Vertiv Liebert EXL User manual

Liebert®EXL™Uninterruptible Power System
Operation and Maintenance Manual—625-1200kVA, 60Hz, Three-Phase, Single &
Multi-Module

Vertiv™|Liebert® EXL™ 625-1100kVA Operation and Maintenance Manual | Rev. 8 | 02/17 i
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
SAVE THESE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
BATTERY CABINET PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.0 INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
1.2.1 Normal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
1.2.2 Bypass Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
1.2.3 Battery Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
1.2.4 Eco Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.2.5 Maintenance Bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.3 Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.0 LCD TOUCHSCREEN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2.2 Touchscreen Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.2.1 Main Display Screen (Home) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.2.2 Configuration Menu Rating (Config) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.2.3 Reports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
2.2.4 Metering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.2.5 Operation Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
2.2.6 Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
2.2.7 Silence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
2.2.8 System View—1+N Systems Only. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
2.2.9 Remote Breaker Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
3.0 OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
3.1 Manual Operations—Single-Module Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
3.1.1 Startup—Single Module System with Internal Breakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
3.1.2 Startup for a Single-Module System with Remote Breakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.1.3 Load Transfer and Retransfer—Single Module System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.1.4 Maintenance Bypass Load Transfers-Single Module System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.1.5 Maintenance Bypass Load Transfers—Single Module System: If Load is on Maintenance Bypass. . . . 24
3.1.6 Conditions to Activate Eco Mode Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.1.7 Conditions to Suspend Eco Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.1.8 Conditions to Terminate Eco Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.1.9 Bypass Source Qualification for Eco Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.1.10 Critical Bus Disqualification for Eco Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.1.11 Settings for Eco Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.1.12 Enabling Eco Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.1.13 Eco Mode—Scheduled Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.1.14 Eco Mode—Manual Start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.1.15 Exiting Eco Mode Manually. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.1.16 Shutdown—Single Module UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Vertiv™|Liebert® EXL™ 625-1100kVA Operation and Maintenance Manual | Rev. 8 | 02/17 ii
3.2 Manual Operations—1+N Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.2.1 Startup—1+N Module System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.2.2 Load Transfer-1+N System: Remove a UPS from System (Collective) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
3.2.3 Load Transfer-1+N System: Add a UPS to the System (Collective) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.2.4 Load Transfer-1+N System: Transfer System to Bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.2.5 Load Transfer-1+N System: Transfer System to Inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.2.6 Maintenance Bypass Load Transfers-1+N Module System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.2.7 Shutdown—1+N UPS: UPS Module Inverter Shutoff . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.2.8 Shutdown—1+N UPS: UPS Module System Shutdown (Remove UPS Module from the Collective) . . . 35
3.2.9 Shutdown—1+N System Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.2.10 Startup for 1+N System with Remote Breakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3.3 Shutdown for Systems with Remote Breakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
3.4 Automatic Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
3.4.1 Overloads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.4.2 Automatic Transfers to Bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.4.3 Automatic Transfers to Bypass, UPS Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.4.4 Automatic Retransfers to UPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4.0 OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.1 Input Contact Isolator Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.2 Programmable Relay Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
4.2.1 Configuring the Programmable Relay Board Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.3 Remote Alarm Status Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.3.1 Lamp Test/Reset Push Button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.3.2 Audio Reset Push Button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.4 Digital Load Bus Sync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.4.1 System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.4.2 LBS Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.4.3 Normal Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.4.4 Slave Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.4.5 Master System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4.4.6 Slave System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
5.0 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
5.1 Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
5.2 Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
5.2.1 Record Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
5.2.2 Air Filters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
5.2.3 Limited Life Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
5.3 Battery Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
5.3.1 Battery Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
5.3.2 Torque Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
5.4 Detecting Trouble. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
5.5 Reporting a Problem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
5.6 Upstream Feeder Circuit Breaker Setting Inspections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
6.0 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.1 Battery Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Vertiv™|Liebert® EXL™ 625-1100kVA Operation and Maintenance Manual | Rev. 8 | 02/17 iii
6.2 Other DC Sources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.3 Environmental Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
7.0 DISCLOSURES WITH REGARD TO EMBEDDED SOFTWARE LICENSED FROM
NOKIA, INC., (“SUBLICENSED SOFTWARE”) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Appendix A - Inverter Overload Curve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A59
Appendix B - UPS Alarm and Status Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A60
FIGURES
Figure 1 Typical single module UPS one-line diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Figure 2 Main component locations—625kVA, 750kVA and 800kVA (typical) . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Figure 3 Main components for remote breaker configuration—Single module with static bypass or 1+N
multi-module; 625kVA-800kVA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 4 Main component locations—1000kVA, 1100kVA, and 1200kVA (typical) . . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 5 Main components for remote breaker configuration—Single module with static bypass or 1+N
multi-module; 1000kVA-1200kVA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Figure 6 Main display screen, typical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Figure 7 Configuration menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 8 System Meter menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Figure 9 Battery Meter menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Figure 10 UPS Operation menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Figure 11 Status View—1+N systems only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Figure 12 Main display screen—Remote breaker configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Figure 13 Input Contact Isolator dialog box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Figure 14 Optional Input Contact Isolator Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Figure 15 Control wiring, Programmable Relay Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Figure 16 Programmable Relay Board menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Figure 17 Liebert EXL inverter overload curve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
TABLES
Table 1 Input Contact Isolator Board pre-assigned values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Table 2 Input Contact Isolator Board control wiring connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Table 3 Programmable Relay Board pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Table 4 RAS indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Table 5 UPS component service life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Table 6 Environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Table 7 Electrical specifications and standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Table 8 Physical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Table 9 UPS Alarm and Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Vertiv™|Liebert® EXL™ 625-1100kVA Operation and Maintenance Manual | Rev. 8 | 02/17 iv

