Vertiv NetSure 211 Series User manual

NetSure™ 211 Series
-48 VDC Battery Cabinet
Installation and User Manual
Specification Number: 554631
Model Number: 211BC

Vertiv™ NetSure™ 211 Series -48 VDC Battery Cabinet Installation and User Manual
Vertiv™ NetSure™ 211 Series -48 VDC Battery Cabinet Installation and User Manual
The information contained in this document is subject to change without
notice and may not be suitable for all applications. While every precaution has
been taken to ensure the accuracy and completeness of this document, Vertiv
assumes no responsibility and disclaims all liability for damages resulting from
use of this information or for any errors or omissions. Refer to other local
practices or building codes as applicable for the correct methods, tools, and
materials to be used in performing procedures not specifically described in
this document.
The products covered by this instruction manual are manufactured and/or
sold by Vertiv. This document is the property of Vertiv and contains
confidential and proprietary information owned by Vertiv. Any copying, use or
disclosure of it without the written permission of Vertiv is strictly prohibited.
Names of companies and products are trademarks or registered trademarks of
the respective companies. Any questions regarding usage of trademark
names should be directed to the original manufacturer.
Technical Support Site
If you encounter any installation or operational issues with your product, check the pertinent section of this
manual to see if the issue can be resolved by following outlined procedures.
Visit https://www.vertiv.com/en-us/support/ for additional assistance.

Vertiv™ NetSure™ 211 Series -48 VDC Battery Cabinet Installation and User Manual
Proprietary and Confidential © 2022 Vertiv Group Corp.
iii
TABLE OF CONTENTS
Admonishments Used in this Document.............................................................................................................................iv
Important Safety Instructions..................................................................................................................................................v
Safety Admonishments Definitions ..........................................................................................................................................................................................................................v
Safety and Regulatory Statements...........................................................................................................................................................................................................................v
Déclarations de Sécurité et de Réglementation...........................................................................................................................................................................................v
1Introduction...............................................................................................................................................................................1
1.1 Description...........................................................................................................................................................................................................................................................................1
1.2 Batteries..................................................................................................................................................................................................................................................................................1
1.3 Specifications....................................................................................................................................................................................................................................................................2
2Installation ................................................................................................................................................................................2
2.1 Important Safety Instructions............................................................................................................................................................................................................................2
2.2 General Requirements..............................................................................................................................................................................................................................................2
2.3 Mounting the Battery Cabinet ..........................................................................................................................................................................................................................2
2.3.1 Relay Rack Method...............................................................................................................................................................................................................................3
2.3.2 Wall Method.................................................................................................................................................................................................................................................3
2.4 Connecting Battery Cabinet(s) to the Associated Power System..................................................................................................................................5
2.5 Installing GNB M12V40F Batteries................................................................................................................................................................................................................7
2.6 Securing the Batteries Using the Strap....................................................................................................................................................................................................9
2.7 Typical Internal Wiring Layout.......................................................................................................................................................................................................................10

Vertiv™ NetSure™ 211 Series -48 VDC Battery Cabinet Installation and User Manual
Proprietary and Confidential © 2022 Vertiv Group Corp.
iv
Admonishments Used in this Document
DANGER!
Warns of a hazard the reader will be exposed to that will likely result
in death or serious injury if not avoided. (ANSI, OSHA)
WARNING!
Warns of a potential hazard the reader may be exposed to that could
result in
death or serious injury if not avoided. This admonition is not used for situations that pose a
risk only to equipment, software, data, or service. (ANSI)
CAUTION!
Warns of a potential hazard the reader may be exposed to that could
result in minor or moderate injury if not avoided. (ANSI, OSHA) This admonition is not
used for situations that pose a risk only to equipment, data, or service, even if such use
appears to be permitted in some of the applicable standards. (OSHA)
ALERT!
Alerts the reader to an action that must be avoided in order to protect
equipment, software, data, or service. (ISO)
ALERT!
Alerts the reader to an action that must be performed in order to prevent
equipment damage, software corruption, data loss, or service interruption. (ISO)
FIRE SAFETY!
Informs the reader of fire safety information, reminders, precautions,
or policies, or of the locations of fire
-fighting and fire-safety equipment. (ISO)
SAFETY!
Informs the reader of general safety information, reminders, precautions, or
policies not related to a particular source of hazard or to fire safety. (ISO, ANSI, OSHA)

