VeriFone 55225 User manual

Mobil Indoor Speedpass
Installation Guide
P/N: 55225
Revision A

Mobil Indoor Speedpass Installation Guide
September 11, 1998
VeriFone®, Inc.
4988 Great America Parkway
Santa Clara, CA 95054-1200
Telephone: [phone]
http://www.verifone.com
Printed in the United States of America.
© 1998 by VeriFone, Inc. All rights reserved.
No part of this publication covered by the copyrights herein may be
reproduced or copied in any form or by any means — graphic,
electronic, or mechanical, including photocopying, taping, or
information storage and retrieval systems — without written permission
of the publisher.
The content of this document is subject to change without notice. The
information contained herein does not represent a commitment on the
part of VeriFone, Inc.
Publications are not stocked at the address given above. Requests for
VeriFone publications should be made to your VeriFone representative.
VeriFone is a registered trademark of VeriFone, Inc. Speedpass is a
trademark of Mobil Oil Corporation. All other products mentioned in
this manual are trademarks or registered trademarks of their respective
owners.

Mobil Indoor Speedpass Installation Guide
Revision History
Revision Date Comments
A September 11, 1998 Initial release of software
and documentation.

FCC Compliance
This equipment complies with the requirements in Part 15 of FCC
rules for a Class A computing device. Operation of this equipment
in a residential area may cause unacceptable interference for radio
and TV reception requiring the operator to take whatever steps
necessary to correct the interference.
Safety Instructions
■Read all instructions contained in this guide before making
any equipment connections.
■Save these instructions for later use.
■Unplug the unit before servicing or cleaning. Do not use
liquid or aerosol cleaners. Use only a damp cloth for
cleaning.
■Do not use any attachments not specifically recommended
by VeriFone as they may result in the risk of fire, electric
shock, or injury to persons.
■Do not use the unit near water.
■Do not place the unit on an unstable cart, stand, or table.
The unit may fall, causing serious personal injury and/or
damage to the equipment.

Contents ◆i
Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . .1
2. Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . .3
3. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Installation Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Equipment Power Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
4. Specifications. . . . . . . . . . . . . . . . . . . . . . . . .9
Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Operating Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Service and Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

ii ◆Contents

Introduction ◆1
1Introduction
This document provides the information necessary to install your
Mobil Indoor Speedpass System.
The Mobil Indoor Speedpass System is a self-contained device,
when properly installed, becomes an integral part of the POS
equipment. It has the ability of reading a retail customer’s tag when
placed near an antenna mounted on the face of the equipment.
n
mobilind.wmf 125%
Soft Key Guard
Card Swipe Guard
Multicable
Power Supply
Mobil Indoor
Speedpass

2◆Introduction
Information from the tag is processed and transferred to POS
equipment.

Unpacking ◆3
2Unpacking
Carefully inspect the shipping carton and its contents for any
damage that may have occurred during shipment. If anything
appears damaged, immediately file a claim with the shipping
company or carrier and notify the Point of Sales equipment
manufacturer.
Warning: Never use damaged equipment. A shock or fire
hazard may exist if equipment is energized in a
damaged condition.
Remove the following items from the shipping carton:
■Mobil Indoor Speedpass Unit with attached Mulitcable
■Power Supply
■Soft Key Guard
■Card Swipe Guard
Remove any protective plastic wrapping from the components and
place them on a table or countertop.
Retain the shipping carton and any packing material in case it is
necessary to move components from one location to another or to
return the equipment for service.

4◆Unpacking