urmet domus DIGIVOICE K-Steel 1038/16 User manual

Guide to replacing the Digivoice 1038/16 Call Module
Page 5
Retrieving programming information from the existing 1038/16
Swapping the existing 1038/16
Programming the new 1038/16
Page 1
Page 4
Page 7
1038/16 voltages

Retrieving programming information from the existing 1038/16
Before replacing the 1038/16, if possible retrieve the programming information from
the existing unit as follows -
Press the Programming button on the rear of the 1038/16 call module
You will see
Use the and buttons to select then press
You will see this screen -
Make a note of the current selection and then press
At each of the subsequent screens make a note of the
current selection and press to move to the next screen
After noting the existing PASSWORD press and hold for
four seconds until you exit the programming mode
1

Door open codes
The 1038/16 call module uses two different passwords;
9998 is the default Engineer’s password and this allows access to the configuration of the
system.
9999 is the default Caretaker’s password and this only allows access to the door open codes
and the names programming.
The Caretaker’s password is automatically the Engineer’s password + 1. So if the Engineer’s
password had been changed to 1066 for example, the Caretaker’s password would
automatically be changed to 1067.
To enter either password you must first press 00. You will then see –
Enter the Caretaker’s password then press
Important note – If the 1038/16 which is to be replaced is part of a complex installation with
main and secondary call modules AND it is not possible to retrieve the existing programming
information then you must contact Urmet Technical Support.
An example of a complex installation with main and secondary call modules is as follows –
MAIN call modules.
Call all apartments
SECONDARY call modules.
Call a specific group of apartments
If the keypad of the 1038/16 is also being used to open the door, read
this section. If not then then read on from page 4
2

You will see –
Use the and buttons to select then press
You will see –
Press and hold for four seconds to exit the programming mode.
The existing code used to open the door
will appear here instead of 00000000.
Make a note of this code
3

Swapping the existing 1038/16
Before changing the 1038/16 check that the K-Steel entry panel has been correctly
installed in the first instance.
Specifically –
Make sure that the internal module guard is fitted in the top of the back box -
This guard prevents condensation from dripping into the 1038/16 and
warranty is void if it is not fitted.
If there is a gap between the wall and the back box it must be back-filled for
example with cement. If this gap is not filled then there will be no surface for
the frame holder gasket to seal against –
Mechanical installation details for K-Steel entry panels are available on request from
[email protected]
Damage caused by water ingress due to incorrect installation of the entry panel is not
covered by the manufacturer’s warranty.
Do not simply un-plug the 1038/16 and plug in the new part, re-using the existing
connectors. The cable must be re-terminated into the new connector blocks. This will
prevent any corrosion which has built up in the existing connectors from affecting the
performance of the new product.
This gap must be back filled
4

Programming the new 1038/16
When the 1038/16 is first powered the display will be in Italian.
Press 00 9998 . You will then see –
Use the and buttons to select then press
You will then see –
Use the and buttons to select then press
Use the and buttons to select then press
You will see –
Choose the TYPE and press
You will see –
Re-enter the same information into the new product
using the and buttons.
When you have finished, press and hold the
button to exit programming
A MAIN panel is one which calls ALL
apartments in a system. A SECOND
panel is one which calls only a specific
group of apartments in a system
Each panel in a system must have a
unique code.
In a system with only one panel it is not
necessary to change the default code
It was possible to retrieve the
configuration from the previous 1038/16
It was not possible to retrieve the
configuration from the previous 1038/16
5

You will see –
You will see –
You will see –
You will see –
You will see –
You will see –
You will see –
You will see –
To choose the default value press
<FREE> means that the user can open
the door without being called. <SEC>
means the user must be called before
they can open the door. <SEC> is the
normal choice. Make a selection and
press
Use the and buttons to select
<+> and use the button to increase
the time.
Use the and buttons to
select <OK> and press
Note that in some systems the lock
output triggers an access control system,
which in turn controls the lock time. In
this case set the 1038/16 lock time to 1s
To choose the default value press
To choose the default value press
To choose the default value press
To choose the default value press
To choose the default value press
6

You will see –
1038/16 voltages
Terminals Voltage
0V to + V 24V DC
0V to D 24V DC
0F to +F 33V DC
FA to FB (FA1 to FB1) Normally 0V.
After a call is made 25V DC.
After a handset is picked up approximately 13V DC
Urmet Communication & Security UK Ltd
Urban Hive, Avenue West
Skyline 120, Great Notley
Essex CM77 7AA
Tel: [phone] Fax: [phone]
www.urmet.co.uk
www.urmetmobile.com
Change as required and press
To finish programming press and hold the button until you see
7
Note – there is no need to swap any IC’s from the old 1038/16 unless there are many names in the directory.
All of the apartment numbering information is held in the 4-user decoders and not in the 1038/16
For detailed programming information see the documentation provided with the 1038/16