Unfinished Furniture of Wilmington T-9B User manual

ITEM NO : T-9B AND T-142RT OR T-48RT OR T-52T
(PACKED IN SEPARATE BOX)
ISSUED JUN 08, 2016
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: HAMPSHIRE PEDESTAL FOR SOLID TOP
: T-9B AND T-142RT OR T-48RT OR T-52T
(PACKED IN SEPARATE BOX)

ITEM NO : T-9B AND T-142RT OR T-48RT OR T-52T
(PACKED IN SEPARATE BOX)
ISSUED JUN 08, 2016
Printed in Vietnam
- 2 -
BEFORE ASSEMBLY
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your table. Protect the surface of the table with cloth if you are using any product
with rubber feet or base.

ITEM NO : T-9B AND T-142RT OR T-48RT OR T-52T
(PACKED IN SEPARATE BOX)
ISSUED JUN 08, 2016
Printed in Vietnam
- 3 -
PART LIST T-142RT OR T-48RT OR T-52T
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top
1
PART LIST T-9B
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
B
Leg
4
C
Pedestal
column
1

ITEM NO : T-9B AND T-142RT OR T-48RT OR T-52T
(PACKED IN SEPARATE BOX)
ISSUED JUN 08, 2016
Printed in Vietnam
- 4 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Hexagon nut
(M8x13mm)
8
2
Lock washer
(8.5x13mm)
12
3
Flat washer
(2x8.5x19mm)
8
4
Wrench
(13mm)
1
5
Bolt
(M8x45mm)
4
6
Allen Key
(M4x30mmx120mm)
1
7
Large flat
washer
(2x8.5x22mm)
4
NOTE: HARDWARE IS PACKED IN CARTON T-9B.

ITEM NO : T-9B AND T-142RT OR T-48RT OR T-52T
(PACKED IN SEPARATE BOX)
ISSUED JUN 08, 2016
Printed in Vietnam
- 5 -
STEP 1
Attach legs (B) to the pedestal (C) with washers (2) and (3), and nuts (1) as shown below. Tighten with
the wrench (4).
Use the Allen key (6) to loosen the bolts and washers, and then remove the plate from bottom of the
table top (A) as shown below.
STEP 2

ITEM NO : T-9B AND T-142RT OR T-48RT OR T-52T
(PACKED IN SEPARATE BOX)
ISSUED JUN 08, 2016
Printed in Vietnam
- 6 -
Attach the plate on top of the pedestal (C) with bolts (5), and washers (2) and (7) as shown below.
Tighten with the Allen key (6).
Attach the plate to bottom of the top (A) with bolts and washers (from Step 2) as shown below.
Tighten with the Allen key (6).
STEP 3
STEP 4