Velleman HAM263D User manual

HAM263D
HOME ALARM STARTER SET
ALARM STARTPAKKET
KIT SYSTÈME D’ALARME DE BASE
JUEGO CON SISTEMA DE ALARMA BÁSICO
ALARM STARTERPAKET
USER MANUAL 3
GEBRUIKERSHANDLEIDING 20
NOTICE D’EMPLOI 37
MANUAL DEL USUARIO 54
BEDIENUNGSANLEITUNG 71

HAM263D
00 (10/10/2008) VELLEMAN
3
User manual
1.1 Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its
lifecycle could harm the environment. Do not dispose of the unit (or batteries) as
unsorted municipal waste; it should be taken to a specialized company for recycling. This
device should be returned to your distributor or to a local recycling service. Respect the
local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing Velleman! Please read the manual thoroughly before bringing this device into
service. If the device was damaged in transit, do not install or use it and contact your dealer. Damage
caused by disregard of certain guidelines in this manual is not covered by the warranty and the
dealer will not accept responsibility for any ensuing defects or problems.
The HAM263D is an all-in alarm system kit designed for home and office protection. The HAM263D
is controlled via a digital keyboard. It can be configured in different partitions that work
independently or in combined operation.
1.2 Safety Instructions
Keep the device away from children and unauthorised
users.
Indoor use only.
Keep this device away from rain, moisture, splashing and
dripping liquids.
Remove power before opening the cover. Be very
careful, touching live wires can cause life-threatening
electroshocks.
•Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and
the dealer will not accept responsibility for any ensuing defects or problems.
•Keep the device away from splashing and dripping liquids.
•Note that damage caused by user modifications to the device is not covered by the warranty.
1.3 General Guidelines
•Protect this device from shocks and abuse. Avoid brute force when operating the device.
•Protected the device against extreme, dust and moisture.
•Familiarise yourself with the functions of the device before actually using it.
•All modifications of the device are forbidden for safety reasons.
•Only use the device for its intended purpose. Using the device in an unauthorised way will void the
warranty.
1.4 Features
•arm/disarm status control via digital keypad
•8 coverage zones divided in two sections
•programmable exit delay, entry delay 1 & 2 and alarm duration time
•independently programmable user codes for section 1, section 2 and the entire system
•user codes of 4 to 6 digits
•response time of each protection zone is independently programmable
•power low watchdog resets the system before battery is exhausted
•non-volatile memory
•entry and exit warning beeps on/off
•arm/disarm ring back indication on/off
•instant arming code, both for home and away operation
•connection of siren, bell, satellite siren and strobe light possible

HAM263D
00 (10/10/2008) VELLEMAN
4
•built-in dynamic battery charger with automatic or manual battery testing
•on-board software section for panic alarms
•possibility to bypass faulty zone(s) to arm the system
•handover option for the instant zones
•connect up to 4 control keypads HAA236D or key switches HAA80MK
•tamper-proof
Kit includes 1 x master control unit
1 x weatherproof alarm control keypad (HAA263D)
2 x PIR intrusion detector (HAA52N)
1 x electronic siren
1 x panic button (HAA60)
5 x magnetic contacts
1 x 16,5VAC/3A power adapter
Optional HAA263D auxiliary weatherproof control keypad for alarm control panel
HAA52N PIR intrusion detector (max. 6, depending on power consumption)
HAA60 panic emergency button
HAA25 magnetic reed switches
HAA27 magnetic reed switches
Optional – arm/disarm control only
HAA80MK remote control panel switch with momentary key
HAA85WP multi-purpose security keypad - water-resistant
2. Master control unit
2.1 General
The master control unit is the heart of the alarm system. The cabinet contains a baseboard
containing a series of jumpers to set-up the system and a connection block with 28 contacts where
all connections are made to the input devices such as PIR motion sensors, keypad(s), magnetic
contacts etc. …, output devices such as siren(s), strobe lights etc. …
The device should only be installed and serviced by a qualified person.
Connection block