Vertiv™|Liebert® EXL™ 625-1100kVA Operation and Maintenance Manual | Rev. 8 | 02/17 1
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This manual contains important instructions that should be followed during installation and maintenance of the
Liebert EXL uninterruptible power system and DC source.
!
WARNING
Risk of electric shock. Can cause equipment damage, injury or death.
Exercise extreme care when handling UPS cabinets to avoid equipment damage or injury to personnel.
Refer to separate installation manual for equipment handling information and installation procedures.
Follow all DC source safety precautions in 5.0 - Maintenance when installing, charging or servicing DC
sources. In addition to the hazard of electric shock, gas produced by batteries can be explosive and
sulfuric acid can cause severe burns.
In case of fire involving electrical equipment, use only carbon dioxide fire extinguishers or others
approved for use in electrical fire fighting.
Extreme caution is required when performing maintenance. Service and maintenance work must be
performed only by properly trained and qualified personnel and in accordance with applicable regulations
as well as with manufacturers’ specifications.
Be constantly aware that the UPS contains high DC as well as AC voltages. With input power off and the
DC source disconnected, high voltage at filter capacitors and power circuits should be discharged within
5 minutes. However, if a power circuit failure has occurred, assume that high voltage still exists after
shutdown. Check with a voltmeter before making contact.
AC voltage will remain on the system bypass, the UPS output terminals and the static bypass switch,
unless associated external circuit breakers are opened.
Check for voltage with both AC and DC voltmeters prior to making contact.
When the UPS is under power, both the operator and any test equipment must be isolated from direct
contact with earth ground and the UPS chassis frame by using rubber mats.
Some components within the cabinets are not connected to the chassis ground. Any contact between
floating circuits and the chassis is a lethal shock hazard. Exercise caution that the test instrument exterior
does not make contact, either physically or electrically, with earth ground.

