urmet domus 1060 Manual

DS 1060-128 LBT 20504
Mod.
1060
KIT VILLA IPERCOM
IPERCOM VILLA KIT
Sch./Ref. 1060/611
LIBRETTO INSTALLAZIONE E CONFIGURAZIONE
INSTALLATION AND CONFIGURATION MANUAL
Manuals in French,Spanish, German and Dutch can be downloaded from www.urmet.com with the QR Code shown at the end of the manual.
Les manuels en français, espagnol, allemand et hollandais peuvent être téléchargés à partir du site www.urmet.com à l’aide du code QR indiqué au fond
de la notice.
Los manuales en francés, español, alemán y holandés se pueden descargar del sitio www.urmet.com mediante el código QR presente al final del manual.
Die Handbücher in französischer, spanischer, deutscher und spanischer Sprache können mit dem am Ende des Handbuchs angegebenen QR Code von
der Website www.urmet.com
De gebruiksaanwijzingen in het Frans, Spaans, Duits en Nederlands kunnen worden gedownload op de site www.urmet.com met de QR Code aan het
einde van het boekje.
4
3
21
POE
MAX
POE Active
POE Fault
PWR
POE Ports
6
134
25
100M 10M On = Link, Blink = Act
78

26 DS1060-128
2 KIT COMPOSITION
DESCRIPTION ID
Call station Ref.1060/71
Video door unit with 1 button
A
1 transparent printed tag
1 grey printed tag
1 red printed tag
Flush-mounting box Ref. 1145/52 1 flush mounting box 2 modules A1
Frame and module holde Ref. 1158/62 1 frame and holder for 2 modules A2
Max Monitor Ref. 1717/31
Max apartment station video door phone with fastening bracket
B
Package containing 6 screws, 4 anchor bolts for fastening bracket and sticker for
hearing impaired
Terminal board with connectors
PANI C
FC
S+
S-
+B
-B+V-V
+-
8-port switch Ref. 1039/44 1 switch with 8 ports, of which 4 PoE. C

27
DS1060-128
3 ACCESSORY DEVICES
DESCRIPTION ID
Supplementary call station Ref. 1060/71 -
Electric lock 12 Vac 15 VA - OP1
Flush-mounting box Ref. 1145/52 -
Frame and module holder Ref. 1158/62 -
Setup for activating garage gate door opener - OP2
Button for activating pedestrian gate electric lock - OP3
Hood for two-module door unit Ref. 1158/612 OP09
Supplementary Max Monitor Ref. 1717/31 OP4
Supplementary ringer Ref. 1072/59 OP5
Floor call button - OP6
Ipercom actuator relay Ref. 1060/84 OP7
Generic ADSL router - OP8
Supplementary PoE Switch Ref. 1039/44 -
720P H264 IR PIE Minicamera and Audio (Urmet Cloud series)
Compact camera IP H.265 4M AF 2.8 – 12mm
DOME indoor IP H.265 4M AF 2.8 – 12mm
VANDAL DOME IP lens IP H.265 4M AF 2.8 – 12mm
Ref. 1093/184M18
Ref. 1093/144M4ZI
Ref. 1093/181M4ZI
Ref. 1093/182M4ZI
OP9
(#)
(#) For the updated list of the Urmet cameras available, contact the Client Service Technical Area.

28 DS1060-128
4 CONNECTION BLOCK CHARTS
4.1 SINGLE-FAMILY SYSTEM
Apartment 01
4
3
2
1
POE
MAX
POE Active
POE Fault
PWR
POE Ports
6
134
25
100M 10M On = Link, Blink = Act
78
LAN
NC
OUT 1
C
REL. FW:
PB1
PB2 V-
V+
DECODIFICA SPECIALE PER CAT 5
SPECIAL DECODER FOR CAT5
NO NO
OUT 2
C
NC
Light 02Light 01
PoE
PoE
PoE
PoE
A
B
C
OP4
OP6
OP5
110-230 Vac
110-230 Vac
2
2
2
2
2
OP6
OP5 OP8
2
2
OP3
OP2
OP1
OP7
110-230 Vac
110-230 Vac
OP9
Internet
4.2 DISTANCES
For connections between various IP devices, the maximum distance allowed is 100m, the distance established by standard IEEE802.3 for Fast Ethernet
networks (100Mbps).
To guarantee correct functioning of the monitor at maximum distances, the cable must be category 5e and the gauge of the pairs must be
AWG24. The maximum resistance of the individual wire must not exceed 10ohm/100m.
The wire must comply with the following standards:
- EIA/TIA 568-B.2
- EN50288 3-1
- IEC 61156-5
The connection between the monitor and the PoE switch must be made with a single wire without using additional patch cords.
For the other connections (that do not involve the IP devices), refer to the table below:
Segment
Type of wire
Wire 1mm2single
A – OP1 60 m
A – OP2 60 m
A – OP3 100 m
B – OP5 30 m
B – OP6 30 m
B – local power 25 m