HAM263D
00 (10/10/2008) VELLEMAN
5
1
2 AC in AC Power input from a 16.5VAC, minimum 1.5A, 50~60Hz transformer. The primary side of the transformer must be connected to an un-switched receptacle.
The used transformer must comply with the EN61558 standard for European
countries.
3 DC out Un-switched +12VDC output power referring to the common ground. Continues
output, not depending on the arm/disarmed status. Can be used for devices requiring
uninterrupted power supply e.g. smoke detectors, control keypads etc. This output
has a 750mA resettable fuse.
4 GND Common Ground (-)
5 DC out Continuous +12VDC output power under normal condition (no alarm). The output is
switched OFF at alarm condition; it has a 2.5A resettable fuse. Suitable for the
connection of satellite siren/strobe light with internal battery.
6 DC out Continuous +12V output power under alarm condition until the system is disarmed.
The output has a 2.5A resettable fuse. It is mostly suitable for providing power for the
stand alone strobe light or those devices require continuous operation at alarm
condition after the siren timer is reset (e.g. SV/PSL3).
7 DC out +12V output power under alarm condition with the duration depending on the
setting of the alarm timer; it has a 2.5A resettable fuse. Can be used for electronic
siren or alarm bell.
•The following 4 contacts are dedicated for the connection of one or more digital keypads, e.g.
HAA263D, HAA85WP… The total number of keypad(s) and key switches however is limited to four.
8 GND Common Ground (-) for keypad(s)
9 CLK Clock wire for keypad(s)
10
Data Data wire for keypad(s)
11
DC out +12V output power common point with a 750mA resettable fuse for keypad(s) and
key switches.
•The following 5 contacts are for inputs from key switches, e.g. HAA80MK.
12
Part 1 ON/OFF Arm/disarm partition 1: accepts normally open (N.O) momentary switches.
Multiple switches can be connected in parallel.
13
Part 2 ON/OFF Arm/disarm partition 1: accepts normally open (N.O) momentary switches.
Multiple switches can be connected in parallel.
14
Part 1 status LED indication partition 1: show zone status of partition 1.
15
Part 2 status LED indication partition 2: show zone status of partition 2.
16
System status LED indication system: show zone status of entire system.
Note that contacts 12 and 13 can be connected together to one key switch to arm or disarm
partition one and two simultaneously.
•The following 12 contacts are for the connection of sensor inputs e.g. PIR detectors (HAA52N),
magnetic contacts (HAA25, HAA27) panic buttons (HAA60) … They represent zone 1 to 8 and their
common groundings. The zones are End of Line (E.O.L.) monitored by a 2.2Kresistor.
•All normally closed (N.C.) contacts are to be wired in series with the E.O.L. resistor, where all
normally open (N.O.) contacts are to be wired in parallel with the E.O.L. resistor.
1. N.C. contact
2. N.O. contact
3. 2.2KE.O.L. resistor

HAM263D
00 (10/10/2008) VELLEMAN
6
17
Zone 1 Delay Partition 1
18
GND Common ground for zone 1 and zone 2
19
Zone 2 Instant Partition 1
20
Zone 3 Instant Partition 1
21
GND Common ground for zone 3 and zone 4
22
Zone 4 Delay Partition 2
23
Zone 5 Instant Partition 2
24
GND Common ground for zone 3 and zone 4
25
Zone 6 Instant Partition 2
26
Zone 7 Delay Common, for common area e.g. lobby. Disarmed when either one of the
partitions is disarmed, only armed when both partition 1 and 2 are armed.
27
GND Common ground for zone 7 and zone 8
28
Zone 8 Instant Common, 24 hour instant alarm. Cannot be switched off, except in standby
mode.
Programming jumpers
System setting: Key Switch (KS) or Digital Keypad (DK).
KS: for systems with only key switch arm/disarm control (not applicable for
HAM263D)
DK: for systems with digital keypad and combined keypad/key switch control.
This jumper sets the time for the entry delay. This is the time between arming the
partition/zone and the beginning of detection in that zone. Entry delay is used in
zones 1, 4 and 7 and can be set to 15, 30, 60 or 90 seconds.
This setting determines the duration of the output signal on contact 7, and thus the
duration of the activation of connected devices e.g. siren, bell …. Possible options are
3, 5 or 15 minutes, or indefinite (until manual reset).
It is strongly advised not to use the indefinite option when using sirens or bells. Many
local authorities do not allow it.
These 3 jumpers control the entry, exit and warning beeps.
The entry beep sounds during the entry delay period
The exit beep sounds during the exit delay period
The warning beep depends on the status of the system:
a. Only one partition armed. Warning beep sounds during alarm and resets after
alarm expiration time.
b. Both partitions armed. Warning beep sounds during alarm and continues until
one of the partitions is disarmed.
With the handover function enabled, when zone 7 is triggered first, the instant zones
(except for the 24 hour instant zone) will set the same entry delay period as zone 7.
The instant zones will resume to instant mode after the entry delay time expires.
When another instant zone is triggered first, the alarm will sound instantly. This setup
allows that entry via one entrance (e.g. main door) delays the whole alarm system,
while attempts to enter via a different way will immediately trigger the alarm.
When set in the ON position, the ring-back function enables contact 7 twice for a short
while when the system is armed or ones when the system is disarmed. This produces
a sound signal through the connected siren or bell.

