Velleman CCTVPROM16 User manual

CCTVPROM16
CCTV PACK – H.264 FULL FRAME DVR - 4 IR CAMERAS – 500 GB HARD DISK
CCTV-PACK – H.264 FULL FRAME DVR - 4 IR-CAMERA'S - HARDE SCHIJF 500GB
PACK VIDEOSURVEILLANCE – DVR H.264 PLEIN ÉCRAN - 4 CAMÉRAS IR - DISQUE
DUR 500GO
JUEGO DE VIGILANCIA - H.264 VIDEOGRABADORA FULL FRAME - 4 CÁMARAS IR -
DISCO DURO 500GB
CCTV-PACK - H.264 FULL FRAME VIDEORECORDER - 4 IR-KAMERAS - FESTPLATTE
500GB
CONJUNTO CCTV - H.264 FULL FRAME DVR - 4 CÂMARAS IR – DISCO RIGIDO
500GB
ZESTAW MONITORINGOWY- H.264 FULL FRAME DVR - 4 KAMERY IR - HD 500GB
QUICK INSTALLATION GUIDE 3
BEKNOPTE INSTALLATIEHANDLEIDING 11
GUIDE D'INSTALLATION RAPIDE 19
GUÍA RÁPIDA 27
SCHNELLEINSTIEG 35
GUIA RÁPIDO PARA INSTALAÇÃO 43
SKRÓCONA INSTRUKCJA INSTALACJI 51

CCTVPROM16
V. 02 – 21/08/2013 2 ©Velleman nv
EN
1
DC 12V input terminal
2
Video output connector
NL
1
DC 12V ingangsaansluiting
2
Video-uitgangsaansluiting
FR
1
Connexion d’entrée CC 12V
2
Connexion de sortie vidéo
DE
1
DC 12V-Eingangsanschluss
2
Video-Ausgangsanschluss
ES 1 Conexión de entrada CC 12V PT 1 Terminal de entrada DC 12V
PL
1 Wejście zasilania DC 12 V
2 Conexión de salida de vídeo
2 Conector de saída de vídeo
2 Złącze wyjściowe wideo

CCTVPROM16
V. 02 – 21/08/2013 3 ©Velleman nv
QUICK INSTALLATION GUIDE
1. Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle could
harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should
be taken to a specialized company for recycling. This device should be returned to your distributor or to
a local recycling service. Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing Velleman! Please read the manual thoroughly before bringing this device into service. If
the device was damaged in transit, don't install or use it and contact your dealer.
Notes
•This document is a quick installation guide. For more detailed information, refer to the full user manual on
the included CD-ROM.
•Product images are for illustrative purposes only. Due to constant product improvements, the actual
product may differ from the images.
Package content:
•1 x DVR with built-in SATA connection: DVR4H3
•4 x IR colour cameras: CAMCOLBUL29
•4 x 20 m camera cables
•1 x 19 V power supply
•1 x high-efficiency DC-DC converter for DVR and cameras
•hard disk (built in): HD500GB/S
•remote control: DVRRC4
2. Safety Instructions
Keep the device away from children and unauthorised users.
Risk of electroshock when opening the cover. Touching live wires can cause life-threatening
electroshocks.
Always disconnect mains power when the device is not in use or when servicing or maintenance
activities are performed. Handle the power cord by the plug only.
3. General Guidelines
Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.
Indoor use only
Keep this device away form rain, moisture, splashing and dripping liquids. Never put object
s
filled with liquid on top.
Keep this device away from dust.
Keep this device away from extreme heat. Make sure the ventilation openings are clear at
all times. For sufficient air circulation, leave at least 1” (±2.5 cm) in front of the openings.
Protect this device from shocks and abuse. Avoid brute force when operating the device.
•Familiarise yourself with the functions of the device before actually using it.
•All modifications of the device are forbidden for safety reasons.
•Only use the device for its intended purpose. Using the device in an unauthorised way will void the
warranty.

