Velleman HAA51 User manual

MODEL HAA51
PASSIVE INFRARED
INTRUSION DETECTOR
PASSIVE INFRAROOD
DETECTOR
DETECTEUR D’INTRUSION
PASSIF INFRAROUGE

OPERATING MANUAL HAA51
PASSIVE INFRARED INTRUDER DETECTOR
INTRODUCTION
HAA51 Passive Infrared Intruder Detector is designed for indoor use in advanced residential
and commercial security systems. It detects the movement caused by a human target moving
across the detection field. The detector employs many features that are only available in the
most advanced intrusion detectors.
HAA51 is designed with the most up-to-date electronic circuitry for high performance and
reliability. It employs a dual-element, pyroelectric sensor incorporating a "daylight" filter
designed to provide immunity from common-mode signals such as the effect of strong hot or
cold air currents, variations in ambient temperature, background radiation and acoustic noise.
The dual-element sensor provides substantial immunity to false alarms. The HAA51 also
employs a pulse-count triggering circuit which provides further improvement in this respect.
HAA51 can also be selected for single-shot triggering.
HAA51 is designed to be surface mounted or corner mounted on a wall at the height of 2m
above the floor. It provides the illustrated protection pattern without calibration or adjustment.
THE CASE ASSEMBLY THE PRINTED CIRCUIT BOARD
DESCRIPTION
* Fresnel Lens an optical system for focusing the infrared radiation on the
heat sensitive elements of the sensor.
* Alarm/Walk Test Indicator It lights up for approximately 2 seconds whenever movement
is detected.
* Knock-Outs Entry holes for running connection wires in and out.
* Mounting holes Prepared for fixing the unit to the wall.
* PCB Support Post For supporting and fixing the printed circuit board firmly in
the case.
* Locator For convenient observation of the detection zones.
* Sensor The infrared signal detection device. DO NOT TOUCH.

* LED Function Mode Selector -
This selector consists of a 4-pin connector and a jumper which can be inserted between 2
pins, enabling 3 operational modes:
a. OFF - Link pins 1 and 2 with jumper. -
This mode can be used to disable the ALARM/WALK test LED and LOCATOR LED
after all testing is completed in order to prevent unauthorised persons from tracing the
protection area.
b. ZONE - Link pins 2 and 3 with jumper. -
This mode is used for locating the beam. The locator LED lights continuously to enable
convenient observation of the detection zones.
c. ALARM - Link pins 3 and 4 with jumper. -
This mode is used for ALARM/WALK testing. The ALARM/WALK indicator lights up
whenever movement is detected.
NOTE: Factory setting in for the ALARM mode.
* Triggering Mode Selector
The detector can be selected for single-shot triggering or pulse-count triggering. This
selector consists of a 3-pin connector and a jumper which can be inserted between 2 pins,
enabling the 2 operational modes:
a. Single Shot - Link pins 1 and 2 with jumper. -
Single-shot trigger mode makes the detector go immediately into the alarm condition
whenever an intruder moves in or out of the detection zone. The detection circuit
requires 1 pulse to activate it. It is recommended to use single-shot operation for narrow
corridor protection.
b. Pulse Count - Link pins 2 and 3 with jumper.
Pulse-count trigger mode further improves immunity against false alarms. The circuit
first senses an alarm (pulse 1) and then goes into alarm stand-by mode for 30 seconds. If
during the 30 second stand-by period a second alarm event occurs (pulse 2), the detector
immediately goes into alarm mode and the stand-by period will be extended for another
30 seconds. If there is no second alarm pulse during the 30 second stand-by mode, the
detector returns to normal condition.
NOTE: Factory setting for pulse-count operation.
* Tamper Switch Protects the unit from tampering. The contact of the switch is
normally closed when the cover is closed; and is connected to
the "TAMPER" terminals of the terminal block.
* Reed Relay This is a silent relay with its contact connected to the
"ALARM" terminals. The contact is normally closed (fail
safe) and will open when an intruder is detected or during
power loss.
* Terminal Block For connecting wires to the sensor.

WIRING
TAMPER Connect the "TAMPER" terminals
to a normally closed 24-hour
protection area of the control
panel. The tamper contact will
open when the cover is removed.
12V DC Connect the 12V DC terminals to a power source of 8-16VDC,
making sure that they are connected with the correct polarity.
ALARM Connect the "ALARM" terminals to a normally closed burglar
protection zone of the control panel. The contact will open when an
intruder is detected or during power loss.
TEST POINT (T.P.) The T.P. is an auxiliary terminal which provides a useful means for
the technician to analyse the detector in the event of an environment
problem or a suspected faulty detector. Connect a DC voltmeter (with
minimum input impedance of 20KOhm/V) with its positive lead to the
T.P. terminal and the negative lead to the (-) 12V DC terminal as
shown in the following diagram.
The meter should read approximately 2.7V DC when no movement is detected. Any
movement into or out of the detection zone will cause the meter to deflect above or below the
2.7 volt level. Any meter variation of +/- 1V will be considered as one pulse which will
trigger an alarm output when the detector is in single-shot operation. If pulse-count operation
is selected, the detector will require a second pulse within 30 seconds after of the end of the
first pulse for the alarm to be triggered.
Using this feature during installation, the alarm contactor can learn of potential false-alarm
problems before permanent fitting of the detector.

