URBANGLIDE RIDE 81 BOOST User manual

RIDE 81 BOOST
« Translation of the original instructions »
URBANGLIDE is a brand imported by the company PACT INFORMATIQUE, located at
33 rue du Ballon –93160 Noisy Le Grand –France

ENGLISH 1
FRANCAIS 10
ESPAÑOL 28
PORTUGUÊS 46
ITALIEN 48
NEERLANDAIS 60
ALLEMAND 81

SUMMARY
SAFETY AND PRECAUTION
Protective equipment 1
Driver’s advice 1
Procedures and driving conditions 1
Usage of the charger 2
Battery 3
Maintenance 3
Transport 3
Using the scooter 3
Rebus 4
PRODUCT PRESENTATION AND DETAILS
Parts name 5
Fold/Unfold the product 6
Using the screen 7
Advanced setting 7
HOW TO USE

1
SAFETY AND PRECAUTION
Please read the manual carefully before using the product and read the risks and safety
tips in the manual. The use of an electrical product can be dangerous if the user is not
watchful. Misuse and non-respect with the safety instructions does not affect the
company in event of accident. Self-judgment and common sense are necessary for
users to detect the possible dangers.
Please verify the current regulations and laws in your country to know where and how
to use your product legally. You must comply with the rules and laws that applicable to
vehicles and pedestrians.
•Protective equipment
Always wear the following protective equipment:
-Approved and certified helmet according to your location
-Knee pads and elbow patches
-Long sleeve t-shirt and long pants
-Gloves
-Shoes with rubber soles, never drive in barefoot or sandal. Verify to make the
laces made and keep them as far as possible from the wheels and the internal
system.
•Driver’s advice
This device may be used by children over 8 years of age and by persons with reduced
physical, sensory or mental capabilities or lack of experience or knowledge, if properly
supervised, or if instructions for use of safely, were given to them and the risks were
apprehended. Children under 8 must not play with the product. Cleaning and user
maintenance should not be performed by unattended children. Do not touch the engine
or the brakes of the product immediately after use, these parts may be extremely hot.
The maximum weight of use is 100 kg.
Procedures and driving conditions
Please verify the current laws and rules in your country before using the product. Look
around when using the product and pay attention to all possible risks. It is important to
respect the rights and properties of everyone. For your safety do not start the
accelerator if you are not on the product. This product is not designed to make jumps,
acrobatic tricks and skids.
Never drive on roads, near vehicles, stairs, hills, swimming pools or other streams.
Please hold the handlebars with both hands. Never go on the product with more than
one person. Be sure to keep your fingers and other body parts away from hot parts

2
during use (Brake, motor, chain). Never use the product with a Mp3 player, or with your
smartphone at hand.
Never use the product to pull anything, as this may damage the components and wear
out the battery. Never put the product in contact with water, the electrical components
can be damaged and create a dangerous situation. Roll only on flat and solid surfaces.
Avoid surfaces with gravel, holes, ice, which can lead to loss of control of the product.
Do not drive at night or in areas where visibility is reduced. Do not ride indoors where
there are carpets as they can interfere.
After each use, verify that each piece is in its proper place, and that it is not damaged.
Before each use, verify the following points:
-The brakes are in good condition
-All components are in good condition and in their places
-The parts with defects in the last use have been repaired or replaced according
to the manufacturer's conditions.
People who have medical follow-up or treatment such as: cardiac people, pregnant
women, irresponsible people, people with back or neck problems, should not use the
product.
When not using your scooter, usethe kickstand to keep it upright. To do this, straighten
the metal bar located under the tray of your scooter. You can adjust the height of the
handlebar using the buttons on the sleeve. Press the button and pull your handlebars
up to raise your handlebars.
•Usage of the charger
A plastic cap is located on the loading port of your scooter, remove it to load your
product, and do not forget to put it back before using your scooter so as not to damage
the loading port. Before using the product, it is necessary to charge it. A long charge
may be necessary before the first use. Please refer to the battery indicator, you can
charge your battery at any time to ensure the constant power. It is not necessary to
wait until the battery is completely empty to charge it.
Please do not use the charger of other brand, these can damage the battery of your
product. To ensure a normal life cycle, it is important to charge your battery at least
once every 3 months, even if you are not using the product. It is imperative to use the
supplied charger which is specially designed for this scooter.
Avoid shocks and contact with water, these are factors not covered by the warranty
that may damage the battery.
The supplied charger is "smart", it will stop at 100% of the charge and not damage the
battery. The charger must be in perfect condition during each use, verify the wires, the
condition of connection ends and connectors. If the product does not charge, the
charger may be defective, it needs to be replaced.
The charger must be used only by an adult, it is important to unplug it from both sides
when not charging.

