Vertiv NetSure 5100 Series User manual

NetSure™ 5100 Series
-48 VDC Power System
Installation Manual
Specification Number: 582137100
Model Number: 5100

Vertiv™ NetSure™ 5100 Series -48 VDC Power System Installation Manual
Vertiv™ NetSure™ 5100 Series -48 VDC Power System Installation Manual
The information contained in this document is subject to change without
notice and may not be suitable for all applications. While every precaution has
been taken to ensure the accuracy and completeness of this document, Vertiv
assumes no responsibility and disclaims all liability for damages resulting from
use of this information or for any errors or omissions. Refer to other local
practices or building codes as applicable for the correct methods, tools, and
materials to be used in performing procedures not specifically described in
this document.
The products covered by this instruction manual are manufactured and/or
sold by Vertiv. This document is the property of Vertiv and contains
confidential and proprietary information owned by Vertiv. Any copying, use or
disclosure of it without the written permission of Vertiv is strictly prohibited.
Names of companies and products are trademarks or registered trademarks of
the respective companies. Any questions regarding usage of trademark
names should be directed to the original manufacturer.
Technical Support Site
If you encounter any installation or operational issues with your product, check the pertinent section of this
manual to see if the issue can be resolved by following outlined procedures.
Visit https://www.vertiv.com/en-us/support/ for additional assistance.

Vertiv™ NetSure™ 5100 Series -48 VDC Power System Installation Manual
Proprietary and Confidential © 2023 Vertiv Group Corp.
iii
TABLE OF CONTENTS
Admonishments Used in this Document.............................................................................................................................vi
Important Safety Instructions............................................................................................................................................... vii
Safety Admonishments Definitions ....................................................................................................................................................................................................................... vii
Safety and Regulatory Statements........................................................................................................................................................................................................................ vii
Déclarations de Sécurité et de Réglementation........................................................................................................................................................................................vii
1Customer Documentation Package..................................................................................................................................1
2Installation Acceptance Checklist ...................................................................................................................................2
3Installing the System ............................................................................................................................................................4
3.1 General Requirements..............................................................................................................................................................................................................................................4
3.2 Securing the Relay Rack to the Floor.........................................................................................................................................................................................................4
3.3 Mounting the System in a Relay Rack or an Equipment Rack........................................................................................................................................10
3.3.1 Mounting the Distribution Cabinet with Module Mounting Assembly(s).......................................................................................10
3.3.2 Installing a List 93, 94 Battery Tray....................................................................................................................................................................................16
3.3.3 Installing Optional 4-Post Flush Mounting Kit for Data Cabinets, P/N 559801.........................................................................27
3.4 Changing Orientation of Load Return Busbars Located in a List 20, 21, 25, or 26 Distribution Cabinet...................................31
3.5 Installing Optional Lug Adapter Busbar Kits ....................................................................................................................................................................................33
3.6 Installing Circuit Breakers, Fuses, and Optional Transient Voltage Surge Suppressor (TVSS) Device(s) ........................... 34
3.7 Vertiv™ NetSure™ SPD (Surge Protection Device) Field Installation Kit P/N 60051981 and P/N 60056702
Installation Instructions ....................................................................................................................................................................................................................................... 42
3.7.1 Kit Description....................................................................................................................................................................................................................................... 42
3.7.2 Kit Contents............................................................................................................................................................................................................................................. 42
3.7.3 Tools and Material Required....................................................................................................................................................................................................44
3.7.4 Installation Procedure ....................................................................................................................................................................................................................44
4Setting Jumper and Switch Options............................................................................................................................ 57
4.1 Circuit Cards with Jumpers and Switches in a List 20, 21, 25, 26, 27 Distribution Cabinet...................................................................57
4.2 Jumper Settings on the System Interface Circuit Card........................................................................................................................................................60
4.3 Switch Settings on the IB2 (Controller Interface Board).......................................................................................................................................................61
4.4 Switch Settings on Optional EIB (Controller Extended Interface Board)..............................................................................................................62
4.5 Switch Settings on the SM-DU (List 60 Hybrid Connection Cabinet) ................................................................................................................... 63
4.5.1 Procedure ..................................................................................................................................................................................................................................................63
5Making Electrical Connections ...................................................................................................................................... 67
5.1 Important Safety Instructions.........................................................................................................................................................................................................................67
5.2 Wiring Considerations............................................................................................................................................................................................................................................67
5.3 Relay Rack / Equipment Cabinet Frame Grounding Connection ................................................................................................................................68
5.4 Power System Shelf Frame Grounding Requirements...........................................................................................................................................................69
5.5 Assemblies Comprising the Power System Frame Grounding Connection....................................................................................................... 70
5.6 Central Office Ground Connection........................................................................................................................................................................................................... 70
5.7 Rectifier Nominal 120 VAC / 208 VAC / 240 VAC Input and AC Input Equipment Grounding Connections......................71
5.7.1 Wiring Considerations......................................................................................................................................................................................................................71
5.7.2 To 19” or 23” Rectifier AC Input / Solar Converter DC Input Panel (List 40, 45) and 23” Rectifier AC
Input Panel (List 46)..........................................................................................................................................................................................................................71
5.7.3 To Individual Module Mounting Assembly(s) Equipped with Molex Connectors and Provided with
Rectifier AC Input Cable Assemblies or Rectifier AC Input Line Cords ...........................................................................................77

