Uplift Desk UDA115 User manual

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
®
E7 Electric Standing Desk Converter Instructions
UDA115
UDA115/R0190.014.01.0500v.C
Package contents
Flat head screws
(M6x14; qty 8)
Pan head screws
(M6x14; qty 2)
VESA mount
VESA bracket
Slot cover
Keypad
Power cable
Connecting cable
Base Lifting
column
Housing Keyboard tray
bracket
Keyboard tray
Worksurface
Worksurface
bracket
Pan head screws
(#10-24x5/8’’; qty 13)
Keypad
Power cable
Connecting
cable
Pan head screws
(M6x10; qty 4)
Pan head screws
(M4x12; qty 4)
VESA screw
(qty 1)
Cable clips
(qty 2)
Step 1
Place the base on your desk, with the front lined up with the front edge
of your desk. First (a) Attach the Lifting column to the Base using four (4)
M6x14 Flat head screws. Make sure the vertical column is facing towards
the front. Next, (b) Attach the Worksurface bracket to the front of the
Lifting column using four (4) M6x10 Pan head screws.
Step 2
Plug the Lifting column’s cable into the Connecting cable, and plug the
Connecting cable into the Control box. Also, plug the Keypad and Power
cable into the Control box, and nally plug the Power cable into a 120
Vac wall outlet. Press the “up” arrow on the Keypad to raise the Work-
surface to a higher level for Steps 3 and 4.
Note: If surface does not rise perform the reset instructions
in the TROUBLESHOOTING section on page 4.
Step 3
Unplug the Keypad only! Feed the end of the Keypad’s wire through
the top side of the Worksurface and t the Keypad into the pocket as
shown. Press Keypad cable into the wire channel on the underside of
the Worksurface. Attach Worksurface onto the Worksurface bracket
using ve (5) #10-24x5/8’’ Pan head screws. Plug the Keypad back into
the Control box.
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
[x] POWER CABLE [x] CONNECTING CABLE (get from FRM200 instructions)
VESA screw
#10-24x1/2’’ Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
[x] POWER CABLE [x] CONNECTING CABLE (get from FRM200 instructions)
VESA screw
#10-24x1/2’’ Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
(a)
(a) (b)
(b)
Step 4
Attach the Keyboard tray bracket to the Worksurface using four (4) #10-
24x5/8’’ Pan head screws. Then attach the Keyboard tray to the Keyboard
tray bracket also using four (4) #10-24x5/8’’ Pan head screws.
Caution: Make sure that Keyboard tray of the assembled unit is clear of the
desk edge. When the unit is at it’s lowest position, the Keyboard tray will be
lower than the desk’s surface.
Step 5
Take a moment to group your wires tightly together, to prevent them from
splaying too widely, getting caught in moving parts, or interfering in Step 6.
We recommend using the two (2) Cable clips with adhesive here:
(a) Above the Control box to keep the Power cord close to the Lifting
column. For additional securing, the cable can run behind the Control box.
(b) About 2’’ below the Control box, on the top segment of the lifting column
(as shown). Leave slack to allow the lifting column to rise all the way up.

Step 6
Press the down button on the Keypad and lower the unit down to lowest
setting. Slide the Housing over the Lifting column.
Caution: As you slide on the Housing, be mindful of where the cables are.
Make sure the screw holes on the Housing match up with the screw holes
on the Lifting column and attach using four (4) M6x14 Flat head screws.
Step 7
(a) Attach the VESA bracket to the Lifting column using two (2)
M6x14 Pan head screws. Note, there are ve (5) different height set-
tings, choose the height that is best suited for your monitor.
(b) Attach VESA mount to your Monitor using the four (4) M4x12 Pan
head screws. Ensure that the hooks on the VESA mount are facing
down towards the bottom of the Monitor as shown.
(c) Then hook the Monitor assembly to the VESA bracket, and secure
with the VESA screw which is provided with the VESA mount.