3
•Battery
Please do not store the battery in extreme temperatures. Store it below 30 ° C and
above 0 ° C. If you do not use your product for 60-90 days, the battery may get worse.
This loss of autonomy is due to lack of use and is therefore not covered by the warranty.
At the end of its cycle, the battery must be discarded separately from the
undifferentiated generic waste. Discard the batteries in the containers provided for this
purpose. The recoveryand recycling of batteries contributes to protect the environment
and material resources conservation.
•Maintenance
Please store your product in a dry, dust-free place, and avoid leaving it in a humid area
or under the sun for too long. To clean your appliance, use a damp cloth and mild
detergent. Do not use alcohol, gasoline, kerosene, or other corrosive chemical solvents
to clean your appliance, which will damage its appearance and structure.
Constantly verify the condition of components of your product, if any part is damaged,
please replace it before using the product. If a part is not working, falling and injuring
may occur. Do not disassemble the scooter in case of breakdown, otherwise the
warranty will cancel. Before any intervention, it is advisable to turn off your scooter. For
all spare parts, please contact your dealer
•Transport
If you wish to transport your product by air or other means of transport as well as its
battery, please contact the local authorities and the carrier beforehand to obtain the
possible prohibitions and limits of transport. Lithium batteries are considered
dangerous in many countries. Please make sure that the access and transport are
allowed before travelling. International law prohibits the transport of lithium batteries
by air.
•Using the scooter
To turn on your product, press the Power button, then press the accelerator to
advance. To move forward, place both feet on the board, and use the right trigger on
your handlebars to advance your scooter. To brake, you can use the left trigger on
your handlebar, or press the rear fender with your foot to reduce the speed of your
scooter. Before each use, please check that the wheels are not clogged, that the
brakes are working and that no warning message is displayed. Using the scooter for
long periods can cause vibrations that can be unpleasant, make posesregularly. When

4
stopped, use the stand to stabilize your product. Unfold it with your foot. To warn other
users of your presence, use the horn located on the handlebars. Use the LED at the
front of your product to brighten your way into dark places.
•Rebus
THIS TROTTINETTE CONTAINS LITHIUM BATTERIES THAT MUST BE RECYCLED
SAFELY. Recycling: The battery must be removed before being discarded. Before any
work, remember to turn it off and unplug it from the power outlet.

5
Parts name
1
Multifunction display screen
2
The protection ring of motor cable
3
Front suspension
4
Rear suspension
5
Anti-shock wheel
Using the scooter
To move forward, place both feet on the board, and use
the right trigger on your handlebars to move your scooter
forward.
To brake, you can use the left trigger on your handlebars,
or pull the rear mudguard with your foot to reduce the
speed of your scooter.

6
Folding steps
Unfolding steps
Open the lock on the main bar of the
scooter
Press the red button.
While pressing the red button, press down
on the handlebar to retract it, then press
the lock to block the handlebars
To fold the handlebars, press the two knobs (1),
then pull the two handles (2) outwards.
Push the handlebars slightly forward then press
the button down to fold your scooter.
Press the handlebar downwards to release
it from the rear brake.
Raise the handlebars to the stop to hold the right handlebar
Raise both handles to the stop.
Adjust the handlebars size by loosening
the latch.
Raise the handlebar while pressing the red
button.
Press
Push
Push
Push
Press
Push
Press

7
Using the screen
1
Trigger of acceleration: Squeeze the trigger to advance
2
Electronic Brake Trigger: Pressing the trigger to brake, the more you press, the harder you will brake.
3
Horn: Turn on your scooter and press this button to beep.
4
Setting: There are 3 modes, "total", "trip" and "time". Press this button to change it. If you wish to reset trip mode, press
this button for 3 sec.
5
On / off button: Press this button to turn your device on or off.
6
Light: Press this button to turn on or off your light. Remember to turn it off if you do not need it.
7
Display screen
8
Speed: There are three speed modes 1/2/3, you can change speed with this button.
Advanced setting
•Two start modes:
•The first original mode allows you to accelerate directly when the scooter is stopped.
•After giving a push to the ground with your foot, the second mode accelerates when the scooter is
moving,.
To change this option, simply go to the advanced settings, press button 3 and 4 at the same time for 3sec.

8
In the menu, press "set" once, advanced option # 1 will display on the large screen. A number appears at the
bottom right of the screen, you can change it by pressing the speed button. The 0 corresponds to the first start
type, the 1 to the second start type.