Vertiv™ NetSure™ 5100 Series -48 VDC Power System Installation Manual
Proprietary and Confidential © 2023 Vertiv Group Corp.
iv
5.8 Solar Converter 140 VDC to 200 VDC / 200 VDC to 400 VDC Input Connections...................................................................................78
5.8.1 Wiring Considerations.....................................................................................................................................................................................................................78
5.8.2 To 19” or 23” Rectifier AC Input / Solar Converter DC Input Panel (List 40, 45).....................................................................78
5.8.3 To 23” Solar Connection Cabinet (List 61) .................................................................................................................................................................. 81
5.8.4 To Individual Module Mounting Assembly(s) Equipped with Molex Connectors and Provided with
Solar Converter DC Input Cable Assemblies ............................................................................................................................................................. 81
5.9 -48 VDC System Connections to an Optional List 60 Hybrid Connection Cabinet...................................................................................84
5.10 Nominal 120 VAC Input and Equipment Grounding Connections to List 50, 51, 52, 53, 54, 55, 56, 57 Inverter
Module Assembly.......................................................................................................................................................................................................................................................85
5.11 AC "Neutral" Reference Point (If Equipped with Optional Inverter System)...................................................................................................... 88
5.12 Nominal 120 VAC Output Connections (List 50, 51, 52, 53, 54, 55, 56, 57 Inverter Module Assembly)....................................89
5.12.1 List 50, 52, 54, 56 (bulk output)............................................................................................................................................................................................89
5.12.2 List 51, 53, 55, 57 (NEMA output) ........................................................................................................................................................................................89
5.13 External Alarm, Reference, Monitoring, and Control Connections ..............................................................................................................................92
5.13.1 External Alarm, Reference, Monitoring, and Control Connection Locations................................................................................92
5.13.2 System Interface Circuit Card Connections (if required) .............................................................................................................................95
5.13.3 RS485 Modbus Connection (if required).....................................................................................................................................................................96
5.13.4 IB2 (Controller Interface Board) Connections (if required) ........................................................................................................................96
5.13.5 Optional EIB (Controller Extended Interface Board) Connections (if required)....................................................................105
5.13.6 Circuit Breaker Alarm and Shunt Monitoring Connections to an Optional List 60 Hybrid Connection
Cabinet .........................................................................................................................................................................................................................................................111
5.13.7 Optional Customer Fuel Sensor Input............................................................................................................................................................................ 113
5.13.8 Connecting a Device or System to the NCU CAN Bus (if required)..................................................................................................114
5.14 NCU Controller Ethernet Connection (if required) ..................................................................................................................................................................114
5.15 Control Bus Connections between Controller and Module Mounting Assemblies.................................................................................... 117
5.16 Optional Transient Voltage Surge Suppressor (TVSS) Device Ground Connection...............................................................................118
5.17 Load Connections ................................................................................................................................................................................................................................................... 121
5.17.1 Load Connections to a List 20, 25 Distribution Cabinet...............................................................................................................................121
5.17.2 Load Connections to a List 21, 26 Distribution Cabinet ...............................................................................................................................126
5.17.3 Load Connections to a List 27 Distribution Cabinet.........................................................................................................................................137
5.17.4 Load Connections to an Optional GMT Fuse Block.........................................................................................................................................140
5.17.5 Load Connections to a List KG Distribution Panel ............................................................................................................................................141
5.18 Connections to an Optional List 60 Hybrid Connection Cabinet..............................................................................................................................142
5.19 Input Battery Connections .............................................................................................................................................................................................................................143
5.19.1 Input Battery Connections to List 20, 25 Distribution Cabinet..............................................................................................................143
5.19.2 Input Battery Connections to List 21, 26 Distribution Cabinet...............................................................................................................146
5.19.3 Input Battery Connections to List 27 Distribution Cabinet .......................................................................................................................150
5.20 Remote Distribution Unit (DU) Connections ................................................................................................................................................................................150
5.20.1 List 27 Distribution Cabinet ....................................................................................................................................................................................................150
5.21 Installing and Connecting Batteries in an Optional List 93 or 94 Battery Tray (if furnished)......................................................... 152
5.22 Important Safety Instructions...................................................................................................................................................................................................................... 152
6Installing the Modules..................................................................................................................................................... 154
6.1Installing Rectifier, Solar Converter, and Converter Modules........................................................................................................................................154
6.2 Installing Inverter Module in Inverter Module Mounting Assembly (If Equipped with Optional Inverter System)......159
7Initially Starting, Configuring, and Checking System Operation.................................................................... 160