(d) If you are not attaching a single or dual VESA mount to your
UDA115 lifting column, you may attach the Slot cover with the
two (2) M6x14 Pan head screws provided.
(monitor not pictured)
UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
KEYPAD LOCK
The keypad can be locked to prevent accidental activation or movement of the unit.
To lock: Press and hold “M” button until display changes to “LOC”
To unlock: Press and hold “M” button until display changes to numeric height setting.
NOTE: If a power outage occurs, the program will automatically return to the unlocked setting.
These programming instructions are compatible only with the Keypad that is included in this package,
and the Control box (on the Lifting column) with the following numbers located on the silver sticker:
MEMORY SETTINGS
Save up to two commonly used heights and recall them quickly.
l. Press the UP or DOWN button to move the unit to the desired height.
2. Press the “M” button.
3. Press the “1 or 2” button to assign the current height to a number on the keypad.
4. To recall any of those heights, press the numbered button to bring unit to assigned height.
6. PROGRAMMING
Single-column riser: 99.039.14.0333
HEIGHT CALIBRATION
Make sure the numeric display matches the actual height of the worksurface at its lowest position.
1. Press the DOWN button until the desk reaches the lowest position.
2. Measure the height from the oor to the underside of the worksurface. If the displayed height
does not match your measurement, follow the next steps.
3. Press the DOWN button until display ashes “RST”.
4. Press the “M” button until the numeric display begins ashing.
5. Press the UP or DOWN button to set unit to the measured height.
6. Once display changes back to “RST”, press the DOWN button until the unit lowers slightly, then
rises slightly and the display changes back to the numeric height setting.
*Note: “RST” will look like
“ASr” on the display
[x] POWER CABLE
[x] CONNECTING CABLE
(get from FRM200 instructions)
VESA screw
#10-24x1/2’’
Pan Head
M5x10
Pan Head
M6x10
Flat Head
Socket cap
(a) (b) (c)
(d)

UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
CONSTANT-TOUCH & ONE-TOUCH
These steps allow the unit to be set to either One-Touch or Constant-Touch. One-Touch requires only
a single touch of the “1 or 2” button to move the unit to a preset memory location. Constant-Touch
requires a continuous touch of the “1 or 2” button to move the unit to a preset memory location.
Constant-Touch is the default setting.
Change between One-Touch and Constant-Touch:
l. Press the DOWN button until the unit reaches the lowest position.
2. Press the DOWN button again until display ashes “RST”.
3. Press the “1” button until display shows “10.1” (One-Touch) or “10.2” (Constant-Touch)
and goes back to “RST”.
Note: While “RST” is still ashing, you can press the “1” button as many times as you’d like
to toggle between the two settings.
4. Press the DOWN button until the unit lowers slightly, then rises slightly and the display
changes back to the numeric height setting.
MINIMUM & MAXIMUM HEIGHT SETTINGS
The unit ships defaulted to its minimum and maximum height limits. These steps allow the upper
and lower limits to be adjusted to your preference.
Note: If memory settings were previously set outside of the new minimum and maximum height
settings, they will default to the new minimum and maximum settings. To set new minimum and
maximum height settings outside of the current settings, you will need to rst remove the current
minimum and maximum settings.
DISPLAY UNITS
Change the numeric display to show heights in either inches or centimeters.
l. Press the DOWN button until the unit reaches the lowest position. Release button.
2. Press the DOWN button until display ashes “RST”.
3. Press the “2” button until display shows “10.3” (centimeters) or “10.4” (inches) and goes
back to “RST”.
Note: While “RST” is still ashing, you can press the “2” button as many times as you’d like
to toggle between the two settings.
4. Press the DOWN button until the unit lowers slightly, then rises slightly and the display
changes back to the numeric height setting.
6. PROGRAMMING (continued):
To Set a new maximum desk height:
l. Press the UP or DOWN button to move the unit to the desired maximum height.
