
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 9 -
STEP 7
Slide back panels (L) and (M) into the grooves and attach with screws (7) as shown below. Tighten
with a screwdriver.
STEP 8
Attach doors (J) and (K) to the unit with screws (7) as shown below. Tighten with a screwdriver.

ITEM NO.: SV-40A AND SV-40B
REVISED MAY 31, 2019
Printed in Vietnam
THIS ITEM IS PACKED IN TWO CARTONS
- 10 -
STEP 9
Insert brackets (8) into the unit as shown below. Place shelves (E) and (F) on the brackets and attach
with screws (7). Tighten with a screwdriver.