Vertiv™|Liebert® EXL™ 625-1100kVA Operation and Maintenance Manual | Rev. 8 | 02/17 2
This equipment contains circuitry that is energized with high voltage. Only test equipment designated for
troubleshooting should be used. This is particularly true for oscilloscopes. Always check with an AC and DC
voltmeter to ensure safety before making contact or using tools. Even when the power is turned Off, dangerously
high voltage may exist at the capacitor banks.
Observe all DC source precautions when near the DC source for any reason.
ONLY properly trained and qualified service personnel should perform maintenance on the UPS system. When
performing maintenance on any part of the equipment under power, service personnel and test equipment
should be standing on rubber mats. The service personnel should wear insulating shoes for isolation from direct
contact with the floor (earth ground).
One person should never work alone. A second person should be standing by to assist and summon help in case
an accident should occur. This is particularly true when work is performed on the DC source.
!
AVERTISSEMENT
Risque de décharge électrique pouvant entraîner des dommages matériels, des blessures et même la
mort.
Faites preuve d’une extrême prudence lors de la manutention des armoires ASC afin d’éviter de les
endommager ou de blesser le personnel. Reportez-vous au manuel d’installation approprié pour connaître
les consignes de manutention et les procédures d’installation de l’équipement. Observez toutes les
mesures de sécurité relatives à la source d’alimentation c.c. décrites dans la section 4.0 - Entretien lors de
l'installation, de la charge ou de l’entretien des sources c.c. Outre les risques de décharge électrique
associés aux batteries, les gaz qu’elles produisent peuvent être explosifs et l’acide sulfurique qu’elles
contiennent peut provoquer des brûlures graves.
En cas d’incendie associé à du matériel électrique, n’utilisez que des extincteurs à dioxyde de carbone ou
homologués pour la lutte contre les incendies d’origine électrique.
Les opérations d’entretien requièrent une extrême prudence. Les opérations d’entretien ne doivent être
confiées qu’à du personnel qualifié et dûment formé. Toutes les interventions doivent être effectuées
conformément aux règlements applicables et aux spécifications du fabricant. Soyez toujours conscient
du fait que le système ASC contient des tensions c.c. et c.a. élevées.
Une fois l’alimentation d’entrée coupée et la source d’alimentation c.c. débranchée, la haute tension aux
condensateurs de filtrage et aux circuits d’alimentation devrait se dissiper en moins de 5 minutes. En cas
de défaillance d’un circuit d’alimentation, toutefois, il importe de présumer qu’une tension élevée est
présente même après l’arrêt. Vérifiez toujours les tensions avec un voltmètre avant d’établir des contacts.
Le circuit de dérivation, les bornes de sortie ASC et le commutateur statique de derivation continueront
d’afficher une tension c.a. à moins que les disjoncteurs externes associés ne soient ouverts.
Vérifiez les tensions avec des voltmètres c.a. et c.c. avant d’établir tout contact.
Lorsque le système ASC est sous tension, les responsables de l’entretien et l’équipement d’essai doivent
reposer sur des tapis de caoutchouc pour prévenir tout contact direct avec le sol et avec le châssis du
système lors des interventions.
Certains composants à l’intérieur des armoires ne sont pas connectés à la masse du châssis. Tout contact
entre les circuits flottants et le châssis présente un risque de décharge mortelle. Il importe de veiller à ce
que l’extérieur des équipements d’essai n’entre pas en contact physique ou électrique avec le sol.

Vertiv™|Liebert® EXL™ 625-1100kVA Operation and Maintenance Manual | Rev. 8 | 02/17 3
BATTERY CABINET PRECAUTIONS
The following warning applies to all battery cabinets supplied with UPS systems. Additional warnings and
cautions applicable to battery cabinets may be found in Important Safety Instructions on page 1 and 5.3 -
Battery Maintenance.
Contacting Vertiv® for Support
Contact Vertiv Services for information or repair service in the United States at 1-800-2378.
For repair or maintenance service outside the 48 contiguous United States, contact Vertiv Services, if available in
your area. For areas not covered by Vertiv Services, the authorized distributor is responsible for providing
qualified, factory-authorized service.
Have the following information available before calling Vertiv Services:
Part Numbers: ________________________________________________________________________________________________________
Serial Numbers: ______________________________________________________________________________________________________
kVA Rating: __________________________________________________________________________________________________________
Date Purchased: _____________________________________________________________________________________________________
Date Installed: ________________________________________________________________________________________________________
Location: _____________________________________________________________________________________________________________
Input Voltage/Frequency: ____________________________________________________________________________________________
Output Voltage/Frequency: __________________________________________________________________________________________
DC Source Reserve Time: ____________________________________________________________________________________________
!
WARNING
Internal battery strapping must be verified by manufacturer prior to moving a battery cabinet (after initial
installation).
• Battery cabinets contain non-spillable batteries.
• Keep units upright.
•Donotstack.
• Do not tilt.
Failure to heed this warning could result in smoke, fire or electric hazard.
Call 1-800-543-2378 before moving battery cabinets (after initial installation).
For systems using DC sources other than batteries, refer to the manufacturer’s recommendations for
handling and care.
!
AVERTISSEMENT
L’arrimage des batteries internes doit être vérifié par le fabricant avant de déplacer une armoire de
batteries (après l’installation initiale).
• Les armoires de batteries contiennent des batteries étanches.
• Maintenir les systèmes à la verticale.
• Ne pas empiler.
• Ne pas incliner.
• Le non-respect de ces consignes comporte des risques liés à la fumée, au feu ou à l’électricité.
• Composez le 1 800 543-2378 avant de déplacer des armoires de batteries (après l’installation initiale).
Reportez-vous aux recommandations du fabricant relatives à la manipulation et à l’entretien pour les
systèmes qui utilisent d’autres sources d’alimentation c.c. que les batteries

