URBAN OUTFITTERS Felix User manual

EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights.
Any unauthorized reproduction, adaptation, distribution or other infringement will be prosecuted. Page 1 of 6
G) Door
x1
H) Door
x1
K) Top Rail
x2
I) Base Sides
x2
J) Bottom Rail
x2
a) Cam Bolt
[M6x35mm] x6pcs b) Cam Lock
[Ø15x12mm] x6pcs [Ø7.8x30mm] x12pcs
c)Wooden Dowel f )
g) Screw
[M3.5x14mm] x14pcs
d) Bolt
[M7x38mm] x6pcs
h) Bolt
[M6x35mm] x8pcs
i ) Bolt
[M6x25mm] x6pcs
Pivot Pin
4pcs
Strap
1pc Wall Plug
1pc
k) Allen key
1pc
e) Washer
2pcs
j) Rebounder
2pcs l) Wedge
8pcs
m) Screw
[M4x12mm] x1pc
n) o) p) Screw
[M4x35mm] x1pc
102cm
36cm
74.8cm
Felix Media Console
Assembly Instructions
TOOLS REQUIRED BUT NOT INCLUDED:
Phillips Head Screwdriver
Pencil
WARNING:
Install the anti-tip kit shown in step 10 to ensure safety.
Do not throw away packing materials and carton until after assembly.
Assemble all parts on a clean smooth surface
CARE INSTRUCTIONS:
Avoid direct exposure to sunlight. Do not place overheat or air conditioning
vents. Adjust levelers so that the furniture sits flat on uneven floors.
Blot spills do not rub, with a clean white cloth.
Do not use harsh chemicals.
Before cleaning any part test a small spot in a hidden area.
You may need to re-tighten all bolts after initial use.
PARTS INCLUDED
A) Top Panel
x1
B) Bottom Panel
x1
C)Side Panel
x1
D)Side Panel
x1
E) Middle Panel
x1
F) Back Panel
x1

EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights.
Any unauthorized reproduction, adaptation, distribution or other infringement will be prosecuted. Page 2 of 6
STEP 1
Insert the pivot pins (f) into the pre-drilled holes on the top and bottom of the Doors (G&H)
a
a
a
a
a
am
na
gx4
j1x2
j2x2
j1 j1
g
eg
f f
ff
e
g
G H
eg
f f
f
e
g
G H
g
A
f
a
a
am
na
j1 j1
g
g
A
FRONT
FRONT
ex2
fx4
gx2
ax6
jx2
gx4
nx1
mx1
Felix Media Console
Assembly Instructions
STEP 2
Detach the re-bounders (j2) from their bases (j1). Align the bases (j1) to the pre-drilled holes in the
Top Panel (A) as shown. Screw the cam-bolts (a) into the pre-drilled holes in the Top Panel (A) as
shown. Align the strap (n) to the back of the Top Panel (A) as shown. Insert screw (m) and tighten
with a Phillips head screwdriver (not provided).

EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights.
Any unauthorized reproduction, adaptation, distribution or other infringement will be prosecuted. Page 3 of 6
D
C
E
A
F
F
b
b
b
b
b
b
c
cc
cc
c
bx6
cx6
k
d
d
d
d
d
dB
c
c
c
c
cc
cx6
dx6
Felix Media Console
Assembly Instructions
STEP 3
Insert the dowels (c) into the holes in the edge of the Sides Panels (D&C) and Middle Panel (E). Place
the Side Panels (D&C) and Middle Panel (E) onto the cam-bolts (a) attached to the Top Panel (A) as
shown. Slide the Back Panels (F) into the grooves on the Side Panels (D&C), Middle Panel (E) and Top
Panel (A) Insert the cam-locks (b) into the holes in the Side Panels (D&C) and Middle Panel (E) as
shown. Tighten with Phillips head screwdriver (not provided) as shown.
STEP 4
Insert the dowels (c) into the holes in the edge of the Sides Panels (D&C) and Middle Panel (E). Place
the Bottom Panel (B) onto the dowels in the partially assembled case. Insert the screws (d) into the case
and tighten with the Allen key (k) to complete the assembly of the case.
[CASE SHOWN
UPSIDE DOWN]
[CASE SHOWN
UPSIDE DOWN]
D
C
E

EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights.
Any unauthorized reproduction, adaptation, distribution or other infringement will be prosecuted. Page 4 of 6
g
gl
l
l
l
l
l
l
l
l
g
g
g
g
g
g
g
h
h
h
h
h
h
h
h
I
I
J
J
K
K
B
gx8
lx8
hx8
Felix Media Console
Assembly Instructions
STEP 7
Insert the wedges (i) into the groove in the back of the cabinet as shown. Insert screws (g) into the
wedges (i) and tighten with a Phillips head screwdriver (not provided).
STEP 8
Align the Base Sides (J) with the Top & Bottom Rails (K&I) as shown. Note that the holes in the Top
Rails (K) should face up during assembly. Insert the bolts (h) through the Base Sides (J) and tighten
with the Allen key (k) to complete assembly of the base.
[BASE SHOWN
UPSIDE DOWN]
[CASE SHOWN
UPSIDE DOWN]

G
H
BK
K
J
J
i
i
i
i
i
i
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights.
Any unauthorized reproduction, adaptation, distribution or other infringement will be prosecuted. Page 5 of 6
ix6
Felix Media Console
Assembly Instructions
STEP 8
Place the base on the case as shown. Insert the bolts (i) and tighten with Allen key (k)
STEP 9
Flip assembly upright and carefully insert the Doors (G) as shown to complete the assembly of the
Media Console. Adjust re-bounders (j) by unscrewing the tip.
[CASE & BASE
SHOWN UPSIDE
DOWN]

12
Wall
ox1
px1
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights.
Any unauthorized reproduction, adaptation, distribution or other infringement will be prosecuted. Page 6 of 6
n
po
STEP 10
Place the Media Console in its desired position slightly away from the wall. Place the end of the strap
(n) on the wall above the bottom of the cabinet and mark the wall through the hole in the strap (n). If
drilling into drywall, pre-drill for the plastic anchor (o) at the marked location and insert the anchor (o).
Place the end of the strap back on the wall above the plastic anchor and insert screw (p) . If drilling
into a stud, you do not need to use the plastic anchor. Use a stud finder to determine the location of
studs within your wall.
Felix Media Console
Assembly Instructions