Unfinished Furniture of Wilmington CANYON T-7840XT User manual

ITEM NO : T-7840XT AND T-7840XB
ISSUED DEC 19, 2014
Printed in Vietnam
- 1 - THIS ITEM IS PACKED IN 2 CARTONS
ASSEMBLY INSTRUCTIONS
Description
Item No.
: 40X60X78 CANYON TABLE
: T-7840XT AND T-7840XB

ITEM NO : T-7840XT AND T-7840XB
ISSUED DEC 19, 2014
Printed in Vietnam
- 2 - THIS ITEM IS PACKED IN 2 CARTONS
BEFORE ASSEMBLY
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to beginning
assembly, however, make sure all parts and hardware are included and free of obvious defect. If a part is
missing or defective, please contact the store where purchased. If hardware is missing, or you need help with
assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from
being scratched.
-Remove all wrapping material, including staples & packing straps before you start to assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the finish of your
table. Protect the surface of the table with cloth if you are using any product with rubber feet or base.
PART LIST T-7840XT
When unpacking, please carefully not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following parts:
NO Description Qty Sketch NO Description Qty Sketch
A Top 1 B
Extension
Leaf
1
PART LIST T-7840XB
When unpacking, please carefully not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following parts:
NO Description Qty Sketch NO Description Qty Sketch
C Bases 2
D Cross bar 2

ITEM NO : T-7840XT AND T-7840XB
ISSUED DEC 19, 2014
Printed in Vietnam
- 3 - THIS ITEM IS PACKED IN 2 CARTONS
HARDWARE LIST
When unpacking, please carefully not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO Description Qty Sketch NO Description Qty Sketch
1 Bolt
( M8x50mm) 16
2 Lock Washer
(8.5 x13mm) 16
3 Flat Washer
(8.5 x19mm) 16
4 Allen Key
(4x80mm) 1
NOTE: HARDWARE IS PACKED IN CARTON T-7840XB
STEP 1
Attach the bases (C) to the top (A) with bolts (1), and washers (2) and (3), as shown below. Tighten
with Allen key (4).

ITEM NO : T-7840XT AND T-7840XB
ISSUED DEC 19, 2014
Printed in Vietnam
- 4 - THIS ITEM IS PACKED IN 2 CARTONS
STEP 2
Attach the cross bars (D) to top (A) and bases (C) with bolts (1), and washers (2) and (3), as shown
below. Tighten with Allen key (4).
STEP 3
Unlock the table top from both sides underneath the top as shown below.
Pull the 2 parts of the table top apart.

ITEM NO : T-7840XT AND T-7840XB
ISSUED DEC 19, 2014
Printed in Vietnam
- 5 - THIS ITEM IS PACKED IN 2 CARTONS
STEP 4
Place the leaf (B) in the center of the top as shown below.
Push the table top closed. Lock the mechanism underneath 2 sides of the table top as shown below.