URBAN OUTFITTERS Jenavive User manual

Assembly Instructions
Jenavive Bedframe
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights.
Any unauthorized reproduction, adaptation, distribution orother infringement will be prosecuted. Page 1 of 5
M) Allen Key
[M5 x 80mm] x1
J) Spring Washer
[Φ14mm] x28
L) Screw
[Φ4 x 30mm] x51
C) Center
Rail
x1
E) Middle Legs
x3
I) Bolt
[5/16’’ x 30mm] x28
G) Slat Roll
x1
B) Side Rail
x2
K) Flat Washer
[Φ16mm] x28
A) Headboard / Footboard
x2
F) Side Legs
x4
H) Corner Brace
x4
D) Middle Legs
x3
TOOLS REQUIRED BUT NOT INCUDED:
Phillips head screwdriver / drill
WARNINGS:
Do not throw away packing materials and carton until after assembly.
Assemble all parts on a clean smooth surface
CARE INSTRUCTIONS:
Avoid direct exposure to sunlight.
Do not place over heat or air conditioning vents.
Adjust levelers so that the furniture sits flat on uneven floors.
Blot spills do not rub, with a clean white cloth.
Do not use harsh chemicals.
Before cleaning any part test a small spot in a hidden area.
You may need to re-tighten all bolts after initial use.
PARTS INCLUDED:
URBAN OUTFITTERS

EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights.
Any unauthorized reproduction, adaptation, distribution orother infringement will be prosecuted. Page 2 of 5
URBAN OUTFITTERS
Assembly Instructions
Jenavive Bedframe
STEP 1
Insert the Bolts (I) through the Spring washers (J) and Flat washers (K) and into the Head board / Foot board (A).
Partially tighten with the Allen Key (M) leaving room to hang the brackets attached to the Side rails (B). Hang the
Side rails (B) on the Bolts (I) as shown then fully tighten all bolts.
STEP 2
Align the Corner braces (H) as shown and insert the bolts (I) through the Spring washers (J) and Flat washers (K)
and into the Head board / Foot board (A) and Side rails (B). Partially tighten the Bolts (I) with the Allen Key (M)
then tighten all bolts fully.
I
J
M
K
M
I
J
K
H

EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights.
Any unauthorized reproduction, adaptation, distribution orother infringement will be prosecuted. Page 3 of 5
OPTION 1 - High slat height
Assembly Instructions
Jenavive Bedframe
STEP 3
With help, lift the bed and screw in the Side legs (F).
STEP 4
Screw the Middle legs (D&E) together and then into the Center rail (C) as shown. Align the holes in the Center rail (C)
brackets with the holes in the Head board / Foot board (A). Insert the bolts (I) through the Spring washers (J) and
Flat washers (K) and into the Head board / Foot board (A). Partially tighten the Bolts (I) with the Allen Key (M) then
tighten all bolts fully. Ensure the wood rails bolted to the Side rails (B) are at the same height as the Center rail (C).
To raise the wooden rails, remove the bolts and re-attach the rails in the upper position with the Allen key (M).
K
F
H
C
D
E
M
I
J

EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights.
Any unauthorized reproduction, adaptation, distribution orother infringement will be prosecuted. Page 4of 5
URBAN OUTFITTERS
OPTION 2 - Low slat height
Assembly Instructions
Jenavive Bedframe
STEP 5
Screw the Middle legs (E) together and then into the Center rail (C) as shown. Align the holes in the Center rail (C)
brackets with the holes in the Head board / Foot board (A). Insert the bolts (I) through the Spring washers (J) and
Flat washers (K) and into the Head board / Foot board (A). Partially tighten the Bolts (I) with the Allen Key (M) then
tighten all bolts fully. Ensure the wood rails bolted to the Side rails (B) are at the same height as the Center rail (C).
To lower the wooden rails, remove the bolts and re-attach the rails in the lower position with the Allen key (M).
STEP 6
Ensure all the bolts are tightened then with help, unroll the Slat roll (G) onto the partially assembled bed frame.
Ensure the blocks at either end of the Slat rail (G) lock in between the the last two slats on either end of the roll.
Secure with screws (L) and a Phillips head screwdriver or drill (not included).
E
C
M
I
J
K
G
L

EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights.
Any unauthorized reproduction, adaptation, distribution orother infringement will be prosecuted. Page 5 of 5
Finish -Higher Slat Height
URBAN OUTFITTERS
Finish -Lower Slat Height
Assembly Instructions
Jenavive Bedframe