Uplift Desk ACU011 User manual

© UPLIFT Desk • 800-349-3839 • [email protected] • upliftdesk.com
Locking pins
(qty 4)
Drywall anchors
(qty 6)
Screws
(qty 6)
Washers
(qty 6)
Shelf panelTop panelMain panel
Step 1
Determine where you want the phone booth to be on your
wall.
Ensure there is enough room for the Main panel to unfold at.
Make a mark on the wall where you want the center of your
phone booth to be installed. We recommend making a mark
about 78” up from the oor to accommodate users up to 6’
3” tall.
Step 2
Have a friend hold the unfolded Main panel up to the wall,
aligning it with the top edge at the mark you made. The panel
should be the aligned the correct way: the at side should be
against the wall with the vertical notches facing outward, and
the edge with the large curved corners should be facing the
oor.
With your friend supporting the panel in place, use a level to
make sure the booth will be straight when installed. Then use a
pencil or a nail to make a mark on the wall through each of the
six holes of the Main panel.
Acoustic Phone Booth
ACU011
The hardware included is for attaching the booth to wood or drywall.
Other types of wall material may will require different hardware (not included).
A note before you begin:
Step 3
Remove the panel from the wall, and use a drill to make pilot
holes where your marks are.
For wood walls: Use a 1/8” drill bit to make pilot holes in each
of the six marked locations.
For drywall: Use a 1/8” drill bit to make pilot holes in each of
the six marked locations. Note: if you run into a wall stud when
drilling the pilot hole, do not use a Drywall anchor in that hole.
Use just a Screw and Washer instead.
Press the tip of one Drywall anchor into each pilot hole, and
using a Phillips-head screwdriver, screw the Anchors in until
they are ush with the surface of the wall. Be careful to not
overtighten the Drywall anchors
Package Contents

© UPLIFT Desk • 800-349-3839 • [email protected] • upliftdesk.com
Step 5
Once the Main panel is securely attached to the wall, press the
Shelf panel into the lower three slots at the back of the Main
panel. Be sure to align the side of the shelf with the two tabs
with the side of the Main panel that has the two slots that cor-
respond with it.
Next, press the three tabs on the Top panel of the phone booth
into the three slots at the top of the Main panel. Be sure the
at side with no tabs is facing the front and the correct color is
facing the inside of the phone booth.
Step 6
With one person supporting the Top panel, the other person
can fold one side of the Main panel into place, aligning the slots
with the tabs on the Shelf panel and Top panel.
Repeat the same process on the other side.
Step 7
Evenly press or tap the sides of the main panel into place until
there are no gaps between the Main panel sides, the Top panel,
and Shelf panel.
Two tabs will extend out from each of the left and right sides,
and will have a slot. Slide the Locking pins into those slots to
hold all of the panels securely together and to complete the
installation process.
AI-ACU011-1.0
Copyright Notice: This guide is a component of this UPLIFT Acoustic product. This guide is a part of the scope of delivery, even if the item is resold. This guide is also available on the UPLIFT Desk website: upliftdesk.com.
Excerpts or copies may not be forwarded to third parties or used in any other published form without the prior written consent of UPLIFT Desk. These instructions are subject to United States copyright law.
©
CAUTION: Read all instructions before assembly. Failure to assemble or install properly can re-
sult in damage or personal injury.
CAUTION: Do not lean on or place heavy objects on the phone booth shelf. It is designed only
to support lightweight items, such as notepads or cell phones.
CAUTION: Do not place or store objects on the top of the phone booth.
CAUTIONS & WARNINGS
!
!
!
!
Step 4
Have your friend hold up the Main panel of the phone booth
again to align the holes in the panel with the Anchors or pilot
holes. The at side of the Main panel should go against the
wall, and the side with the two long vertical notches at the
corner seams should be facing outward.
Pair up the Washers and Screws, and use them at each of the
six holes in the Main panel (we recommend starting on one of
the bottom holes, since they are easier to reach). Drive each
Screw until the Washer makes contact with the panel’s surface.
Do not overtighten.