SELECTING MOUNTING LOCATION
The detector can be surface mounted or corner mounted. Always mount the unit on a sturdy
surface.
* The detector should be mounted indoors, in areas that do not have openings constantly
exposed to the outside environment.
* Select the mounting location so that the expected movement of an intruder will cross the
detection beams.
* Do not locate detectors where hot or cold moving air will blow directly onto the unit.
* Avoid aiming the detector at heating or air
conditioning vents or ducts, exterior metal
walls, exterior windows or curtains covering
windows, refrigerator or freezer grills or any
other surface that may change temperature
rapidly.
* Avoid putting large objects in front of the
detector which will cause significant changes
in the area or volume protected.
* Select a location that the detector can
provide the largest coverage.
The installation location in figure A gives a larger protection area.
Figure A Figure B
VERTICAL
HORIZONTAL

INSTALLATION
a. Open the cover by inserting a small
screw driver into the edge of the unit
and turn clockwise or anti-clockwise
slightly to release the cover from the
back plate.
b. Remove the Printed Circuit Board
carefully by releasing the two fixing
screws from the PCB support post.
CAUTION: DO NOT DROP OR
DAMAGE THE PCB ASSEMBLY.
c. Numerous "knockouts" are provided on
the back plate. Select the one which will
provide the best location for feeding
cables through.
d. Select a location 2 m above the floor for mounting the back plate.
e. The two fixing holes on the back of the back plate are for surface mounting. The two fixing
holes on the left and right of the back plate are for corner mounting.
Fix the back plate firmly on the wall by using the two screws supplied.
f. Put the PCB back into the back plate and fix it firmly.
g. Connect the wires to the terminal block.
h. Clip the front cover back in place on the back plate.
CAUTION: BE SURE TO FIT THE ALARM/WALK TEST LED INDICATOR INTO THE
INDICATOR HOLE AND KEEP THE HINGED LEVER OF THE TAMPER MICRO-
SWITCH PRESSED WHEN CLIPPING THE FRONT COVER.
TESTING
a. Set the LED selector to "ALARM" for testing purposes and replace the cover.
b. Apply 12V DC power and allow 3-5 minutes for the detector to warm up and stabilise
before testing.
c. Walk into the protected area at a speed of 1 step per second, across the protection beams,
and watch the LED. The LED will light up whenever you enter or exit a protection beam if
the detector is set to single-shot operation.
You may need to take 3 to 4 steps for the first alarm trigger and for the LED to light up if
the detector is set to pulse-count operation.
The detector converts to single-shot operation (stand-by mode) for 30 seconds after the first
trigger. The LED will light up whenever you enter or exit a protection beam area. The
single-shot operation will be extended for 30 seconds after each trigger, but if there is no
trigger during this 30 second period, the detector will return to normal pulse-count
operation.
d. If proper detection does not occur during the walk tests, relocating or re-aiming the detector
may be required.

TROUBLESHOOTING
I. Alarm/Walk test LED does not light when unit is walk-tested:
a. No power to detector
- Check cable, connection and power source.
b.LED selector not set to "ALARM"
- Check jumper position.
c. Not walking into detection pattern
- Check location of zones using pattern locator and re-test.
d. Background temperature equal or close to body temperature
- Reduced range can be expected when background and body temperature come close
or are equal to each other.
e. Defective unit
- Replace the circuit board.
II. Alarm/Walk test LED lit continuously:
a. The detector is seeing changing levels of infrared energy
- Clear area of all people and pets.
- If LED remains lit, cover detector with heavy paper and wait 1 to 2 minutes.
If LED extinguishes, check each detection zone to locate source of energy.
b. Defective unit
- If LED remains lit after detector has been covered with heavy paper, replace circuit
board.
III. Detector randomly alarms:
a. Power source being interrupted
- Check wiring and connection.
b. Cover not properly secured or excessive mounting surface vibration
- Make sure that the cover is firmly in position and that the detector is free from
vibrations.
c. The detector is seeing changing levels of infrared energy
- Switch all known sources, such as heaters, lights, air conditioning vents, etc.
See precautions listed in the section "Selecting mounting location".

SPECIFICATIONS
Detection pattern: 84.2º beam, 12m range.
Detection zones: 24 dual-element zones in 3 layers.
LED indicators: One pattern locator, one Walk/Alarm test indicator. (3-mode operation
selectable, factory preset to ALARM/WALK position)
Mounting height: 2m above floor, 13.96º angle of tilt on back-plate, no height
adjustment required in installation.
Mounting location: Indoors only; flat surface or corner mounting.
Operating voltage: 10.5-16V DC.
Quiescent current: 12mA typical.
Sensor: Dual-element pyroelectric sensor with day-light filter.
Triggering mode: Pulse-count or single-shot selectable. (Factory preset for pulse count)
Alarm output: Normally closed (fail safe) contacts, 0.5A/24V rating.
Alarm delay: 2 seconds typical.
Tamper contact: Normally closed when depressed, 0.5A/24V rating.
Test output: Test point analysis.
SPECIFICATIONS ARE SUBJECT TO MODIFICATIONS WITHOUT NOTICE