Vertiv™ NetSure™ 211 Series -48 VDC Battery Cabinet Installation and User Manual
Proprietary and Confidential © 2022 Vertiv Group Corp.
v
Important Safety Instructions
Safety Admonishments Definitions
Definitions of the safety admonishments used in this document are listed under “Admonishments Used in this Document” on page iv.
Safety and Regulatory Statements
Refer to Section 4154 (provided with your customer documentation) for Safety and Regulatory Statements.
Déclarations de Sécurité et de Réglementation
Reportez-vous à la Section 4154 (fourni avec les documents de votre client) pour les déclarations de sécurité et de réglementation.

Vertiv™ NetSure™ 211 Series -48 VDC Battery Cabinet Installation and User Manual
Proprietary and Confidential © 2022 Vertiv Group Corp.
vi
This page intentionally left blank.

Vertiv™ NetSure™ 211 Series -48 VDC Battery Cabinet Installation and User Manual
Proprietary and Confidential © 2022 Vertiv Group Corp.
1
1Introduction
1.1 Description
The Vertiv™ NetSure™ 211 Series -48 VDC battery cabinet can be mounted in a 19” or 23” relay rack or mounted to a wall. The battery
cabinet contains one (1) 40 A battery disconnect circuit breaker and provides alarm leads attached to the common contacts of the
breaker.
Battery cabinets may be daisy chained as shown in Figure 2.5 to increase the reserve time. However, a maximum system current of
30 amps should be maintained regardless of the number of interconnected cabinets.
Figure 1.1 Vertiv™ NetSure™ 211 Series -48 VDC Battery Cabinet
1.2 Batteries
The battery cabinet is designed to hold the batteries listed in Table 1.1.
Table 1.1 Batteries
Battery
Manufacturer
Manufacturer
P/N
Vertiv
P/N
Weight (lbs.)
per Battery
GNB M12V40F 241173815 39.0

Vertiv™ NetSure™ 211 Series -48 VDC Battery Cabinet Installation and User Manual
Proprietary and Confidential © 2022 Vertiv Group Corp.
2
1.3 Specifications
Environmental Ratings
•Operating Ambient Temperature Range: -40 °C to +65 °C.
•Storage Ambient Temperature Range: -40 °C to +85 °C.
•Humidity: This unit is capable of operating in an ambient relative humidity range of 0% to 95%, non-condensing.
•Altitude: The maximum operating ambient temperature should be derated by 10 °C at an elevation of 10,000 feet above sea
level. For elevations between 3,000 feet and 10,000 feet, derate the maximum operating ambient temperature linearly.
Overall Dimensions
Battery cabinet dimensions are illustrated in Figure 1.2.
Figure 1.2 Battery Cabinet Dimensions
2Installation
2.1 Important Safety Instructions
DANGER! Adhere to the “Important Safety Instructions” starting on page v.
2.2 General Requirements
The installer should be familiar with the installation requirements and techniques to be used in securing the battery cabinet to a relay
rack or wall.
2.3 Mounting the Battery Cabinet
The battery cabinet is designed to mount on a wall or a standard 19” or 23” wide relay rack.
17.50”
10.25”
14.80”