CCTVPROM16
V. 02 – 21/08/2013 4 ©Velleman nv
•Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the
dealer will not accept responsibility for any ensuing defects or problems.
•Do not use this product to violate privacy laws or perform other illegal activities.
4. Overview
Refer to the illustrations on page 2of this manual.
Front panel
LED indications
HDD reading or recording activities on the hard disk
ALARM
an alarm was triggered
TIMER timed recording is enabled
PLAY
the DVR is in playing mode
POWER DVR power is on
NAVIGATE
Press one of the four positions on the navigate button to move the cursor up
(), down ( ), left ( ) or right ( ).
In play-back mode, press the buttons to play/pause ( ), stop ( ), fast
rewind ( ) or fast forward ( ) the play-back file.
In setting mode, press the up ( ) or down ( ) button to change the
setting in the menu.
MENU
Press to enter the main menu.
ENTER Press to confirm settings
LIST
List the information of the recorded files.
QUICK SEARCH / RECORD / MOTION / ALARM / TIMER / FULL LIST
PLAY
Press to play the recorded video.
SLOW
In playback mode, press to play the recorded file slowly.
ZOOM
In live or playback mode, press to enlarge the image of the selected channel.
SEQ Press to show all screens sequentially in full screen mode. Press again to quit.
4CH: Press to show the 4 channel display mode.
1 ~ 4
Press a button to select the corresponding channel.
SEARCH
Enter time search mode. Set time range and press START to see all recordings within the time
range.
AUDIO
= SLOW + ZOOM
Press SLOW and ZOOM simultaneous to select live or play-back sounds.
PTZ
(pan tilt zoom) = SLOW +
Press SLOW and simultaneous to enter or exit PTZ control mode.
USB port
(2x)
Connect a USB flash drive for video backup to one USB port; connect a USB mouse to the
other.
Note: do not connect two USB flash drives or USB mice at the same time.
Rear panel
LAN port Connect the DVR to a local network by plugging a network cable into this port.
VGA
connector for video monitor (monitor not included)
AUDIO IN
4 audio input channels to connect four external audio sources e.g. from cameras with audio.
AUDIO OUT
1 audio output to connect to an audio device, e.g. a speaker (mono).
VIDEO IN
4 video input channels to connect 4 external video sources e.g. cameras.
VIDEO OUT 1 video output channel to connect the DVR to the main monitor.
EXTERNAL I/O
use a 9 pin DSUB connector to connect external signals, for example alarm, PTZ…

CCTVPROM16
V. 02 – 21/08/2013 5 ©Velleman nv
power switch
19V DC
power supply input
5. Hardware setup
Installing the hard disk drive (HDD)
The DVR has a built-in hard disk. To install another hard disk, proceed as follows:
1. Obtain a suitable HDD (see Technical Specifications below), type SATA. The HDD must be formatted.
2. Unplug the device from the mains before servicing and do not touch any electronic circuitry to avoid
electrostatic discharge.
3. Unscrew the 6 screws (1 on either side and 4 on the back) that hold the cover in place.
4. Lift the cover (back first).
5. Remove the hard disk.
6. Screw the mounting brackets on the new hard disk (screws included).
The PCB must be facing upwards when mounting the HDD into the DVR.
7. Connect the SATA data cable and power supply to the HDD.
8. Screw the HDD on the bottom of the DVR housing PCB facing upwards using the included screws.
9. Close the cover (front first) and secure it with the 6 screws.
Connecting a video monitor
•Obtain a suitable monitor (not included) and connect it to the BNC or VGA video output port on the back of
the DVR.
Connecting the power supply
1. Plug the DC output connector of the included power adaptor into the 19VDC power input at the back of
the DVR.
WARNING: only use the included adaptor.
2. Plug the included power cable into the adaptor input connector and plug the other end into the mains.
Do not switch the DVR on yet.
Connecting a camera
1. The CCVT pack comes with 4 cameras. Each camera needs its own power supply.
2. Connect the video output of the camera to either video input at the back of the DVR. The number next to
the input connectors represents the channel number. Connector type is BNC.
Connecting audio
1. The DVR supports four audio inputs. Connect the audio output of an audio source to an audio input of the
DVR. Make sure to connect the audio channel to the corresponding video channel. Connector type is BNC.
2. There is also an audio output connector. Connect an audio device e.g. a speaker to this connector when
desired. Connector type is BNC.
Connecting Local Area Network (LAN)
•Connect the DVR to a local network by plugging a network cable into the LAN port at the back of the DVR.
Connector type is 8P8C (RJ45). Setup is done through the OSD.
6. Preliminary settings
Make sure the connected cameras are on and set the power switch at the rear of the device to the ON position.
It takes about 15 to 30 seconds to start up.
Menu overview
Press the MENU button and enter the password to go into the menu list.
Note: default admin password is “0000” (4 times zero).