Vertiv™ NetSure™ 5100 Series -48 VDC Power System Installation Manual
Proprietary and Confidential © 2023 Vertiv Group Corp.
v
7.1 Important Safety Instructions......................................................................................................................................................................................................................160
7.2 Initial Startup Preparation...............................................................................................................................................................................................................................160
7.3 Initially Starting the System ..........................................................................................................................................................................................................................160
7.4 NCU Controller Initialization ..........................................................................................................................................................................................................................161
7.5 Verifying and Setting the NCU Controller as Required for Your Application.................................................................................................162
7.6 Checking System Status..................................................................................................................................................................................................................................166
7.7 Final Steps .....................................................................................................................................................................................................................................................................167

Vertiv™ NetSure™ 5100 Series -48 VDC Power System Installation Manual
Proprietary and Confidential © 2023 Vertiv Group Corp.
vi
Admonishments Used in this Document
DANGER
! Warns of a hazard the reader will be exposed to that will likely result
in death or serious injury if not avoided. (ANSI, OSHA)
WARNING
! Warns of a potential hazard the reader may be exposed to that could
result in
death or serious injury if not avoided. This admonition is not used for situations that pose a
risk only to equipment, software, data, or service. (ANSI)
CAUTION
! Warns of a potential hazard the reader may be exposed to that could
result in minor or moderate injury if not avoided. (ANSI, OSHA) This admonition is not
used for situations that pose a risk only to equipment, data, or service, even if such use
appears to
be permitted in some of the applicable standards. (OSHA)
ALERT
! Alerts the reader to an action that must be avoided in order to protect
equipment, software, data, or service. (ISO)
ALERT
! Alerts the reader to an action that must be performed in order to prevent
equipment damage, software corruption, data loss, or service interruption. (ISO)
FIRE SAFETY
! Informs the reader of fire safety information, reminders, precautions,
or policies, or of the locations of fire
-fighting and fire-safety equipment. (ISO)
SAFETY
! Informs the reader of general safety information, reminders, precautions, or
policies not
related to a particular source of hazard or to fire safety. (ISO, ANSI, OSHA)

Vertiv™ NetSure™ 5100 Series -48 VDC Power System Installation Manual
Proprietary and Confidential © 2023 Vertiv Group Corp.
vii
Important Safety Instructions
Safety Admonishments Definitions
Definitions of the safety admonishments used in this document are listed under “Admonishments Used in this Document” on page vi.
Safety and Regulatory Statements
Refer to Section 4154 (provided with your customer documentation) for Safety and Regulatory Statements.
Déclarations de Sécurité et de Réglementation
Reportez-vous à la Section 4154 (fourni avec les documents de votre client) pour les déclarations de sécurité et de réglementation.

