Uplift Desk V2 4-Leg User manual

© UPLIFT Desk • 800-349-3839 • [email protected] • upliftdesk.com 1
Package Contents
V2 4-Leg Foot
(qty 2)
4mm Allen WrenchM6x12 Machine Screws
(qty 16)
V2 4-Leg Standing Desk
Foot Replacement Instructions
FRM582
Step 1
A. Remove all objects, accessories, and attached
components from desk since you will be inverting
it for this installation.
B. Press and hold the Down Button to bring the desk
to its lowest position, then unplug the desk from
the electrical outlet.
C. Priortoippingthedeskover,moveittoasuitable
area free from clutter or obstruction. We recom-
mend resting the desktop on a carpet or blanket.
Be aware of any cables or attached components
andsecurethembeforeippingthedesk.
• Note: When ipping the desk, always hold the
frame and the desktop together. Lifting by the
desktop only could put stress on improperly
fastened screws connecting the desktop to the
frame and may cause them to separate from the
frame if they were not attached properly.
D. You and a friend should each hold on to the rear
edge of the desktop with one hand and hold a leg
with the other hand.
E. Supporting both the desk frame and the desktop,
slowly tilt the desktop toward the rear of the desk
until the back edge of the desktop is resting on the
ground.
F. Hold onto the leg and the front edge of the desk-
top, then tilt the desk another 90 degrees until the
desk is upside down and resting on a carpet or
blanket.
Recommended Assembly Workspace & Practices
• Place all parts on a clean surface such as a rug or carpet to avoid scratches.
• Two or more people are recommended for assembly.
• Remove all packaging materials before beginning the assembly process.

© UPLIFT Desk • 800-349-3839 • [email protected] • upliftdesk.com2
Step 2
A. If your desk has casters installed and you plan to
use them with the new Feet, remove them from
each of the currently installed peg feet. You may
needa0.5”(13mm)atwrenchorthinadjustable
crescent wrench to remove the casters.
B. Using the included 4mm Allen Wrench, remove
each of the M6x14 Machine Screws that are hold-
ing the peg feet to the legs (four screws per peg
foot).
A. B.
Step 4
A. If you are replacing casters removed in Step 2,
rst remove the pre-installed leveling glides by
unscrewing them, no tool necessary.
B. Thread the casters into the Feet and use a 0.5”
(12mm)atwrenchtotighteneachcaster.
C. Ensure the casters are in the locked position be-
foreippingyourdeskuprightagaintoensurethe
deskdoesnotmoveasyouipitontothecast-
ers.Tolockthecasters,iptheleverattheback
of each caster to the down position (towards the
ceiling when the desk is upside down) and test the
wheel to make sure it does not turn.
Step 3
A. Place one of the new Feet on top of two legs on
one side of the desk, as shown, with the pre-in-
stalled leveling glides facing up.
B. Insert, but do not tighten, a M6x14mm Machine
Screw into each of the eight threaded holes.
• Note:Ifyouarehavingdifcultyaligningthe
holes in the Foot with the holes in the legs, use
the 4mm Allen Wrench to loosen, WITHOUT
REMOVING, the four screws that attach each
leg to the crossbar ends. Be sure to rmly
tighten these screws again once the Foot has
been fastened to the legs.
C. Once all eight screws have been started, tighten
them with the 4mm Allen Wrench.
D. Repeat the previous steps for the second new
Foot.
E. The desk frame screws can become loose over
time or may not have been completely tightened
during the initial assembly. Since the desk is upside
down, take the opportunity to ensure all frame
screws are tight using the 4mm Allen Wrench.

© UPLIFT Desk • 800-349-3839 • [email protected] • upliftdesk.com 3
Step 5
A. Withthehelpofafriend,ipthedeskupright.Re-
fer to Step 1 and reverse those instructions.
B. Move the desk back to its location.
• If you have casters installed, make sure the
casters are not locked and roll it to the loca-
tion.
• If you are using the pre-installed leveling
glides, carefully lift the desk with two or more
people and move it to its location - DO NOT
drag the desk as this may cause damage to
thedeskandoor.
C. Once the desk is in position, reinstall any accesso-
ries that had been removed and plug the power
cord back into the outlet.
D. Before use, perform the reset procedure below.
This is an important step.
Reset Procedure
Before using the desk, you must rst perform this
Reset Procedure:
• Press and hold the Down Button until the desk
stops at its lowest position, then release.
Note: On the Advance Paddle keypad, press
down on the paddle.
• Press and hold the down button again for 30
seconds, then release.
Note: On the Advance Paddle keypad, the
word “RESET” will appear at this point.
Note: On other UPLIFT keypads with display,
the letters “ASr” will appear at this point.
• Press and hold the Down Button one more time
until the desk lowers slightly, rises and stops,
then release the button. The reset is complete
and the desk is ready for use.
RESET

© UPLIFT Desk • 800-349-3839 • [email protected] • upliftdesk.com4
Copyright Notice: These instructions are a component of this product. These instructions are part of the scope of delivery, even if the item is resold. These instructions are also available on the UPLIFT Desk website: uplift-
desk.com. Excerpts or copies may not be forwarded to third parties or used in any other published form without the prior written consent of UPLIFT Desk. These instructions are subject to United States copyright law.
©
CAUTION: Read all instructions before assembly. Failure to assemble or operate properly may
result in damage or personal injury. Retain manual for future reference.
WARNING:Designedforuseindryworkenvironmentsonly.Riskofre,electricshock,orper-
sonal injury if used outdoors or in a damp location. Use only indoors.
WARNING: Make sure that the wires for your monitor and devices are not touching any obsta-
cles or walls and are an appropriate length to allow for full adjustment of the desk. Make sure
that no obstacles are in the full range of height adjustment.
WARNING: Only plug the desk into a properly grounded 120V outlet. Unplug the desk from the
electrical outlet before moving the desk or before adding/removing parts or accessories. Risk of
electric shock.
WARNING: Do not open any desk component or insert any object in a desk component. Risk of
electric shock.
WARNING: In case of spilled liquids, immediately unplug desk. Then clean spill with a dry cloth.
Risk of desk failure or electric shock if desk components become wet.
WARNING: Keep heated surfaces away from plug. Never use the desk with a damaged cord or
plug. Risk of electric shock. Call us for a free replacement cord.
WARNING:Keepngersandallbodypartsclearofthemovingdesk.Checksurroundingsonall
sides before using the desk to ensure there are no immobile obstacles within the desk’s range of
motion. Ensure all cords are the appropriate length so they don’t pull as the desk moves.
WARNING: Keep unsupervised children away from the desk. Before use, teach children about
desk safety with this manual. Risk of personal injury and electric shock if the desk is misused.
WARNING: This desk is height adjustable so that it may be positioned at a user’s ergonomic
height as described in this manual. Inappropriate use of this desk can cause property damage or
bodily injury. Under no circumstances does the manufacturer accept warranty or liability claims
for damages caused from improper use or handling of this desk. Provide this manual to any new
user.
WARNING: When relocating the unit, remove all devices to avoid harm or damage, and adjust
the unit to its lowest position.
WARNING: When relocating the unit, move it carefully with two people, to avoid injury and
damage to the product and surroundings.
CAUTIONS & WARNINGS
!
!
!
!
!
!
!
!
!
!
!
!
!
AI-FRM582-1.0