Vertiv™ NetSure™ 211 Series -48 VDC Battery Cabinet Installation and User Manual
Proprietary and Confidential © 2022 Vertiv Group Corp.
3
2.3.1 Relay Rack Method
Procedure
1. Refer to Figure 2.1 and install the 19” or 23” relay rack mounting angles to the battery cabinet. Mounting hardware is provided
with the battery cabinet. Torque these connections to 46 in-lbs.
NOTE! There are three mounting locations for the mounting angles providing different projections in front of the relay rack.
Figure 2.1 Installing Mounting Angles on the Battery Cabinet
2. Install battery retention strap through openings in rear of cabinet. Orient the buckle per Figure 2.9.
3. Secure the battery cabinet to the relay rack with the provided 12-24 x 1/2” hex head thread-forming screws (ten per side)
(P/N 218710500) and #12 ground washers (five per side) (P/N 215640600).Torque these connections to 35.0 in-lbs.
2.3.2 Wall Method
WARNING! Ensure the technique and hardware used in securing the battery cabinet can support the total weight of the
battery cabinet and the four (4) batteries. Refer to “Batteries” on page 1for a battery weight reference table. If being
mounted to a stud wall, the cabinet must be fastened to the studs. Failure to mount the cabinet correctly may result in
serious personal injury or equipment damage.
Procedure
1. Ensure that connector, wires and bushing located at the back are moved to the side, as shown in Figure 2.2, before mounting
the cabinet.
2. Install battery retention strap through openings in rear of cabinet. Orient the buckle per Figure 2.9.

Vertiv™ NetSure™ 211 Series -48 VDC Battery Cabinet Installation and User Manual
Proprietary and Confidential © 2022 Vertiv Group Corp.
4
Figure 2.2 Connectors and Wires Moved to the Side
3. Install the frame ground landing point adapter P/N 556872 to the left or right side of the battery cabinet, as shown in Figure
2.3.
Figure 2.3 Installing P/N 556872 Frame Ground Landing Point Adapter
4. Mount the battery cabinet to a wall through the six 0.406” diameter holes on the back of the cabinet, as shown in Figure 2.4.
If mounting to a stud wall, secure the battery cabinet to the studs.
5. Ensure the technique and hardware used in securing the cabinet can support the total weight of the cabinet and the
batteries. Refer to “Batteries” on page 1 for a battery weight reference table.
Frame Grounding Point
(1/4-20 Studs on 5/8” Centers)
(Torque to 75 in-lbs)
Attach Frame Ground Landing
Point Adapter to Cabinet
(Torque to 46 in-lbs)

Vertiv™ NetSure™ 211 Series -48 VDC Battery Cabinet Installation and User Manual
Proprietary and Confidential © 2022 Vertiv Group Corp.
5
Figure 2.4 Mounting the Battery Cabinet to a Wall
2.4 Connecting Battery Cabinet(s) to the Associated Power System
Battery Leads
Cables with connectors are provided on the associated power system and the battery cabinet to allow simple interconnections
between a battery cabinet and the associated power system and between battery cabinets. The battery cabinet is designed to be
daisy-chained together with additional battery cabinets. There is no limit to the number of battery cabinets that can be connected
together. However, a maximum system current of 30 A should be maintained regardless of the number of interconnected battery
cabinets.
Procedure
NOTE! Refer to Figure 2.5 as this procedure is performed.
1. Connect the power system’s battery cable terminated in an Anderson connector to the first battery cabinet’s battery cable
terminated in a mating Anderson connector.
2. Connect the second battery cabinet’s battery cable terminated in an Anderson connector to the fixed mating Anderson
connector located on the first battery cabinet.
3. Repeat the above step if there are additional battery cabinets.
WALL
0.406”
mounting holes

Vertiv™ NetSure™ 211 Series -48 VDC Battery Cabinet Installation and User Manual
Proprietary and Confidential © 2022 Vertiv Group Corp.
6
Figure 2.5 Connecting Multiple Battery Cabinets
Battery Disconnect Circuit Breaker Alarm Leads
Procedure
1. Furnished with the battery cabinet are battery disconnect circuit breaker alarm lead assemblies. Refer to the power system
installation manual to use these alarm leads to connect the battery cabinet battery disconnect circuit breaker alarm into the
power system alarm circuits.
NOTE! Supplied with the battery cabinet is a yellow alarm lead assembly P/N 545696 and an orange alarm lead assembly
P/N 565513. P/N 545696 is always used. P/N 565513 is used only with power systems containing a 1M831ANA Mini Controller
(may be discarded if battery cabinet is used with other systems).
POWER SHELF
BATTERY CABINET
MAIN
BATTERY CABINET
SUPPLEMENTAL
(OPTIONAL)
BATTERY CABINET
SUPPLEMENTAL
(OPTIONAL)

Vertiv™ NetSure™ 211 Series -48 VDC Battery Cabinet Installation and User Manual
Proprietary and Confidential © 2022 Vertiv Group Corp.
7
2.5 Installing GNB M12V40F Batteries
Procedure
1. Unscrew the front cover panel from the battery cabinet.
2. Place the spacers in between the batteries. Refer to Figure 2.6.
NOTE! Place the two supplied spacers (P/N 545511) side by side, and follow with the other spacer (P/N 545538) on top.
Figure 2.6 Placing GNB M12V40F Batteries
3. Connect all four GNB batteries using supplied wires (Part Number 545529) crimped with 12-10 AWG ring lug on each end, as
shown in Figure 2.7.