Vertiv™|Liebert® EXL™ 625-1100kVA Operation and Maintenance Manual | Rev. 8 | 02/17 4
1.0 INTRODUCTION
1.1 GENERAL DESCRIPTION
The Liebert EXL provides continuous, high-quality AC power to business-critical equipment, such as
telecommunications and data processing equipment. The Liebert EXL supplies power that is free of the
disturbances and variations in voltage and frequency common to utility power, which is subject to brownouts,
blackouts, surges and sags.
The Liebert EXL utilizes the latest in high-frequency, double-conversion pulse-width modulation technology and
fully digital controls to enhance its reliability and increase the ease of use.
As shown in Figure 1, the AC utility source is input at the rectifier and the rectifier converts the AC utility into DC
power. The inverter converts that DC power from the rectifier or DC power from the DC source- into AC power
for the load. The DC source will power the load through the inverter in the event of a power failure. The utility
source can also power the load through the static bypass.
If maintenance or repair of the UPS is necessary, the load can be switched without interruption in service to the
optional maintenance bypass.
Figure 1 Typical single module UPS one-line diagram
Bypass
AC Input
Rectifier
AC Input
To DC Supply
AC
Output
CB2
BFB
CB1
(E)
* The remote breaker option will have
different acronyms than shown in
the figure for the bypass and rectifier
UPS breakers:
RBB = Remote Backfeed Breaker
RIB = Rectifier Input Breaker

Vertiv™|Liebert® EXL™ 625-1100kVA Operation and Maintenance Manual | Rev. 8 | 02/17 5
Figure 2 Main component locations—625kVA, 750kVA and 800kVA (typical)
CORE OUTPUT/BYPASS CORE
U46-8C-2000
Rev. 5
DOORS AND INNER SKINS NOT SHOWN
Options Box
(5 Slots)
Liebert
IntelliSlot
Housings
Motor
Operated
Circuit
Breaker (CB1) Module Output
Circuit Breaker
(CB2)
Backfeed
Circuit Breaker
(BFB)
Input
Ground
Control
Drawer
Input
Busbars
DC
Input
Output
Busbars
Bypass
Busbars
High-Voltage
Sense Test
Points
INPUT
Output
Ground
Busbar

Vertiv™|Liebert® EXL™ 625-1100kVA Operation and Maintenance Manual | Rev. 8 | 02/17 6
Figure 3 Main components for remote breaker configuration—Single module with static bypass or 1+N multi-module;
625kVA-800kVA
Figure 4 Main component locations—1000kVA, 1100kVA, and 1200kVA (typical)
Module
Output
Circuit
Breaker
(CB2)
Bypass
Busbars
Output
Ground
Busbar
Output
Busbars
Liebert
IntelliSlot
Housings
Options Box
(5 Slots)
High-Voltage
Sense
Connectors
DC Input
Input
Busbars
Input
Ground
OUTPUT/BYPASSCORE COREINPUT
U46-8C-2002
Rev. 0
DOORS AND INNER SKINS NOT SHOWN
Back Feed
Circuit
Breaker
(BFB)
Module
Output
Circuit
Breaker
(CB2)
Bypass
Busbars
Output
Ground
Busbar
Output
Busbars
Liebert IntelliSlot
Housings
Motor Operated
Circuit Breaker
(CB1)
Options
Box (5 Slots)
High-Voltage
Sense
Test Points
DC Input
Input
Busbars
Input
Ground
Control
Drawer
OUTPUT/BYPASSCORE CORE COREINPUT
U46-12C-2000
Rev. 3
DOORS AND INNER SKINS NOT SHOWN