2. Press the “M” button once, and then the UP button once (the display will show “S-”).
3. Press and hold the “M” button until the Display shows “999”,
and then changes to numeric value of new upper limit.
To Set a new minimum desk height:
l. Press the UP or DOWN button to move the unit to the desired minimum height.
2. Press the “M” button once, and then the DOWN button once (the display will show “S-”).
3. Press and hold the “M” button until the Display shows “000”
and then changes to numeric value of new lower limit.
Removing adjusted maximum and minimum heights:
l. Press the “M” button (the display will show “S-”).
2. Press the “M” button again until the display shows “555”
and changes to the current numeric height setting.

UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
Copyright Notice: These instructions are a component of the UPLIFT Desk E7 Electric Standing Desk Converter. These instructions are part of the scope of delivery, even if the item is resold. These instructions
are also available on the UPLIFT Desk website: upliftdesk.com. Excerpts or copies may not be forwarded to third parties or used in any other published form without the prior written consent of UPLIFT Desk.
These instructions are subject to United States copyright law.
©
CAUTION:
Read all instructions before assembly. Failure to assemble properly may result in
damage or personal injury.
WARNING: Keep hands clear of the column while it is rising and falling. Do not touch it.
CAUTION: The maximum load capacity of the unit is 110 lbs. Do not overload.
CAUTION: Keep devices centered and away from the edge of the main worksurface,
to prevent them from falling.
CAUTION: Make sure that the wires for your monitor and devices have enough slack to prevent
your devices from being pulled off the unit workstation when raising the unit.
CAUTION: When relocating the unit, remove all devices to avoid harm or damage,
and adjust the unit to its lowest position.
CAUTION: When relocating the unit, move it carefully with two people, to avoid injury and
damage to the product and surroundings.
CAUTIONS & WARNINGS
!
!
!
!
!
!
!
!
If the unit does not respond when trying to raise or lower it, or if the Keypad displays error messages (“Er1”
through “Er13”) check to make sure all the cables are secure (Lifting column to cable, cables to control
box). If the problem persists, perform the reset procedure below.
- Reset Instructions -
1- Unplug the power cord and hold the DOWN button for 30 seconds.
2- Plug the power cord back in.
3- Press and hold the DOWN button on the Keypad until the unit reaches its lowest height.
Release the DOWN button. Press and hold the DOWN button again until
the LED display reads “RST” (about 10 seconds). Release the DOWN
button. Press and hold the DOWN button again until the unit lowers a
little bit more, slightly rises and stops. Release the DOWN button.
It is now ready to use.
4- The Keypad will then display the current height, and you should be able to operate it now.
5- You may need to do this if the unit is ever unplugged or loses power.
If the error messages persist after the reset procedure, stop the reset procedure and contact The Human
Solution (800.531.3746 or [email protected]).
If the Keypad displays “HO1”, then it is hot. Let the base cool down for 20 minutes.
*Note: “RST” will look like
“ASr” on the display
6. PROGRAMMING (continued):
7. TROUBLESHOOTING
ANTI-COLLISION SENSITIVITY
The unit has an Anti-Collision Sensitivity that will stop its movement if it hits something on the way down
or up. You can change this Sensitivity level by doing the following:
l. Press the DOWN button until the unit reaches the lowest position. Release button.
2. Press the DOWN button until display ashes “RST”.
3. Press the UP button until display shows “10.5”, “10.6”, or “10.7” and goes back to “RST”.
“10.5” is code for the 10 kg (22 lbs) setting (most sensitive setting, false positives are
sometimes possible).
“10.6” is code for the 15 kg (33 lbs) setting
“10.7” is code for the 20 kg (44 lbs) setting (least sensitive setting).
Note: While “RST” is still ashing, you can press the UP button as many times as you’d like
to toggle between the three settings.
4. Press the DOWN button until the unit lowers slightly, then rises slightly and the display
changes back to the numeric height setting.