CCTVPROM16
V. 02 – 21/08/2013 6 ©Velleman nv
QUICK START
GENERAL - TIME SETUP
DATE SETUP
DATE INFO - DAYLIGHT
SYSTEM
TOOLS - SYSTEM INFO – BACKUP DATA – BACKUP LOG
EVENT
INFORMATION
QUICK SEARCH - EVENT SEARCH - HDD INFO - EVENT LOG
ADVANCED
CONFIG
CAMERA – DETECTION – ALERT – NETWORK – DISPLAY – RECORD - REMOTE
SCHEDULE
SETTING RECORD – DETECTION – ALARM
For more detailed information, refer to the full user manual on the included CD-ROM.
Setting date and time
Before using the DVR the time and date should be set to get a valid time stamp.
1. Press the MENU button and enter the admin password to go into the menu list.
2. Select the QUICK START menu item.
3. Use the NAVIGATION button to move to the TIME SETUP menu item. Select it to set date and time.
Note: once recording started, do not change date or time as this will make it very difficult to find back the
recorded files.
Note: when using the DVR for the first time and the correct time is set, leave it on for at least 48 hours.
Password setting
1. Press the MENU button and enter the password to go into the menu list.
2. Select the SYSTEM menu item.
3. Go to TOOLS. Select ADMIN PASSWORD (or OPERATOR PASSWORD) and press the ENTER button to set the
password.
Note: an operator can not access the main menu, only the quick menu bar (see below).
4. Press the cursor up ( ) or down ( ) button to select the value of the first number and press enter to
save and go to the next character, or use the mouse to select the desired value. Repeat this for all four
password numbers.
Note: default admin password is “0000” (4 times zero).
Record settings
1. Press the MENU button and enter the password to go into the menu list.
2. Select the QUICK START menu item.
3. Select the GENERAL menu item using the NAVIGATION button.
4. Set the image size, image quality and images per second for recording.
5. Refer to the full user manual on the included CD-ROM for more details.

CCTVPROM16
V. 02 – 21/08/2013 7 ©Velleman nv
Audio playback
Press the SLOW and ZOOM button simultaneously to select the desired audio channel or use the quick menu
bar (see below). The current audio channel is indicated in the status bar.
Switch users
1. The DVR can be accessed as administrator ( ) or operator ( ), icons are indicated in the status bar.
2. To switch between users, click on the user icon ( or ) to lock the current session ( ).
3. Press on the key lock icon ( ) than enter the password of the desired profile.
7. Operation
7.1 Display
The following image shows the screen layout.
A system date and time
B
general system status
C available HDD capacity
D
channel status
live audio channel 1 .. 4 enabled playback audio channel 1 .. 4 enabled (yellow)
audio channel disabled timer recording
digital zoom on (yellow) / off USB mouse connected
LAN connected / Internet connected / no network connection
USB flash drive connected Hard disk overwrite (default)
key lock on PTZ mode
sequence mode motion mode
recording mode
alarm mode
administrator logged on operator logged on
Note that actual screen icons might differ slightly from the ones shown above.
7.2 Quick menu bar
Note: only available when USB mouse is connected.
Move the pointer towards the left of the monitor to open the quick menu bar:

CCTVPROM16
V. 02 – 21/08/2013 8 ©Velleman nv
Open channel switch panel.
Show playback control panel.
Zoom-in mode (select desired channel first before entering zoom-mode).
Select audio channel (live mode only live channels can be selected).
Enter PTZ mode and show PTZ control panel
Click to show the power off panel to either halt or reboot the system.
7.3 Recording
•Check whether the camera(s) is (are) properly connected and a HDD is present inside the device.
•When the auto-recording and pre-alarm functions are enabled, the device will start recording images.
•Default the recording icon ( ) is shown.
•In case the motion or alarm detection is activated and a motion or alarm is detected, the motion ( ) resp.
alarm ( ) icon is shown.
•When timed recording is enabled, the timed recording icon ( ) is shown and the timed recording LED
is on.
•Default, the device is in HDD overwrite mode and the icon ( ) is shown.
7.4 Play-back
Make sure the control panel is not locked and press the PLAY button on the control panel or use the quick menu
bar to open the playback control panel:
A
progress bar
D
information
B
playback control
E
close
C
event search
F
set repeat function A→B / open backup menu
Note: play-back needs at least 8192 recorded images to work properly (e.g. with IPS=30, the recording must
be at least 273 seconds long).
•The fast forward ( ) and fast rewind ( ) buttons will increase resp. decrease the play-back speed.
Repeatedly pressing the button will increase/decrease speed to 4x, 8x 16x or 32x (max.).
•Press the pause button () to temporary suspend video play-back.
•Press the stop button () to return to live monitoring.
•Press the SLOW button once to set play-back speed to 1/4th and twice for 1/8th.
7.5 Search
•There are four ways to search recorded files: by record list, motion list, alarm list or by timer list.
•To search an event, press the LIST button on the front panel (make sure the control panel is not locked).
An overview of the recorded file types (ALARM, MANUAL, MOTION, SYSTEM and FULL LIST) is shown.
•Select the desired list and recording from the list.