Vertiv™|Liebert® EXL™ 625-1100kVA Operation and Maintenance Manual | Rev. 8 | 02/17 7
Figure 5 Main components for remote breaker configuration—Single module with static bypass or 1+N multi-module;
1000kVA-1200kVA
1.2 MODES OF OPERATION
1.2.1 Normal Mode
Operating in normal mode, the Liebert EXL’s rectifier derives power from a utility AC source and supplies
regulated DC power to the inverter, which regenerates precise AC power to supply the connected equipment.
The rectifier also uses the utility source power to charge the DC sources.
1.2.2 Bypass Mode
When the Liebert EXL is in bypass mode, the load is directly supported by utility power and is without DC source
backup protection.
The Liebert EXL’s inverter and bypass static switch will shift the load from the inverter to bypass mode without
an interruption in AC power if the inverter is synchronous with the bypass and any of the following occurs:
• Inverter fails
• Inverter overload capacity is exceeded
• Inverter is manually turned Off
1.2.3 Battery Mode
When utility AC power fails, the Liebert EXL protects the critical load by instantaneously channeling DC source
power to the inverter, which continues supporting the critical load without interruption.
When utility power returns and is within acceptable limits, the Liebert EXL automatically shifts back to Normal
mode, with the rectifier powering the critical load.
NOTE
If the inverter is asynchronous with the bypass, the static switch will transfer the load from the inverter to the
bypass WITH interruption in AC power to the critical load. This interruption is 167ms when the Bypass-
Interrupted Transfer is set to Normal. The interruption is 33ms when the Bypass-Interrupted Transfer is set to
Fast. The default setting for interrupted transfer is Fast (2ms), but Vertiv Services can adjust the interrupted
transfer to Slow (10ms).
M
o
d
u
l
e
O
ut
p
ut
C
ircuit
B
reaker
(CB2)
By
pass
B
usbars
Out
p
ut
G
round
B
usbar
O
utput
B
us
b
ars
Liebert Intelli
S
lot
Housin
g
s
Op
tions Box
(
5 Slots
)
H
igh-Voltage
S
ense
C
onnectors
D
C Input
Input
B
usbars
Input
G
round
C
ontrol
D
rawer
O
UTPUT
/
BYPA
SS
CORE CORE COREINP
U
T
U46-12C-2002
R
e
v.
1
DOO
R
S
AND INNER
S
KIN
S
N
O
T
S
H
O
W
N

Vertiv™|Liebert® EXL™ 625-1100kVA Operation and Maintenance Manual | Rev. 8 | 02/17 8
1.2.4 Eco Mode
The Liebert EXL 800 and 1200 and derate single module systems have Eco Mode available for user
configuration. Eco Mode is a standard feature of the Liebert EXL system and is factory-installed. The feature
must be enabled in the field through the configuration menu on the UPS control screen as described in this
document.
The feature is also known as Active Inverter Eco Mode because the UPS inverter is On and available to receive
the load immediately. While in Eco Mode, the inverter is in zero power mode, increasing system efficiency. The
operation allows powering the critical load from the bypass source when that source is within acceptable
operating limits. If the bypass source voltage or frequency goes outside of the acceptable operation band, the
critical load is automatically transferred to the UPS inverter without interruption. The load can be transferred
from the bypass source to the inverter in a make-before-break operation.
1.2.5 Maintenance Bypass
The installation of a Maintenance Bypass Cabinet or Assembly is recommended to allow total isolation of the
UPS from all power sources while continuing to supply power to the critical load. Maintenance Bypass use is
described in 3.0 - Operation.