Vertiv™ NetSure™ 5100 Series -48 VDC Power System Installation Manual
Proprietary and Confidential © 2023 Vertiv Group Corp.
viii
This page intentionally left blank.

Vertiv™ NetSure™ 5100 Series -48 VDC Power System Installation Manual
Proprietary and Confidential © 2023 Vertiv Group Corp.
1
1Customer Documentation Package
This document (IM582137100) provides Installation Instructions for Vertiv™ NetSure™ -48 VDC Power System Model 5100, Spec. No.
582137100.
The complete Customer Documentation Package consists of…
-48 VDC Power System Installation Manual
•Power System Installation Instructions: IM582137100
NCU Controller User Manual
•NCU Controller User Instructions: UM1M830BNA
USB Drive with All Customer Documentation
•Power System Installation Instructions: IM582137100
•Power System User Instructions: UM582137100
•Power System “System Application Guide”: SAG582137100
•Module Mounting Assembly Power Data Sheet: PD588705300
•NCU Controller User Instructions: UM1M830BNA
•Rectifier Instructions: UM1R482000E3
•Solar Converter Instructions: UM1S482000E3
•-48 VDC to +24 VDC Converter Instructions: UM1C48241500
•-48 VDC to -58 VDC Converter Instructions: UM1C48582000P3
•Inverter Instructions: UM1I1201000
•Engineering Drawings
•Also provided on the USB drive is a controller configuration drawing and the controller configuration files loaded into the
controller as shipped.

Vertiv™ NetSure™ 5100 Series -48 VDC Power System Installation Manual
Proprietary and Confidential © 2023 Vertiv Group Corp.
2
2Installation Acceptance Checklist
Provided in this section is an Installation Acceptance Checklist. This checklist helps ensure proper installation and initial operation of
the system. As the procedures presented in this document are completed, check the appropriate box on this list. If the procedure is
not required to be performed for your installation site, also check the box in this list to indicate that the procedure was read. When
installation is done, ensure that each block in this list has been checked. Some of these procedures may have been factory performed
for you.
NOTE! The system is not powered up until the end of this checklist.
NOTE! Some of these procedures may have been performed at the factory for you.
Installing the System
Relay Rack Secured to Floor (if required)
Distribution Cabinet with Module Mounting Assembly(s) Secured to Relay Rack or Equipment Rack
Optional Battery Tray Installed
Optional Battery Tray Battery Disconnect Circuit Breaker Installed
Optional P/N 559801 4-Post Flush Mounting Kit for Data Cabinets Installed (if required)
Optional P/N 560075 Field Expansion Module Mounting Assembly Spacer Kit Installed (if required)
Optional P/N 559802 Flush Mounting Kit for Relay Rack, NEBS Zone 2 Installed (if required)
Load Return Busbar Orientation Changed (if required)
Optional Lug Adapter Busbar Kits Installed
Circuit Breakers and/or Fuses Installed
Optional Transient Voltage Surge Suppressor (TVSS) Device(s) Installed
Setting Jumper and Switch Options
Jumper on System Interface Circuit Card Set
Factory Switch Setting on IB2 (Controller Interface Board) Verified
Factory Switch Setting on Optional EIB (Controller Extended Interface Board) Verified
Factory Switch Settings on SM-DU Circuit Card (located in Optional List 60 Hybrid Connection Cabinet) Verified
Making Electrical Connections
Relay Rack / Cabinet Frame Grounding Connection Made
Assemblies Comprising the Power System Frame Grounding Connection Made
Central Office Ground Connection Made
Rectifier AC Input and AC Input Equipment Grounding Connections Made
Solar Converter DC Input Connections Made (if required)