CCTVPROM16
V. 02 – 21/08/2013 9 ©Velleman nv
•Press ENTER to start play-back.
8. Technical Specifications
video format PAL
video compression
H.264
video input
4 channels, composite video signal 1 Vpp / 75 ohm BNC
video output composite video signal 1 Vpp / 75 ohm BNC + VGA
maximum recording rate (PAL)
- frame: 704 x 576 pixels with 100 IPS (PAL)
- CIF: -
image quality setting super best - best - high - normal
hard disk storage
built-in SATA type, support 1 x HDD, support HDD capacity over 2 TB (500 GB
hard disk included)
recording mode
manual / timer / motion / network / alarm controlled
refresh rate
100 IPS for PAL
multiplex operation
live display, record, playback, backup and network
audio I/O 4x audio in, 1x audio out (mono)
motion detection area
16 x 12 grids per channel
motion detection sensitivity high - normal - low
pre-alarm recording
8 MB
backup device USB 2.0 flash drive (for backup and firmware updates)
Central Management System
remote surveillance to monitor up to 10 different IP addresses (Windows &
Mac OS)
web transmitting / compression
format
H.264
Ethernet 10/100BASE-T, supports remote control and LiveView via Ethernet
mobile surveillance
Smartphones:
EagleEyes software: remote login via all smartphone platforms
(Apple, Android, BlackBerry, Nokia Symbian and Windows Mobile)
computer:
- video viewer software on Windows and Mac
-
web browser: Internet Explorer, Firefox, Google Chrome and Safari via Java,
Quicktime or VLC plug-in
network connection supports TCP/IP, PPPoE, DHCP and DDNS function
IR remote control
remote control DVR and PTZ (DVRRC4)
PTZ control
yes (via RS-485)
alarm I/O
4 in / 1 out
digital zoom
2x (live & playback)
key lock
yes
video loss detection
yes
camera title up to 6 characters
video adjustments
hue / colour / contrast / brightness
date display format
YY/MM/DD, DD/MM/YY, MM/DD/YY, and off
power source
19 VDC
power consumption < 42 W
daylight saving
yes
operating temperature
10-40 °C (50-104 °F)
system recovery system auto recovery after power reconnected
dimensions
343 x 59 x 223 mm
IR camera
pick-up element
1/3" colour CCD image sensor
number of pixels 712 (H) x 582 (V) - PAL -
resolution
420 TV lines

CCTVPROM16
V. 02 – 21/08/2013 10 ©Velleman nv
min. illumination
0.05 lux (F2.0); 0 lux (IR on)
IR LEDs
14
range (IR light)
15 m
S/N ratio
> 48 dB (AGC off)
water resistance IP67
electronic shutter
1/50 to 1/100 000 s
lens angle
92.6°
white balance
automatic
AGC yes
standard board lens
f3.6mm / F2.0
video output
1.0 Vpp composite, 75 ohm
power supply DC 12 V ± 10 %
current consumption
70 mA (IR off), 200 mA (IR on)
dimensions Ø 60 x 91 mm
weight
250 g (including bracket)
Use this device with original accessories only. Velleman nv cannot be held responsible in the event
of damage or injury resulting from (incorrect) use of this device.
For more info concerning this product and the latest version of this manual, please visit our website
www.velleman.eu.
The information in this manual is subject to change without prior notice.
© COPYRIGHT NOTICE
The copyright to this manual is owned by Velleman nv. All worldwide rights reserved. No part of this
manual may be copied, reproduced, translated or reduced to any electronic medium or otherwise without the
prior written consent of the copyright holder.