Vertiv™|Liebert® EXL™ 625-1100kVA Operation and Maintenance Manual | Rev. 8 | 02/17 9
1.3 OPTIONS
A number of options are available from Vertiv®for the Liebert EXL. (Some options are not available for all ratings.)
Described below are the most frequently provided options. Other options are available. Contact your Vertiv
representative for more information.
• Battery and Racks—The batteries provide power in the event of a power outage. The Liebert EXL can use a variety of
battery types, provided the battery plant is designed for the UPS DC voltage range and the load requirements of the
application.
• Battery Cabinets—Valve-regulated, lead-acid (VRLA) sealed batteries are available in matching cabinets for convenient
installation and maintenance in otherwise unprotected space. Depending on the UPS module rating, two or more cabinets
may be connected in parallel to provide the additional run time. This option is required to complete the UPS system.
• Maintenance Bypass—This switchboard provides make-before-break maintenance bypass. It includes: Maintenance
Bypass Breaker (MBB) and Maintenance Isolation Breaker (MIB). The Maintenance Bypass is a buyout item and not
available from Vertiv for the Liebert EXL.
• Customer Alarm Interface—This optional Input Contactor Isolator board allows the input and display of eight alarms from
customer-supplied contacts, each with a customer-selected name.
• External Control—The optional Programmable Relay Board allows the UPS to trigger external devices when a UPS event
occurs. For example, the UPS can turn On an external LED if it senses a battery cabinet temperature imbalance.
• Remote Breakers—Remote input and bypass breakers can be used instead of the internal UPS breakers. The UPS
provides connections for remote breaker status, control and voltage monitoring.
• Load Bus Synchronization (LBS)—Allows synchronizing the outputs of two or more modules when the source for one of
more modules supplied by a separate non-synchronized source.
• DC (Battery) Ground Fault—Permits setting a user-defined alarm caused by detection of a DC ground fault. An optional
input contact isolator board must be installed for processing a DC ground fault.
• Seismic Bracing—A separate kit for tying down the UPS module allows the unit to meet International Building Code (IBC).
• Remote Alarm Status Panel—Provides alarm lamps for up to eight UPS alarms. The optional power supply must be
included when purchasing this option.
• AC Ground Fault—When the unit is in discharge (battery) mode, AC ground faults are detected by the system and an
alarm is activated to the control screen.
• Module Battery Disconnect—The UPS system utilizes a separate Module Battery Disconnect (MBD) for remotely located
batteries. A sensing circuit in the UPS module, set at the battery low voltage limit, trips the Module Battery Disconnect to
safeguard the battery from excessive discharge. The Module Battery Disconnect has an undervoltage release mechanism
designed to ensure that during any shutdown or failure mode all battery potential is removed from the UPS system.
• Battery Isolation Switch—A Battery Isolation Switch (BIS) is used to isolate individual battery strings when a system MBD
is used. When the optional Battery Interface Box is used, the status of the Battery Isolation Switch is displayed on the UPS
HMI. A temperature sensor is recommended to allow proper battery charging and overtemperature protection.
• Battery Interface Box—A Battery Interface Box (BIB) is available to support the UPS and third-party battery cabinets or
rack-mounted batteries. A BIB is required for each MBD (stand-alone or inside the third-party battery cabinet). A BIB is
optional with each Battery Isolation Switch. A BIB is required for each temperature sensor.
• Temperature Sensor—Allows the UPS module to compensate battery charging voltage, depending on temperature, to
prolong battery life. The Temperature Sensor is required for battery solutions utilizing a non-matching Module Battery
Disconnect or Battery Isolation Switch. Liebert battery packs have built-in temperature sensors. The Temperature Sensor
option includes a remote sensor that must be field-installed.