9
TROUBLESHOOTING
Problem
Possible cause
Solution
It does not
work
The battery is not
charged.
Charge the battery, check if the red
light is on.
Connections or cables are
disconnected.
Check that the battery is firmly seated
in the product.
It does not
work
continuously
The battery needs to be
charged.
Charge the battery, check if the red
light is on.
The battery is not fully
charged.
Make sure the power cable is well
connected.
The battery may need to be replaced.
It suddenly
stopped
working
Overload, cut-off
Overloading may result in product
failure. Turn off the product, wait 15
seconds, then turn it on again.
Fuse burnt
Overloading can burn fuses, you may
have to replace them. For this, contact
the after-sales service.
Prior to this, check the condition of all
cables and connectors.
It is moving
slowly
The brakes are not
properly adjusted.
Check the condition of the brakes, and
try to loosen. If this does not work,
please contact the after-sales service.
It has overloaded
Check that the user weighs less than
the previously recommended weight.
Check that there are no objects
obstructing the proper operation of the
product.
Bad driving condition.
Make sure you are on flat, dry, and
constant ground.
The tires / wheels are
damaged.
Check the condition of the wheels of
the product.

10
For any information, contact our after-sales
service at the following address:
[e-mail]
You will also find many tutorial videos concerning
the maintenance and maintenance of your
product on our YouTube channel:
UrbanGlide Channel
Finally, do not hesitate to follow us on our social
networks Instagram and Facebook to follow our
news.

11
DECLARATION OF CONFORMITY
We undersigned PACT INFORMATIQUE hereby declare that the product.
Model: URBANRIDE 81 BOOST
Type: electric scooter
Function: electric scooter for individual transport
Product description: Foldable electric scooter with LED and adjustable handlebar.
Meets all standards and technical directives below:
DIRECTIVES
2014/30/EU
2006/42/EC
2014/35/EU
TESTS STANDARD
EN61000-6-1:2007
EN14619:2015
EN61000-6-3:2007+A1:2011
EN ISO 12100:2010
EN 60335-1:2012+A11:2014+A13:2017
CERTIFICATES/REPORTS
SZEM190501353901
GZES190511641201
GZES190501641201
GZHL1904016313SP
GZES190501641202
All radio emission tests were carried out by the laboratories mentioned below:
SGS-CSTC Standards Technical Services Co., Ltd.
No 1 Workshop, M-10, Middle Section, Science & Technology Park,
Shenzhen –Guangdong
China
Contact details of the manufacturer or agent:
PACT Informatique
33 rue du ballon
93160 Noisy le Grand –France
Contact details of the person authorized to edit the technical document:
Michael Barreira
33 rue du ballon
93160 Noisy le Grand –France
This declaration shall be issued under the responsibility of the manufacturer and, where appropriate,
of his representative
15/01/20 Representative of the company:
PACT INFORMATIQUE
33 rue du ballon –
Noisy le Grand - France
Maurice Bodokh
CEO

12
URBANGLIDE es una marca importada por la empresa PACT INFORMATIQUE,
ubicada en 33 rue du Ballon - 93160 Noisy Le Grand - Francia
RIDE 81 BOOST
«Traducción de las instrucciones originales»

13

14
RESUMO
SEGURIDAD Y PRECAUCIÓN
Equipo de protección 15
Consejos para el conductor 15
Procedimientos y condiciones de conducción 15
Uso del cargador 16
Batería 16
Mantenimiento 17
Transporte 17
Usando el scooter 17
Rebus 17
PRESENTACION DEL PRODUCTO Y DETALLES
Nombres de piezas 18
Instrucciones de plegado 19
Instrucciones para desplegar 19
Uso de la pantalla 20
Configuración avanzada 20