29
DS1060-128
5 WARNINGS FOR INSTALLERS
Read the notes in this manual carefully. This manual contains important information on safe installation, use and maintenance.
This devices in the kit must only be put to the use for which they were intended. All other use is improper. The manufacturer cannot be held responsible
for damage deriving from improper, incorrect or unreasonable use.
Each part was designed to be compliant with the standards in force.
The system must be built in compliance with the regulations in force. All devices in the system must be exclusively used for the purpose for which they
were designed.
Remove the components from the packaging and check that they are intact.
Keep the packaging (plastic bags, polystyrene, etc.) away from children. Packaging is potentially dangerous.
Provide a suitable cut-off and protection master switch upstream from the devices, with contacts open by at least 3 mm.
Make sure that the plate data corresponds to the power specifications before connecting the devices to the mains.
Keep the ventilation or cooling openings and slots free.
Disconnect the devices from the mains before cleaning or maintenance.
Do not use spray products to clean the device.
Disconnect power from the circuit breaker in the event of failure and/or malfunctioning of the products contained in the kit. Do not tamper with the
devices.
Exclusively contact a service centre authorised by the manufacturer for repairs.
Provide suitable ventilation.
Do not use power extension wires.
Have the device checked and repaired by qualified personnel in the case of infiltration of fluid or objects inside the device.
Exclusively use the spare parts supplied by the manufacturer for repairs.
Installers must make sure that user’s information is applied to the connected devices.
Disrespect of these precautions can effect safety of the devices.
Keep this manual with the device at all times.
The lightening symbol in a equilateral triangle indicates the presence of dangerous voltage.
Never open the devices unless expressly instructed to do so in this instruction manual.
The exclamation mark symbol in an equilateral triangle indicates critical safety components. Always only use components supplied by the
manufacturer.
6 CONFIGURATION OF SYSTEM START-UP
6.1 PRELIMINARY OPERATIONS
The system is configured by following a procedure consisting of a few system steps, after which the system can perform the main video door phone
operations.
When the system is turned on, the Max Monitor displays this screen:
Figure 1: MAX monitor home page
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•

30 DS1060-128
6.2 SELECTING LANGUAGES
The first operation to be carried out in the home page is to select the system language by pressing the LANGUAGE button.
Select the desired language in the window that opens.
Figure 2: Selecting the system language
If Italian is selected, the home page will be translated immediately as expected.
Figure 3: Home page translated into Italian
6.3 ACCESSING THE CONFIGURATION MODE AND SETTING THE DATE AND TIME
To access the configuration mode, touch the CONFIGURATION button on the home page: a screen will appear where the Urmet password must be
entered
Figure 4: Entering the Urmet password
The Urmet default password is “1937”.

31
DS1060-128
Entering the password and pressing the CONFIRM button allows access to the configuration mode.
The first page that appears is the one for selecting the current date and time, a fundamental step for correctly configuring the system.
Figure 5: Setting the date and time
By entering data into the year, month, day, hour, and minute columns and then pressing the CONFIRM button, the system acquires the correct date and
time.
At this point, the configuration menu will appear, where it is possible to create the first system configuration.
Figure 6: Configuration Menu
6.4 CREATING THE CONFIGURATION
To create the first system configuration, select the item “System Configuration” from the menu and then “Create configuration”, as show in the figure
below.
Figure 7: Step-by-step creation

32 DS1060-128
The following page will appear
Figure 8: Creating a new configuration
6.4.1 SETTING THE BASE PARAMETERS
On the create configuration page, select the type of Villa Kit project (single family) and then assign a meaningful name to the project and an installer’s
password.
Figure 9: New configuration setting
To allow future modifications of the configuration created, it is recommended that the installer password be noted and saved in a safe place.
Once the OK button is pressed, an empty configuration will be created and a page will appear where it is possible to add the individual devices to the
configuration and configure them.
Figure 10: Basic configuration
The section highlighted to the left is the NAVIGATION MODULE and makes it possible to add devices by positioning the cursor on the apartment or in the
floor desired.

33
DS1060-128
6.4.2 SETTING THE MAX MONITORS
Ensure that the apartment is selected in the navigation module, or that the App 01 button is pressed as shown in the figure.
Figure 11: Selecting the apartment from the navigation module
To add the MAX monitor to the apartment, first press the Add new device button: the following page will appear
Figure 12: Selecting the device to be added to the apartment
Then select the item Max 1717/31-32-33-34-41 to open the MAX monitor settings page
Figure 13: Setting the MAX monitor

34 DS1060-128
Assign a name to the device using the Name field, then press the button in correspondence or the MAC Address: a new window will appear, as
illustrated in the figure below
Figure 14: Selecting the MAC address
By pressing the This Device button, the MAC Address field will be filled in automatically and the device setting will be completed
Figure 15: Completing the MAX Monitor Settings
Press OK to confirm the parameters entered: the device will be added to the apartment, as illustrated in the figure below
Figure 16: MAX Monitor added to the apartment