Vertiv™|Liebert® EXL™ 625-1100kVA Operation and Maintenance Manual | Rev. 8 | 02/17 10
2.0 LCD TOUCHSCREEN
The Liebert EXL is equipped with a microprocessor-based human-machine interface (HMI) designed for
convenient and reliable operation. The display is driven by an easy-to- follow, menu-prompted software.
2.1 FEATURES
The Liebert EXL HMI enables the operator to perform such tasks as:
• Quickly check operational status
• Monitor the power flow through the UPS system and all meter readings
• Execute operational procedures
• Check status reports and history files
• Adjust programmable parameters (access limited by security access function)
The HMI is a touchscreen display with multicolor text and white background (see Figure 6). The display turns on
automatically, but after 15 minutes of inactivity the back-light will go out and the display will appear very dim.
Touching the screen will reactivate the back-light; the back-light will again be active for 15 minutes. If any screen
other than the mimic screen is accessed, that screen will be displayed for 5 minutes without any interaction. If
there is no activity for 5 minutes, the display will revert to the basic mimic screen.
Figure 6 Main display screen, typical
Bypass Input—The bypass circuit breaker (BFB) status is shown as Open or Closed.
UPS Input Power—The input circuit breaker (CB1) (if installed), is shown as Open or Closed.
UPS Output Power—The output circuit breaker is shown as Open or Closed.
Rectifier Block—Displays the state of the rectifier: On (solid green); Disabled (gray); Off (green outline, gray
interior); or Walking In (green outline, flashing green interior).
Inverter Block—Displays the state of the inverter: On (solid green); Disabled (gray); Off (green outline, gray
interior).
VERTIV © 2016-2017 Vertiv
Mar 14, 2017 10:15:40
ConfigReportsOperationMeteringEventsHome
+-
CB2
CB1
(E)
BFB
Inlet Air Temp: 26°C / 78°F
Liebert EXL
™
800kVA UPS Module
Mimic Display
Menu Bar

Vertiv™|Liebert® EXL™ 625-1100kVA Operation and Maintenance Manual | Rev. 8 | 02/17 11
Bypass Static Switch Block—Displays the state of the bypass static switch: On (solid green), disabled (gray),
Off (green outline, gray interior).
DC/DC Converter Block—Displays the state of the DC/DC converter: On (solid green); Disabled (gray); Off
(green outline, gray interior); or Walking In (green outline, flashing green interior).
Battery Block—Displays the state of the battery block and module battery disconnect: Normal (solid green); Fail
or High (gray); Low (yellow); and the module battery disconnect is shown as open or closed.
2.2 TOUCHSCREEN NAVIGATION
2.2.1 Main Display Screen (Home)
Several menu items can be accessed from the main display screen (see Figure 6). These menu items are
detailed in subsequent sections.
2.2.2 Configuration Menu Rating (Config)
This menu item will display a popup showing the following parameters. These parameters are entered during
commissioning when the UPS is installed by Vertiv®Services™.
Figure 7 Configuration menu
Ratings
This menu shows the basic information of the module. These parameters will set automatically based on the
other parameters entered.
• Nominal Input Voltage
• Nominal Bypass Voltage
• Nominal Output Voltage
• Nominal Source Frequency
• Nominal Output Frequency
•OutputkVA
•OutputkW
• Configuration Type
• Nominal Cell Count
VERTIV
Liebert EXL
™
800kVA UPS Module
© 2016 -2017 Vertiv
Mar 14, 2017 10 :17:44
ConfigReportsOperationMeteringEventsHome
Setting Value
Ratings
System Identification
Setpoints
Option Settings
Preferences

Vertiv™|Liebert® EXL™ 625-1100kVA Operation and Maintenance Manual | Rev. 8 | 02/17 12
System Identification
This menu shows the model numbers and serial numbers:
•UnitModelNumber
• Unit Serial Number
• Maintenance Bypass Model Number
• Maintenance Bypass Serial Number
• DC Source Cabinet Model Number
• DC Cabinet Serial Numbers
• Order Numbers
• Service Telephone Number
• Site ID Number
•ModuleLocator
•LocationID
• System Number
•ModuleLabel
Setpoints (User Adjustable)
The following will change the settings of the modules:
• Temperatures
Inlet Air Temp Warning—86°F to 104°F (30°C to 40°C) (default: 95°F [35°C])
• Bypass/Transfer
• Manual Xfer to Bypass Voltage High Limit% - 1% to 15% (default: 10%)
• Manual Xfer to Bypass Voltage Low Limit% - 1% to 20% (default: 10%)
•Output
Max Load Exceeded
The module will activate a warning when the load is above any of these settings:
• Phase A (%)—10% to 105% (default: 100%)
• Phase B (%)—10% to 105% (default: 100%)
• Phase C (%)—10% to 105% (default: 100%)
• Delay (seconds)—0 to 60 (default: 5 seconds)
• Event Management
This menu item permits changing how the Liebert EXL handles Alarms, Faults and Status information. Each event can be
configured for the following:
• Latch (yes/no)—Event stays active in the event window, even if cleared, until acknowledged (by pressing the Reset
button)
• Audible (yes/no)—Will set Audible alarm when event occurs
• Event log (yes/no)—Will display event in Event log when it occurs
•DCSource
Float Voltage
• Battery Float Voltage, VPC: 2.15 to 2.3 (default: 2.25)
•CellCountAdjustment
• Cell Count Adjustment: -12 cells to 6 cells (default: 0)
• Discharge Alarms
• Time Low Warning, minutes: 2 to 15, the upper limit is dependent on configured batteries (default: 5 minutes)
• DC Source Charging: Settings not user-adjustable
• DC Source Equalize
When Battery Equalize is activated, the module will charge the batteries to the Equalize Voltage for the length of
Equalized Time.
• Equalize Voltage, VPC—2.30 to 2.45 (default: 2.3)
• Equalize Time, hours—0 to 200 hours (default: 0)
•DCSourceTemperature

