Uplift Desk Vert Ergonomic Chair CHR458 User manual

© UPLIFT Desk • 800-349-3839 • [email protected] • upliftdesk.com
(g. 01) (g. 02)
Allen wrench (L-shape)
Base
Casters
(qty 5)
Back
(with armrests)
M6x20 screw (qty 2)
Plastic cap (qty 2)
Outer cover
(optional)
Inner cover
(optional)
Note: may be pre-installed on Chair’s Back
Cylinder
Seat
Headrest
M8x20 screw (qty 3)
Flat washer (qty 3)
Step 1
Insert the Casters into the holes on the Base, and press them rmly
to secure them in place.
Flip the Base, Casters down, onto the oor and insert the Cylinder
into the Base in the orientation shown, with the smaller diameter
end up. Be cautious around the end of the Cylinder to prevent it
from getting oil on you or your clothes.
Step 2
Place the Seat upside down on the edge of a stable surface, such
as a table.
Line up the holes for the Back and the Seat. Have a friend help
keep it steady while you attach the Back to the Seat. Using the
Allen wrench, screw the Back and Seat into place using three
M8x20 screws and three Flat washers.
Note: These screws and washers may arrive partially inserted
into the Back, upon unboxing. Simply remove, and then attach
the Seat and Back together.
Step 3
Lower the chair assembly onto the Cylinder to secure it in place.
NOTE
If you don’t want to install the Headrest, take the Outer cover (a)
and Inner cover (b) and attach them as shown. These cover up
the places that the Headrest attaches.
If you want to install the Headrest, proceed to Step 4.
(a) (b)
Step 4
The Headrest ts into the Back in a specic way. Look for the
lower holes on the rubber portion of the headrest (g. 01) and the
recessed tab in the Back (g. 02). These two parts t together.
Angle the Headrest, as shown. Lining up the slot on the Headrest
with the tabs on the Back, tilt it forward rmly, tting the two
parts together.
Next, insert two M6x20 screws and tighten using the Allen wrench.
And nally, place the two Plastic caps over the screws.
Package Contents
Vert Ergonomic Chair
SKU: CHR458

© UPLIFT Desk • 800-349-3839 • [email protected] • upliftdesk.com
Seat Height
Adjust by twisting the lever on the right side of the seat. Stand
up to raise the chair higher or sit down in the chair to lower it.
Seat Depth
Adjust by pulling out the handle on the right side near the front
of the Seat. Slide the seat forward or backward to your preferred
position, then push the handle back in to lock it into place.
Adjustment Guide
Back Tilt Adjustment
To unlock the Back, move the lever on the left of the Seat into the
UP position. This allows the back to “free oat” with you as you
move and recline to any position you wish within the chair’s range
of recline. To lock the Back, move the lever into the DOWN position.
If you prefer the back to be stationary, angle the seat to your pre-
ferred position and twist the lever DOWN. This will lock the chair at
the closest preset angle. There are three preset positions.
To unlock the back again or to change positions, ip the lever back
and press back slightly in the chair to disengage the lock.
locked unlocked
Lumbar Height
To adjust the chair’s lumbar support, grab the tabs on either side
of the lumbar on the back of the chair and slide it to the position
that best supports your lumbar region.
Arm Height
Adjust by pressing the button underneath each armrest to un-
lock and gently move them up or down to the height that best
supports your arms.
Flexible Back
The Vert moves with you as you move throughout a variety of
positions. A exible back that mimics the spine allows the chair
to automatically adjust with your body for more supportive and
active seating.

© UPLIFT Desk • 800-349-3839 • [email protected] • upliftdesk.com
CAUTION: Read all instructions before assembly. Failure to assemble properly may result in
damage or personal injury.
WARNING: This product’s maximum weight capacity is 250 lbs. DO NOT exceed the maximum
weight capacity.
CAUTIONS & WARNINGS
!
!
!
Normal- Vacuum your fabric seat as needed. Vacuuming picks up dust and reduces the need for professional cleaning.
Ink Stains- Apply a small amount of isopropyl alcohol to a clean and damp absorbent cloth. Start at the outside of the ink
stain and work toward the center. Apply pressure, but do not rub too vigorously. As you work and your cloth soaks up
the ink from the fabric stain, it’s important to use a clean section of the cloth or the stain will spread. Apply more isopropyl
alcohol to the cloth as needed. If the ink stain persists, try using acetone. Note: This procedure is not intended for day-to-
day cleaning.
Spot Cleaning- Immediately soak up the stain with a soft, absorbent cloth. Do not dry the stain completely, as this may
set it in the fabric permanently. The longer a stain is allowed to remain on the fabric, the more difcult it is to remove.
Oil-based Stains- Use a dry cleaning solution applied with a damp clean cloth or sponge. Test the cleaning solution on a
small, concealed spot on the fabric rst before attempting on a larger area. If there is no spotting, ringing, or damage to
the fabric or its dyes, apply the cleaning solution to the soiled area with light, quick strokes. Begin at the outside of the
stain and work toward the middle, making sure you use a clean part of the cloth as you work.
Water-based Stains- Use a water-based fabric cleaner (specically made for cleaning fabric) or a solution of mild, alkaline,
warm soapy water. Make sure that the soap and water mixture is not overly soapy. Test on a small, concealed section
of the fabric rst before applying to the main area. Work the cleaner or soap/water mixture into the stain on the fabric,
starting from the outside of the fabric and working your way to the middle.
*A note about fabric care

512-614-3152
800-349-3839
[email protected]
upliftdesk.com
Work Better. Live Healthier
Copyright Notice: This guide is a component of the UPLIFT Vert Chair. This guide is a part of the scope of delivery, even if the item is resold. This guide
is also available on the UPLIFT Desk website: upliftdesk.com. Excerpts or copies may not be forwarded to third parties or used in any other published
form without the prior written consent of UPLIFT Desk. These instructions are subject to United States copyright law.
©
®
AI-CHR458-3.1