Vertiv™ NetSure™ 5100 Series -48 VDC Power System Installation Manual
Proprietary and Confidential © 2023 Vertiv Group Corp.
3
AC Output Connections Made (if equipped with Optional Inverter System)
External Alarm, Reference, Monitoring, and Control Connections to System Interface Circuit Card Made
External Alarm, Reference, Monitoring, and Control Connections to IB2 (Controller Interface Board) Made
External Alarm, Reference, Monitoring, and Control Connections to Optional EIB (Controller Extended Interface Board) Made
Fuel Sensor Connection Made (if required)
Circuit Breaker Alarm and Shunt Monitoring Connections to SM-DU Circuit Card (located in Optional List 60 Hybrid
Connection Cabinet) Made
External Device (such as SM-Temp Module) Connection to NCU Controller CAN Bus Made (if required)
NCU Controller Ethernet Port Connection Made
NCU Controller Second Ethernet Port Connection Made (if required)
Factory NCU Control Bus Connections between NCU Controller and Module Mounting Assembly(s) Verified
Optional Transient Voltage Surge Suppressor (TVSS) Device(s) Ground Connection Made
Load Connections to Distribution Cabinet Made
Load Connections to GMT Fuse Block Made (if required)
Connections to Optional List 60 Hybrid Connection Cabinet Made
External Battery Connections Made
Internal Batteries Installed and Connected in an Optional Battery Tray
Installing the Modules
Rectifier, Solar Converter, Converter Modules, and Inverter Modules (if equipped with Optional Inverter System) Installed
Initially Starting the System
System Started, Configured, and Checked

Vertiv™ NetSure™ 5100 Series -48 VDC Power System Installation Manual
Proprietary and Confidential © 2023 Vertiv Group Corp.
4
3Installing the System
3.1 General Requirements
•This product is intended only for installation in a restricted access location on or above a non-combustible surface.
•This product must be located in a controlled environment with access to crafts persons only.
•This product is intended for installation in network telecommunication facilities (CO, vault, hut, or other environmentally
controlled electronic equipment enclosure).
•This product is intended for connection to the common bonding network in a network telecommunication facility (CO, vault,
hut, or other environmentally controlled electronic equipment enclosure).
•The DC return connection to this system can remain isolated from system frame and chassis (DC-I).
•This system is suitable for installation as part of the Common Bonding Network (CBN).
•The installer should be familiar with the installation requirements and techniques to be used in securing the relay rack to the
floor.
•The installer should be familiar with the installation requirements and techniques to be used in securing the distribution
cabinet with module mounting assembly(s) to a relay rack or equipment rack.
•Rectifier, solar converter, converter, inverter (if equipped with optional inverter system) and module mounting assembly(s)
ventilating openings must not be blocked and temperature of air entering rectifiers, solar converters, converters, and
inverters must not exceed rated operating ambient temperature range found in SAG582137100.
•Clearance requirements are:
a) Recommended minimum aisle space clearance for the front of each bay is 2' 6".
b) Recommended minimum aisle space clearance for the rear of each bay is 2’ 0” for any of the following conditions:
1. Addition of a module mounting assembly in the field.
2. Making input connections to a field installed module mounting assembly.
3. Adding battery tray(s) in the field.
For all other conditions, required minimum spacing from the rear of the system to a wall or other solid structure must not be
less than four (4) inches and from the front of the system not less than two (2) inches. This will assure proper airflow
through the rectifier, solar converter, and converter modules.
NOTE! Minimum spacing specified for ventilation may not permit replacement of certain components such as busbars or
module mounting assemblies.
•Front door and top / rear covers must be removed in cabinet applications above +40 °C (+104 °F). See SAG582137100 for
temperature ratings.
3.2 Securing the Relay Rack to the Floor
All equipment ordered is factory mounted to the relay rack or shipping rails specified when ordered.
Secure the relay rack to the floor per site requirements. Refer to “General Requirements” on page 4.
Ventilation Requirements
Refer to “General Requirements” on page 4.