HAM263D
00 (10/10/2008) VELLEMAN
7
Audible notifications
During operation, following audible signals will be generated by the master control unit.
Event Notification
System in Exit Delay Period
OR
System in Entry Delay Period
Exit And Entry Beeps
•Short beeps at 0.5 second interval
•Increase to 4 beeps/second at the last 10 seconds, then
•One long beep to indicate the end of the delay period
System in Standby Mode Period •Short beeps at 0.5 second interval
•Increase to 4 beeps/second at the last 10 seconds, then
•One long beep to indicate the end of the period
Note: beep halts when programming mode or battery test is
started.
System is or was in Alarm condition
(Alarm occurred) Warning beeps •4 fast beeps at 1 second interval
Successful Keypad operation
OR
Battery is Normal after Testing
•2 Short beeps
AC power Failure •1 Short beep/30 seconds
Battery Low After Testing •5 Short beeps first, then
•1 Short beep/30 seconds
Opening the cabinet
The HAM263D master control unit is protected from opening by a built-in tamper switch. Opening
the cabinet door will trigger the alarm.
•Before opening the cabinet, put the system in stand-by mode. To do this, disarm the system via
the keypad. Refer to the section on the keypad for the procedure.
•Specifications
power supply 16.5V, 3A
back-up battery requirements 7Ah, 12V, rechargeable sealed lead acid battery (not included,
e.g. WP7-12)
standby current typically 100mA
temperature range 0°C~+65°C
entry delay 15~90s
exit delay 60s
alarm duration 3~15min or infinite
power up delay (standby mode) 60s
dimensions master unit 270 x 265 x 78mm
dimensions keypad 117 x 117 x 27mm
dimensions box 346 x 540 x 152mm
weight (master unit + keypad) 2,5kg

HAM263D
00 (10/10/2008) VELLEMAN
8
2.2 Battery
To be fully reliable, the alarm system requires a back-up battery (not included). This should be a
sealed rechargeable 12V lead-acid battery with capacity 6,5~7,0Ah. Normal back-up time is about
16 hours at 250mA. Expected battery life-time is about 3 to 5 years.
Only connect the battery after all other connections have been made.
Connection
The (+) RED wire connects to the positive contact of the battery and the (-) BLACK wire connects to
the negative contact of the battery. The battery is protected by a 3A resettable fuse, and it is
charged by a current limiting regulated voltage source in the system.
Periodic test
The system performs a back-up battery test automatically once every 24 hours. The test takes from
5 seconds to 2 minutes depending on the condition of the battery.
When the battery condition is normal, 2 beeps will be produced. When a faulty condition is detected,
first 5 beeps will sound, followed by one beet every 30 seconds. The LED battery on the digital
keypad will be lit.
Manual test
The battery test can be manually initiated via a key switch (not applicable for HAM263D) or the
keypad. Refer to the keypad operations chapter for more details. The manually initiated battery test
initiates the start of a new 24 hour period
Note:
Battery test will not start or continue when an alarm condition exists or occurs, or when AC power
failure is detected.
2.3 Power supply
The power supply for the HAM263D is a general purpose AC power adaptor that provides 16,5V AC,
with a maximum output current of 3.000mA. It is designed for indoor use only.
Only connect the power plug to the mains outlet after all other connections have
been made.
•Use the mounting holes (2) to mount the adaptor in a dry location, close to a mains outlet and to
the master control unit.
•Make sure that power consumption of the connected system does not exceed the specifications of
the power adaptor.
•Connect the 16,5VAC output voltage to contacts 1 and 2 of the master control unit.
•Do not insert the power plug (1) in the mains before all necessary connections have been made
and the whole alarm system is connected.
•specifications
Input voltage 230VAC, 50Hz
Output voltage 16,5VAC
Output current 3.000mA Max.
Rated power 49,5VA
Protection Built-in thermal fuse and current fuse
Dimensions 76 x 92 x 62mm
Weight ±1.250g
Power plug CEE 7/16 (Europlug 2.5 A/250 V unearthed)
1. Power plug
2. Mounting hole
3. Power indicator
4. Power output, 16,5VAC