15
SEGURIDAD Y PRECAUCIÓN
Lea este manual con atención antes de usar el producto y lea sobre los riesgos y los consejos de
seguridad que aparecen en el mismo. El uso de un producto eléctrico puede ser peligroso si el
usuario no presta la suficiente atención. En caso de accidentes, la empresa no será responsable si
el producto ha sido mal usado o no se han respetado las instrucciones de seguridad. Un buen juicio
y sentido común son necesarios para que los usuarios puedan detectar posibles peligros.
Revise las normativas y leyes vigentes en su país para saber dónde y cómo usar este producto de
manera legal. Debe cumplir con las reglas y leyes que se aplican tanto a vehículos como a
peatones.
•Equipo de protección
Siempre use el siguiente equipo protector:
-Un casco aprobado y certificado dependiendo de su ubicación
-Rodilleras y coderas
-Playeras manga y pantalones largos
-Guantes
-Zapatos con suelas de goma, nunca conduzca descalzo o con sandalias Verifique que los
cordones de sus zapatos sean cortos y no se puedan enredaren las ruedas o sistema interno
del producto.
•
•Consejos para el conductor.
Este dispositivo puede ser utilizado por niños mayores de 8 años y por personas con capacidades
físicas, sensoriales o mentales reducidas o falta de experiencia o conocimiento, si se supervisa
adecuadamente, o si las instrucciones para el uso de con seguridad, les fueron entregados y los
riesgos fueron aprehendidos. Los niños menores de 8 años no deben jugar con el producto. La
limpieza y el mantenimiento del usuario no deben ser realizados por niños desatendidos.
No toque el motor o los frenos del producto inmediatamente después de su uso, estas partes
pueden estar extremadamente calientes. El peso máximo de uso es 100 kg.
Procedimientos y condiciones de conducción
Verifique que las leyes y normativas actuales de su país antes de usar el producto. Mire a su
alrededor cuando ocupe el producto, y preste atención a los riesgos posibles. Es importante
respetar los derechos y las propiedades de terceros. Para su seguridad, no acelere si no está en el
producto. Este producto no está diseñado para saltos, trucos acrobáticos y derrapes.
Nunca conduzca en la calle, cerca de vehículos, escaleras, cerros, piscinas y otros. Sostenga el
manillar con las dos manos. Nunca monte el producto con más de una persona. Asegúrese de
mantener sus dedos y otras partes de su cuerpo alejadas de las piezas calientes durante el uso del
producto (frenos, motor, cadena). Nunca use el producto con un reproductor de MP3, o con un
teléfono inteligente en las manos. Nunca use el producto para tirar objetos, esto podría dañar los
componentes del mismo y desgastar la batería. Nunca ponga el producto en contacto con el agua,
pues los componentes eléctricos podrían resultar dañados y crear una situación peligrosa.
Utilice el producto sólo sobre superficies planas y sólidas. Evite superficies de gravilla, con agujeros,
hielo, o que puedan derivar en la pérdida de control del producto. No conduzca de noche o en áreas

16
dónde la visibilidad sea reducida. No utilice el producto en interiores cuando existan alfombras que
puedan interferir en su camino.
Después de cada uso, verifique que cada pieza estén su lugar y que no existan daños. Antes de
cada uso, verifique los siguiente:
-Los frenos están en buenas condiciones
-Todos los componentes están en buenas condiciones y en sus lugares.
-Que las piezas con defectos que hayan sido reparadas o remplazadas de acuerdo a las
condiciones del fabricante,
Las personas que poseen tratamientos médicos tales como: Las personas con enfermedad
cardiaca, las embarazadas, los irresponsables, y/o aquellas que posean problemas de espalda o
cuello, no deben usar el producto.
Cuando no use su scooter, use el pie de apoyo para mantenerlo en posición vertical. Para hacer
esto, endereza la barra de metal ubicada debajo de la bandeja de tu scooter. Puedes ajustar la
altura del manillar con los botones de la funda. Presione el botón y jale el manillar hacia arriba para
elevarlo.
•Uso del cargador
Se encuentra una tapa de plástico en el puerto de carga de su scooter, retírela para cargar su
producto y no olvide volver a colocarla antes de usar su scooter para no dañar el puerto de carga.
Antes de usar el producto, es necesario cargarlo. Debe cargar el dispositivo largamente antes de
usar el dispositivo la primera vez. Revise el indicador de la batería, puede cambiarla en cualquier
momento para asegurar una potencia constante. No es necesario esperar hasta que la batería esté
completamente vacía para cargarla.
Es imprescindible utilizar el cargador suministrado que está especialmente diseñado para este
scooter. No use cargadores de otras marcas, podrían ocasionar daños al producto. Para asegurar
un ciclo de vida normal, es importante cambiar la batería al menos una vez cada 3 meses, incluso
si no está usando el producto.
Evite golpes eléctricos y el contacto con el agua que podrían dañar la batería, estos factores no
están cubiertos por la garantía. El cargador suministrado es “inteligente”, se detendrá al 100% de
carga y no dañará la batería. El cargador debe estar en perfectas condiciones durante cada uso,
verifique los cables y la condición de los conectores. Si el producto no carga, el cargador podría
estar fallando y necesitar un reemplazo.
El cargador debe ser usado por un adulto. Es importante desconectarlo de ambos extremos cuando
no esté cargando.
•Batería
No almacene la batería bajo temperaturas extremas. Guárdela en una temperatura inferior a 30°C
y superior a 0°C. Si no va a utilizar el producto durante 60-90 días, la batería podría dañarse. Esta
pérdida de autonomía es producto de la falta de uso y por lo tanto no está cubierta por la garantía.
Al final de su ciclo, la batería debe ser desechada por separado de la basura común. Deseche las
baterías en contenedores apropiados. La recuperación y reciclaje de las baterías contribuye con la
protección del medio ambiente y la conservación de los recursos materiales.