Vertiv™ NetSure™ 5100 Series -48 VDC Power System Installation Manual
Proprietary and Confidential © 2023 Vertiv Group Corp.
5
Relay Rack Floor Mounting Dimensions
Refer to Figure 3.1 and Figure 3.2 for relay rack floor mounting dimensions.
Optional Relay Rack Isolation Kit
Refer to Figure 3.3 when using the Optional Relay Rack Isolation Kit.
Figure 3.1 Relay Rack Floor Mounting Dimensions - 23” (cont’d on next page)
Part No. 543156
Part No. 543160
Part No. 543161, 543162,
543163, 543164
17.50
20.13
24.38
2.13
3.44
9.88
12.53
15.00
1.24
2.56
0.875 Dia.
(8 Places)
Masked for Frame Ground Lug
0.281 Dia. Holes on 0.625 Centers
(Top of Rack, 2 Places)
22.500
24.750
1.125
15.000
17.500
20.125
25.000
2.437
3.750
9.871
12.531
15.031
1.250
2.580
2.00
1.00
1.00
2.00
2.00
2.00
5.00
0.437 Dia.
(12 Places)
Masked for Frame Ground Lug
0.281 Dia. Holes on 0.625 Centers
(Top of Rack, 2 Places)
0.875 Dia.
(8 Places)
Masked for Frame Ground Lug
0.281 Dia. Holes on 0.625 Centers
(Top of Rack, 1 Place)
Part No. 541340
19.685
22.310
25.800
1.760
3.073
12.34
15.000
18.000
1.500
2.830
0.875 Dia.
(8 Places)
Masked for Frame Ground Lug
0.281 Dia. Holes on 0.625 Centers
(Top of Rack, 2 Places)

Vertiv™ NetSure™ 5100 Series -48 VDC Power System Installation Manual
Proprietary and Confidential © 2023 Vertiv Group Corp.
6
Figure 3.1 Relay Rack Floor Mounting Dimensions - 23” (cont’d from previous page, cont’d on next page)
19.685
25.80
15.000
1.50
2.83
18.00
0.875
8 Places
Part No.
562353 12.340
22.310
3.06
1.74

Vertiv™ NetSure™ 5100 Series -48 VDC Power System Installation Manual
Proprietary and Confidential © 2023 Vertiv Group Corp.
7
Figure 3.1 Relay Rack Floor Mounting Dimensions - 23” (cont’d from previous page)
Part No.
559819
24.75
1.25
1.25
9.87 12.53
20.13
17.50
3.63
2.31
15.03
0.88
8 Places
22.31 1.73
3.04
19.69
18.00
25.80
2.83
1.50
15.00 12.34
0.875
8 Places
Masked for Frame Ground Lug
0. 281 Dia.Holes on 0.625 Centers
(Top of Rack, 2 Places)
Part No. 10009902

Vertiv™ NetSure™ 5100 Series -48 VDC Power System Installation Manual
Proprietary and Confidential © 2023 Vertiv Group Corp.
8
Figure 3.2 Relay Rack Floor Mounting Dimensions - 19”
Part No. 559823
PartNo.559824
13.50
16.13
20.38
2.13
3.44
9.88
12.53
15.00
1.24
2.56
0.875Dia.
(8 Places)
Masked for Frame Ground Lug
0.281 Dia. Holes on 0.625 Centers
(Top ofRack,2 Places)
Masked for Frame Ground Lug
0.281 Dia. Holes on 0.625 Centers
(Top of Rack, 2 Places)
14.13
16.75
21.00
2.13
3.44
9.38
12.03
15.00
1.49
2.81
0.875 Dia.
(8 Places)
Notes:
1. All dimensions are in inches.
Part No. 563922
Masked for Frame Ground Lug
0.334 Dia. Holes on 0.625 Centers
(Topof Rack, 2 Places)
15.69
18.31
21.80
1.76
3.07
12.34
15.00
18.00
1.50
2.83
0.812 Dia.
(8 Places)

Vertiv™ NetSure™ 5100 Series -48 VDC Power System Installation Manual
Proprietary and Confidential © 2023 Vertiv Group Corp.
9
Figure 3.3 Optional Relay Rack Isolation Kit Mounting
Isolation Pad
Floor
Floor Anchors
(Customer Provided)
Typical 23” Relay Rack
1/2-inch
Flat Washer
(4-places)
1/2-inch
Bushing
(4-places)
Isolation Pad
Floor
Floor Anchors
(Customer Provided)
1/2-inch
Flat Washer
(4-places)
1/2-inch
Bushing
(4-places)
Typical 19” Relay Rack