HAM263D
00 (10/10/2008) VELLEMAN
9
3. Sensors
Different types of sensor devices can be connected to the input relais, e.g. PIR sensor (HAA52N),
panic button (HAA60), magnetic contacts etc....
Make sure all power is removed from the system before installing (additional)
sensors!
3.1 PIR sensor (HAA52N)
The HAA52N is a passive infrared intrusion detector for general purposes, designed to give a cost-
effective and reliable solution for residential and commercial security systems.
3.1.1 Features
•dual low-noise pyro sensor
•alternate polarity signal processing
•security logics integrated into the MCU device
•SMT components for a greater EMI and RFI immunity
•normal or pulse count response
3.1.2 Coverage pattern
3.1.3 PCB description
Top view Side view
1. PCB fixing screw
2. Alarm output jumper
3. Pulse mode jumper
4. LED on/off jumper
5. Test/alarm indicator
6. Pyro sensor (do not touch!)
7. Connection terminal block
8. Tamper switch

HAM263D
00 (10/10/2008) VELLEMAN
10
Connection Terminal Description
ALARM This is the alarm relay output contact of the detector. It is selectable as NC or
NO via the alarm jumper to match the requirements of the protection zone.
DC12V Connect the positive (+) side to an 8V ~ 16V DC power source, usually from the
alarm control panel. Connect the negative (-) side to the common grounding
point of the control panel.
TAMP NC If a tamper switch is required, connect these terminals to a 24-hour NC
protection zone in the alarm control panel. The tamper switch contact is closed
with the detector’s front cover secured on the box. The opening of the front
cover at any time will make the contact open and send an immediate alarm
signal to the control panel.
Jumper Settings
LED ON Enables the LED
ON = alarm activated.
FLASH = power-up.
OFF Disables the LED. Does not affect detection.
MODE S Standard alternate polarity signal processing. For operation within a stable
environment.
P Double alternate polarity signal processing within 10 seconds. For a harsh
environment.
ALARM NC The alarm relay output contact is NC. The output relay is normally energized.
NO The alarm relay output contact is NO. The output relay is normally de-
energized.
3.1.4 Installation
a. Mounting Location
•The detector can be surface or corner mounted, or mounted with the supplies swivel bracket.
Always mount the unit on a sturdy surface.
•The detector should be mounted indoors, in areas that do not have openings constantly exposed
to the outside environment.
•Select the mounting location so that the expected movement of an intruder will cross the
detection beam.
•Do not locate the detector where hot or cold moving air will blow directly onto the unit.
•Avoid aiming the detector towards heating or air conditioning vents or ducts, exterior metal
walls, exterior windows or curtains covering windows, refrigerator or freezer grills or other
surfaces that may change temperature rapidly.
•Avoid putting large objects in front of the detector which will cause significant changes in the
area or volume protected.
•Select the mounting location so that the beam patterns are at a 45° angle to the intruder’s
expected path. Installation height should be 2 ~ 3m.
b. Front Cover Removal
Loosen the screw on the bottom of the box to release the front cover from the rear cover.
c. PCB Removal
It is necessary to remove the PCB before mounting the rear cover. Loosen the PCB fixing screw.
Pull out the PCB carefully.
d. Rear Cover Mounting
The rear cover is prepared for either surface or corner mounting, or mounting with the supplied
swivel bracket.
•Punch the cable hole at the back of the rear cover, together with the fixing holes (knockout
holes) according to the mounting (surface or corner mounting, or mounting with the supplied
swivel bracket).
•Mount the rear cover or mount the swivel bracket with screws (mount the rear cover on the
swivel bracket afterwards).