Vertiv™ NetSure™ 211 Series -48 VDC Battery Cabinet Installation and User Manual
Proprietary and Confidential © 2022 Vertiv Group Corp.
8
Figure 2.7 Connecting GNB M12V40F Batteries
4. Attach the cabinet wires to + and - terminals. Refer to Figure 2.8.
Figure 2.8 Connecting GNB M12V40F Batteries to (+) and (-) Terminals
5. Refer to “Securing the Batteries Using the Strap” on page 9 for instructions on securing the batteries using the buckle strap
that is bundled along with the cabinet.
+ Wire
- Wire
Supplied
cables
Anderson
connector
Circuit
breaker
* Top cover removed
in illustration for clarity.

Vertiv™ NetSure™ 211 Series -48 VDC Battery Cabinet Installation and User Manual
Proprietary and Confidential © 2022 Vertiv Group Corp.
9
2.6 Securing the Batteries Using the Strap
Procedure
1. Pull strap such that enough length is provided to secure the batteries.
2. Hold the buckle such that the strap can slip into inner slot of the buckle. See Figure 2.9 for reference.
Figure 2.9 Slipping the Strap into the Buckle
3. Then loop the strap into the outer slot of the buckle. Refer to Figure 2.10.
Figure 2.10 Looping the Strap into the Buckle
4. Pull again the strap to tighten.
5. Rotate buckle cover to closed position to apply and lock in tension. See Figure 2.11.
6. There should be a gap of 1/4" to 1/2" between the strap and the batteries when the buckle assembly is pulled with light finger
pressure. This will ensure the proper tension is applied to the strap.

Vertiv™ NetSure™ 211 Series -48 VDC Battery Cabinet Installation and User Manual
Proprietary and Confidential © 2022 Vertiv Group Corp.
10
7. To release buckle, pull outward on free strap end.
Figure 2.11 Securing the Batteries in the Cabinet
2.7 Typical Internal Wiring Layout
Figure 2.12 Typical Internal Wiring Layout
FIXED CONNECTOR:
INPUT FROM SUPPLEMENTARY
BATTERY CABINETS
PIGTAIL CONNECTOR:
OUTPUT TO POWER SHELF OR
OTHER BATTERY CABINET
TO -48V RESISTIVE BATTERY
BREAKER ALARM
C
NO
NC
CB
BATT
BATT
BATTBATT
49.9 ohm
TO SUPPLEMENTAL
BATTERY CABINET

Vertiv™ NetSure™ 211 Series -48 VDC Battery Cabinet Installation and User Manual
Proprietary and Confidential © 2022 Vertiv Group Corp.
Connect with Vertiv on Social Media
https://www.facebook.com/vertivI
https://www.instagram.com/vertiv/
https://www.linkedin.com/company/vertiv/
https://www.twitter.com/vertiv/

Vertiv.com | Vertiv Headquarters, 1050 Dearborn Drive, Columbus, OH, 43085, USA
© 2022 Vertiv Group Corp. All rights reserved. Vertiv™ and the Vertiv logo are trademarks or registered trademarks of Vertiv Group
Corp. All other names and logos referred to are trade names, trademarks or registered trademarks of their respective owners. While
every precaution has been taken to ensure accuracy and completeness here, Vertiv Group Corp. assumes no responsibility, and
disclaims all liability, for damages resulting from use of this information or for any errors or omissions. Specifications, rebates and
other promotional offers are subject to change at Vertiv’s sole discretion upon notice.
UM554631_REVG
Proprietary and Confidential © 2022 Vertiv Group Corp.