urmet domus 1083/12 User manual

Configuration guide
System Type A
1083/12 -1083/15 -1083/16

Contents
Introduction
Menu structure
Configuration
Programming proximity access keys
Programming door open codes
Appendix
Contents
Introduction
Menu structure
Configuration
Programming proximity access keys
Programming door open codes
Appendix
Contents
Introduction
Menu structure
Configuration
procedure
Programming proximity access keys
Programming door open codes
Appendix
procedure
Programming proximity access keys
Programming door open codes
procedure
Programming proximity access keys
Programming door open codes
Programming proximity access keys
Page 1
Page
Page 4
Page 12
Page 1
Page
Page 1
Page
3
Page 4
Page 12
Page 1
3
Page
14

Introduction
1083/201083/20 1083/75
System Type A–
One (or up to a maximum of four) ‘Main’ entry panels
i.e. panels which call all apartments in the system.
The apartment numbers are in the range of 1 to 127.
Example 1 -A block of fifty apartments with postal
addresses from 1 to 50
Example 2 -A block of twenty apartments with postal
addresses from 101 to 120.
This programming guide is intended specifically for a particular type of system –System Type A
Page 1

53
53
53
In
System Type A
on the entry panel, the system will ring the
monitor with the DIP switch setting
In other words the binary address on the monitor
or monitor bracket should be set to the same
number as the apartment postal address.
Page 2
System Type A
on the entry panel, the system will ring the
monitor with the DIP switch setting
In other words the binary address on the monitor
or monitor bracket should be set to the same
number as the apartment postal address.
Page 2
USER 53
System Type A
on the entry panel, the system will ring the
monitor with the DIP switch setting
In other words the binary address on the monitor
or monitor bracket should be set to the same
number as the apartment postal address.
USER 53
when you dial for example
on the entry panel, the system will ring the
monitor with the DIP switch setting
In other words the binary address on the monitor
or monitor bracket should be set to the same
number as the apartment postal address.
USER 53
when you dial for example
on the entry panel, the system will ring the
monitor with the DIP switch setting
In other words the binary address on the monitor
or monitor bracket should be set to the same
number as the apartment postal address.
when you dial for example
on the entry panel, the system will ring the
monitor with the DIP switch setting
53
In other words the binary address on the monitor
or monitor bracket should be set to the same
number as the apartment postal address.
when you dial for example
on the entry panel, the system will ring the
53
.
In other words the binary address on the monitor
or monitor bracket should be set to the same
number as the apartment postal address.
when you dial for example
53
In other words the binary address on the monitor
or monitor bracket should be set to the same

Menu Structure
LANGUAGE
CONFIGURATION
NAMES
DOOR OPENER
KEYS
RESET
SIMPLIFIED GUI
MODULE TYPE
MULTIRISE
ID PRIMARY MODULE
CODE TYPE
BUSY TIME
STOPABLE
DOOR LOCK 1 RELEASE TIME
DOOR LOCK 1
DOOR LOCK 2 RELEASE TIME
DOOR LOCK 2
PASSWORD
LCD BACKLIGHT
BUTTON SOUND
MULTITOUCH CALL
WELCOME MESSAGE
TIME ZONE
DATE AND TIME
DAY
POSTMAN
VOCAL SYNTHESIS
SWITCHBOARD
NEW
MODIFY
DELETE
DELETE ALL
NEW
MODIFY
DELETE
DELETE ALL
NEW
MODIFY
DELETE
Page 3
Note –It is necessary to pass
through each configuration step
and arrive back at the top level
menu for information to be saved

Configuration procedure
When the unit is first powered the screen is as follows –
On the entry panel keypad press 99999 and you will see this screen –
Enter 1000 (the default password)then press
Use the and buttons to select
LINGUA and press
Use the and buttons to select
ENGLISH UK and press
ENGLISH UK
Page 4

You see this screen –
Press the button to select CONFIGURATION then press
Use the or buttons to select NO and press
NO
YES
PRIMARY
SECONDARY
Use the or buttons to select PRIMARY and press
Use the or buttons to select NO and press
YES
NO
Page 5
CONFIGURATION

LANGUAGE

PHYSICAL
In a system with only one entry panel the ID is always 0. In this case just press .
In a system with two, three or four panels, each must have a different ID.
For example to change the panel ID to 1just press then press
Use the or buttons to select PHYSICAL and press
LOGICAL
It is suggested to keep the default setting by pressing
It is suggested to keep the default setting by pressing
Page 6
The ID of the panel is determined by where it is connected in the system.
You must refer to the connection diagram of your system for the ID of each panel.

DOOR LOCK 1 RELEASE TIME adjusts the voltage free relay (C NO NC) time
and also the solid state lock release output (SE+ SE-) time.
For example for a time of 10 seconds press 1 0
Choosing FREE means that the door can be opened by the monitor or handset at
any time without the monitor or handset being called.
Choosing SECRET means that the monitor or handset must be called before it can
open the door.
Use the or buttons to make a selection then press
DOOR LOCK 2 RELEASE TIME adjusts the voltage free relay (C NO) time.
For example for a time of 1 second press 1then press
Choosing FREE means that the gate can be opened by the monitor or handset at
any time without the monitor or handset being called.
Choosing SECRET means that the monitor or handset must be called before it can
open the gate.
Use the or buttons to make a selection then press
For an explanation of the three different lock outputs see the appendix
Page 1
4
Page 7

Change the PASSWORD if required by pressing the button below Cto delete
the current password -
Enter the new password and press
Adjusts the panel display backlight
Use the or buttons to make a selection then press
The entry panel button confirmation beep can be ON or OFF.
Use the or buttons to make a selection then press
Page 8
It is possible that when a number of buttons are pressed at the same time, a
particular monitor or handset can be called, for example a caretaker’s apartment.
If you wish to use this feature enter the apartment address then press .
Otherwise just press