Uplift Desk KBT002 User manual

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
Step 1
Take the Track and place underneath your desktop, in order to gure out
which size to use (11’’ or 21’’ Track) and where to place it. If there are pre-
drilled holes in your desktop, line the track up with the holes. If there are
not pre-driled holes, drill your own pilot holes using 1/8’’ diameter drill bit
and drill 1/2’’ deep. Be sure to leave about 1/2” from the front of the desk.
Use eight (8) Wood screws to attach the 21’’ track, and six (6) Wood
screws to attach the 11’’ track to the desktop. Use one (1) more screw to at-
tach the Rear bumper as shown.
Step 2
With the desk right side up, line up the mechanism with the grooves on the
track and slide it in.
Please note: the mechanism will not adjust up or down until the tray has
been attached and the shipping pin is removed (see steps 3 and 4).
Step 3
Attach the Bamboo tray to the mechanism by lining up the holes in the
tray with the holes on the mechanism, and secure by inserting the four (4)
Machine screws through the holes, and screwing the four (4) Acorn nuts
onto them from below.
KBT002/R01
®
Large Bamboo Keyboard Tray
KBT002
Caution:
When using screws on a desktop with a center-cut ergo edge, take care to
ensure that the screw is not close to the ergo edge to avoid piercing the
desktop with the screw. (see g. 1)
g 1.
Adhesive pads
(optional. qty 4)
Wood screws
(qty 12)
Front bumper
Back bumper
Acorn nut
(qty 4)
Cord catcher
Mousepad
Mechanism
Track
(11’’ and 21’’ tracks are included.)
Package Contents:
Bamboo tray
Wrist support
Track Spacer Kit
(optional. sold separately)
*A note before you begin:
Determine where to mount the Keyboard tray. If you need to mount it
over the Crossbars of your desk AND you ordered the optional Track
Spacer Kit, open the box containing the Track Spacer Kit and follow
those instructions inside.
Wire clip

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
Step 5
Finally, lower the tray, slide it back on the track and install the front
bumper using three (3) Wood screws.
Step 6
Attach the foam palm support onto the front of the Bamboo tray. Place the
mousepad and cord catcher to the desired side.
The non-slip Adhesive pads can be placed over the heads of the machine
screws, or in any other position on the board.
Use the Wire clip anywhere to secure loose wires to prevent snags.
Rotate
The Keyboard Tray rotates at the point where the mechanism attaches to the
Track. It can rotate 360 degrees.
360°
Copyright Notice: This guide is a component of the UPLIFT Desk Large Bamboo Keyboard Tray. This guide is a part of the scope of delivery, even if the item is resold. This guide is also available on the UPLIFT Desk website:
upliftdesk.com. Excerpts or copies may not be forwarded to third parties or used in any other published form without the prior written consent of UPLIFT Desk. These instructions are subject to United States copyright law.
©
!CAUTION: Read all instructions before assembly. Failure to assemble properly may
result in product damage or injury.
Tilt
To adjust the tilt of the tray, turn the knob at the center of the tray.
Height
To adjust the height of the tray up and down, push down on the back of the
tray while lifting the front.
Adjustment Guide
Step 4
Lift up on the front of the tray and lower the back to relieve pressure on
the shipping pin and remove it.