Vaisala SPH10 Product manual

© Vaisala 2012. All rights reserved. *M211542EN*
INSTALLATION AND
MAINTENANCE GUIDE
Static Pressure Head
SPH10
– Eliminates effectively w i nd
disturbances
from pressure
measur e ment s
– Adaptable to many
barometers,
directly to Vaisala PTB 210
– Durable and easy to
clean
INTRODUCTION
Vaisala model SPH10 Pressure Head provides an effective
elimination of pressure variations in the barometer due to the
wind. The SPH10 is easy to clean and maintain. It can be
integrated directly with the Vaisala PTB210 barometer. To other
barometers the SPH10 can be connected with pressure tubing.
ASSEMBLING
1. Screw the lower bar to the threaded sleeve of the lower
plates (with 6 holes).
2. Screw the upper bar (with mounting plate) to the threaded
sleeve of the upper plates.
MOUNTING
Select an open location, prefereably a place higher than the
surroundings, with no buildings or trees nearby. Attach the
SPH10 to a horizontal pole using a mounting plate. A suitable
pole is Vaisala sensor mast, type DKP12. However, any other
horizontal pole with two screws (M6) in a distance of 41 mm can
be used.
NOTE The recommended distance of the SPH10
from the vertical pole is at least 1.5 m.
1. Loosen the two fixing screws of the pole and fix the SPH10
into the pole as indicated in Figure 1.
2. Attach the SPH10 by tightening the screws. (The pressure
Head is removed by loosening the two screws).
CONNECTION TO THE VAISALA PTB210
Visualization in Figure 2.
1. Detach the threaded nipple and the gasket (see figure 1).
2. Place the O-ring into the barometer groove.
3. Attach the PTB210 to the SPH10 with two fixing screws.
CONNECTION TO OTHER BAROMETERS
Connect the barometer to the threaded nipple (Figure 1) by using
a flexible, airtight tube with an inner diameter of 4 mm. To
prevent condence water accumulation in the tube, make sure the
entire length of the tube goes downwards from the barometer to
SPH10.
Figure 1 SPH10 Static Pressure Head
Figure 2 PTB210 Barometer Connection
Shanghai R.P.China
NO.32,ShuPing Road,JiadingDistrict,ZIP201802,
上海博众测量技术有限公司
Bodhi (Shanghai) measurement technology Co.,Ltd.
TEL: [phone]/62/63
FAX: [phone]
NO.32,ShuPing Road,JiadingDistrict,ZIP201808,

Visit our Internet pages at Ref. M211542EN-A
TECHNICAL DATA
Property Description / Value
Materials
Plates Polycarbonate
Bars Offshore Aluminium
Mounting with 2 bolts
(M6 x minimum 20 mm)
Weight 800 g
Hose connection barbed fitting for 4 mm I.D.
hose or Rp1/4 thread
(parallel)
MAINTENANCE
Figure 3 Detaching the Lower Plate for Cleaning
Cleaning the SPH10 is done by detaching the lower bar and the
lower plate. The barometer can be in place while cleaning the
plates. Follow the instructions below:
1. Unscrew the lower bar and detach it.
2. Open the self-locking nut with a 13 mm spanner.
3. Remove the threaded sleeve and take out the lower plate
and the protective wire net.
4. Clean the plates.
5. Replace the lower plate, the protective wire net and the
threaded sleeve, screw back the nut and the lower bar.
Keep the holes of the lower plate open to allow the water run
out.
DIMENSIONS
All dimensions in mm.
Shanghai R.P.China
NO.32,ShuPing Road,JiadingDistrict,ZIP201802,
上海博众测量技术有限公司
Bodhi (Shanghai) measurement technology Co.,Ltd.
TEL: [phone]/62/63
FAX: [phone]
NO.32,ShuPing Road,JiadingDistrict,ZIP201808,