Vertiv™ NetSure™ 5100 Series -48 VDC Power System Installation Manual
Proprietary and Confidential © 2023 Vertiv Group Corp.
10
3.3 Mounting the System in a Relay Rack or an Equipment Rack
NOTE! If the power system was ordered in a relay rack, these procedures have been performed at the factory.
This power system is designed to mount in a standard 19” or 23” (depending on configuration ordered) relay rack or equipment rack
having 1” or 1-3/4” multiple drillings. Refer to System Application Guide SAG582137100 for overall dimensions and a list of available
relay racks.
NOTE! Refer to “General Requirements” on page 4 for mounting restrictions and ventilation requirements.
NOTE! A 4-post mounting kit for a data cabinet is available. See SAG582137100.
NOTE! A special mounting bracket kit (P/N 564300) is available. See SAG582137100. Mounting instructions using this kit is
provided in this section.
NOTE! A 19” to 23” wide relay rack mounting bracket kit (P/N 553630) is available. See SAG582137100. Mounting
instructions using this kit is provided in this section.
3.3.1 Mounting the Distribution Cabinet with Module Mounting Assembly(s)
NOTE! The distribution cabinet is factory connected to the module mounting assembly(s). The distribution cabinet with
module mounting assembly(s) is mounted as a complete assembly.
The distribution cabinet with module mounting assembly(s) must be the top-most component in the rack. Perform the following
steps to mount the distribution cabinet with module mounting assembly(s).
DANGER! If the system is mounted in a relay rack, the relay rack must be securely anchored to the floor before the
distribution cabinet with module mounting assembly(s) is installed.
DANGER! The distribution cabinet with module mounting assembly(s) is heavy. Use a hoist, battery lift, or other appropriate
lifting device to raise and support the assembly during the installation. Take appropriate precautions to avoid injury.
Procedure
1. Remove the distribution cabinet with module mounting assembly(s) from its shipping rails. Position the assembly in the relay
rack or equipment rack.
NOTE! In the next steps, install (orient) the ground washers so the teeth dig into the mounting angles for a secure ground
connection.
2. Mount the distribution cabinet to the rack using hardware as shown in Figure 3.4 or Figure 3.5. Refer to Figure 3.4 or
Figure 3.5 for recommended torque.
3. Mount the module mounting assembly(s) to the rack using hardware as shown in Figure 3.4 or Figure 3.5.Refer to Figure 3.4
or Figure 3.5 for recommended torque.

Vertiv™ NetSure™ 5100 Series -48 VDC Power System Installation Manual
Proprietary and Confidential © 2023 Vertiv Group Corp.
11
Figure 3.4 Mounting a System with a 1-Row Distribution Cabinet (List 20, 25, 27)
Figure 3.5 Mounting a System with a 2-Row Distribution Cabinet (List 21, 26)

Vertiv™ NetSure™ 5100 Series -48 VDC Power System Installation Manual
Proprietary and Confidential © 2023 Vertiv Group Corp.
12
Mounting the Distribution Cabinet with Module Mounting Assembly Using Special Mounting Bracket Kit
P/N 564300
The special mounting bracket kit P/N 564300 is used to mount a system configuration consisting of a single row distribution panel
and a single module mounting assembly in a 1" center to center mounting hole relay rack with a maximum of 7-3/4" from the front side
of the rack to the back of the system.
NOTE! The distribution cabinet is factory connected to the module mounting assembly. The distribution cabinet with
module mounting assembly is mounted as a complete assembly.
Perform the following steps to mount the distribution cabinet with module mounting assembly.
DANGER! If the system is mounted in a relay rack, the relay rack must be securely anchored to the floor before the
distribution cabinet with module mounting assembly is installed.
DANGER! The distribution cabinet with module mounting assembly is heavy. Use a hoist, battery lift, or other appropriate
lifting device to raise and support the assembly during the installation. Take appropriate precautions to avoid injury.
Procedure
NOTE! In the next step, install (orient) the kit supplied ground washers so the teeth dig into the special mounting brackets
for a secure ground connection.
1. Refer to Figure 3.6 and attach the left and right kit supplied special mounting brackets to the rack. Refer to Figure 3.6 to
identify the left and right special mounting brackets and to orient the brackets correctly. Refer to Figure 3.6 for
recommended torque.
2. Remove the distribution cabinet with module mounting assembly from its shipping rails or box. Mount the assembly onto the
special mounting brackets attached to the rack in the previous step.
NOTE! In the next step, install (orient) the ground washers so the teeth dig into the mounting angles for a secure ground
connection.
3. Mount the distribution cabinet with module mounting assembly to the rack using hardware as shown in Figure 3.4.Refer to
Figure 3.4 for recommended torque.