URBAN OUTFITTERS MINIMALIST 68968148 User manual

EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights.
Any unauthorized reproduction, adaptation, distribution or other infringement will be prosecuted.
Page 1 of 6
1) Head and Foot Rail x2
(Wrapped in green tape)
2) Side Rail x2
(Wrapped in green tape)
(3) Center Support x1 (Wrapped
in green tape)
(4) Center Leg 3x (Wrapped
in green tape)
(5) Slats 2x
(Wrapped in green tape)
A) Allen Bolt
[8mm x 20mm] x8
C) Allen Bolt
[8mm x 65mm] x5
(D) Allen Key
[5mm] x1
MINIMALIST PLINTHE BED
Assembly Instructions
TOOLS REQUIRED BUT NOT INCUDED:
Phillips head screwdriver
Do not throw away packing materials and carton until after assembly.
Assemble all parts on a clean smooth surface
CARE INSTRUCTIONS:
Avoid direct exposure to sunlight. Do not place over heat or air conditioning vents.
Adjust levelers so that the furniture sits flat on uneven floors.
Blot spills do not rub, with a clean white cloth.
Do not use harsh chemicals.
Before cleaning any part test a small spot in a hidden area.
You may need to re-tighten all bolts after initial use.
PARTS INCLUDED:
B) Washer
[8mm x 17mm] x8

EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights.
Any unauthorized reproduction, adaptation, distribution or other infringement will be prosecuted.
Page 2 of 6
5
1
2
3
4
2
1
EXPLODED & LABELED
MINIMALIST PLINTHE BED
Assembly Instructions

EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights.
Any unauthorized reproduction, adaptation, distribution or other infringement will be prosecuted.
Page 3 of 6
1
Note: Match the labels on
components before
assembly, e.g. Label A on
Head and Foot Rail to
2 Label A on Side Rail.
B A
D
B A
B
A
D
A B
2
A B
1
2
1D
A
B
D
20MM
20MM
17MM
STEP 1
Place the head and foot rails (1) upright on a clean smooth surface such as carpet or cardboard.
Place top front frame (1) into side framing (2) as shown in the sketch below. Insert Allen Bolts (A)
with Washer (B) through frame then tighten with Allen key (E).
MINIMALIST PLINTHE BED
Assembly Instructions

© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights.
Any unauthorized reproduction, adaptation, distribution or other infringement will be prosecuted.
Page 4 of 6
1
D
C
1
3
3
1D 2
C
C
D
C
3
C
4
C
2
D
3 C 1
4 3
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
4
65MM
MINIMALIST PLINTHE BED
Assembly Instructions
STEP 2
Align the Center Rail (3) as shown. Insert Bolt (D). Tighten with supplied Allen Key (D). Align Center Legs (4)
and insert Bolt (D). Tighten with supplied Allen Key (D).

EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights.
Any unauthorized reproduction, adaptation, distribution or other infringement will be prosecuted.
Page 5 of 6
5
1
2
3
4
2
1
MINIMALIST PLINTHE BED
Assembly Instructions
STEP 3
Place the slat sets (5) on the assembled frame. The front and back slat should be positioned
so that the wood blocks on either end of the side frame (2) and center frame (3) fit inside the
slat set - this will keep the slat sets in position.

EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights.
Any unauthorized reproduction, adaptation, distribution or other infringement will be prosecuted.
Page 6 of 6
29.5”
9.5”
6”
3.5
83”
63”
ASSEMBLED
MINIMALIST PLINTHE BED
Assembly Instructions