Vertiv™|Liebert® EXL™ 625-1100kVA Operation and Maintenance Manual | Rev. 8 | 02/17 13
• Battery Temp Warning—30°C to 50°C (default: 40°C)
• Battery Temp Limit—35°C to 60°C (default: 50°C)
• Disconnect—Enable/Disable (default: disabled)
Factory/Witness
• Touch Screen Calibration
Options Settings
If any Input Contact Isolator (ICI) cards or Programmable Relay Board (PRB) cards are installed, this menu will
allow these options to be configured. See 4.1 - Input Contact Isolator Board and 4.2 - Programmable Relay
Board for details on these options.
Preferences
These display settings cannot be changed from the touchscreen. Press the box to the left of each parameter to
bring a popup window that will allow the parameter to be changed.
• Time (24hr format)—Adjust Hour, Minute or Seconds
• Date (MM DD, YYYY format)—Adjust Month, Day or Year
• Password—Reset the password (up to 5 characters, alphanumeric, case-sensitive; default is EXL)
2.2.3 Reports
This menu accesses the events records.
• Event Log—Up to 2048 time- and date-stamped events are captured in the log. The oldest record will be overwritten with
a new record once the log reaches 2048 events.
NOTE
DC Source Temperature values should be set by Vertiv Services according to the battery manufacturer's
requirements.
NOTE
If Disconnect is set to Enable and the Battery Temp Limit is met, the Battery breaker will open.

Vertiv™|Liebert® EXL™ 625-1100kVA Operation and Maintenance Manual | Rev. 8 | 02/17 14
2.2.4 Metering
This menu accesses the System Meter and Battery Meter.
System Meter
Figure 8 System Meter menu
Battery Meter
• DC volts per string
• Temperature, degrees Celsius, per string
• Battery commissioning date
• Operating time on DC source
•Dischargetime
• Time remaining
•Charge%
•Amp-Hour,AH,consumed
•DCpower
• Input volts (line-line) per phase • Output amps (line-line) per phase
• Input amps (line-line) per phase • Output kVA% per phase
• Input frequency • Output kW% per phase
• Bypass volts (line-line) per phase • Output power factor (PF) per phase
• Bypass frequency • Total kVA/kW
• DC bus voltage • Output frequency
• DC bus amps • Bypass/Inverter sync window.
• Output volts (line-line) per phase
VERTIV
Liebert EXL
™
800kVA UPS Module
© 2016-2017 Vertiv
Mar 14, 2017 10:15:40
Inlet Air Temp: 26°C / 78°F
+-
CB2
CB1
(E)
BFB
Reset Silence Input A B C
Volts L-L 492 499 497
Amps 55 52 51
Freq Hz 60.0
Bypass A B C
Volts L-L 491 500 496
Freq Hz 60.0
DC Source
Volts 538
Amps Float
Output A B C
Volts L-L 481 481 482
Amps 0 0 0
kVA% 0 0 0
kW% 0 0 0
PF 0.00 0.00 0.00
kVA/kW 0/0
Freq Hz 60.0
Bypass/Inverter Sync
Inverter leads Bypass by 3 degrees
ConfigReportsOperationMeteringEventsHome
-30 +300-- - -- -