URBAN OUTFITTERS ALONZO 69500866 User manual

ALONZO BOOKSHELF
Assembly Instructions
TOOLS REQUIRED BUT NOT INCLUDED:
(Not Applicable)
Do not throw away packing materials and carton until after
assembly. Assemble all parts on a clean smooth surface.
CARE INSTRUCTION:
Avoid direct exposure to sunlight. Do not place overheat or air conditioning
vents. Adjust levelers so that the furniture sits flat on uneven floors.
Blot spills do not rub, with a clean white cloth.
Do not use harsh chemicals.
Before cleaning any part test a small spot in a hidden area.
You may need to re-tighten all bolts after initial use.
PARTS INCLUDED
A) OUTSIDE LEG
x2
E) MIDDLE SHELVES
x2
B) INSIDE LEG
x2
G) ALLEN BOLT ROUND HEAD
[M8 x 40mm] x20
C) TOP SHELVES
x2
F) BOTTOM SHELF
x1
H) WASHER
[20mm] x20
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights.
Any unauthorized reproduction, adaptation, distribution or other infringement will be prosecuted.
D) LEFT / RIGHT SHELVES
x4
�
I) ALLEN KEY
[5mm] x1
Page 1 of 2

ALONZO BOOKSHELF
Assembly Instructions
STEP 1
PLACE THE BOTTOM SHELF (F) INTO THE LEGS (A&B) AS SHOWN. INSERT SCREWS (G) INTO WASHERS (H) AND
INTO LEGS. TIGHTEN WITH ALLEN KEY (I). REPEAT FOR ADDITIONAL SHELVES MOVING UP FROM BOTTOM.
/
FINAL
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights.
Any unauthorized reproduction, adaptation, distribution or other infringement will be prosecuted.
Page 2 of 2
BOTTOM
SHELF (x1)
MIDDLE
SHELVES (x2)
OUTSIDE
SHELVES (x4)
TOP
SHELVES (x2)
INSIDE LEGS (X2)
OUTSIDE LEGS (X2)

A
B
D
E
4x Bracket
4x Long Screw
2x Strap
4x Wall Plug
Warning - Children may be injured by tipping of furniture and the use of the Anti-Tip Kit is highly recommended .
This Anti-Tip kit is only a deterrent. It is not a substitute for proper adult supervision. Manufacture and retailer assume no
liability for improper installation or excess loads placed on screws, brackets, or straps. When properly installed, this restraint
provides protection against unexpected tipping of furniture. This Anti-Tip kit MUST be installed into the wall using proper
mounting hardware OR into a wall stud using appropriate screws. Position of the Anti -Tip Kit depends on the products and
the location of the wall studs. The hardware provided is not a comprehensive solution for wall types.
Be sure to consult a professional or your local hardware store to determine the hardware needed for your specific wall type
(plaster, drywall, concrete) etc.
Using a second person to assist you, place the unit in the desired final location against a wall .it is suggested to use a stud
finder to find wall stud along the width of the unit and roughly 1 inch below the top of the unit. Where possible, mark a drill
Hole position on the wall where there is a stud and use a drill or screwdriver (NOT INCLUDED) to attach wall brackets (A)
to the wall using long screws (B) in the location of the wall studs.
In a case where there is no wall stud, hold brackets (A) on wall and mark the drill hole positions so that they are roughly 1
inch below the top of the piece. using a drill with a drill bit roughly the diameter of the plastic wall plugs (D), Drill pilot holes
in marked positions. Insert the plastic wall plugs (D) into the holes until the tops are roughly flush with the wall. Align the
holes and insert the long screws (B) through brackets (A) and into the corresponding holes in the wall using a Phillips head
screw driver ( NOT INCLUDED).
IMPORTANT: Check that the wall bracket is firmly screwed into the wall and the cable Tie is snug. If there is any hesitation,
please consult a professional or your local hardware store.
Bracket (A)
Dry Wall
Long Screw With Wall
Plug (B,E)
Strap(C)
Figure A
Figure C
Figure B
C4x Small Screw
Bracket (A) Small Screw (C)
ANTI-TIP HARDWARE
Assembly Instructions
PARTS INCLUDED: