Viessmann VITOTROL 100-E User manual

Operating instructions
for the system user
VIESMANN
Vitotrol 100-E
Wireless remote control for 1 heating circuit
VITOTROL 100-E
6192459 GB 7/2022 Please keep safe.

2
Please follow these safety instruc-
tions closely to prevent accidents
and material losses.
Safety instructions explained
Danger
This symbol warns against the risk
of injury.
Note
Details identified by the word "Note"
contain additional information.
Target group
These instructions are intended for sys-
tem users.
This appliance can also be operated by
children aged 8 and older, as well as by
individuals with reduced physical, sen-
sory or mental faculties or those lacking
in experience and knowledge, provided
such individuals are supervised or have
been instructed in the safe use of this
appliance and any risks arising from it.
Danger
Wireless signals can interfere with
electronic medical devices,
particularly pacemakers, hearing
aids and defibrillators.
If any such equipment is fitted,
users should avoid being in the
immediate vicinity of operational
wireless components.
Installation and adjustment
■All settings and work on the device
must be carried out as specified in
these instructions.
■Observe minimum clearances to
ensure reliable signal transmission.
Operation of the system
■Only operate the devices inside closed
buildings.
■Never operate devices in rooms where
there is a risk of explosion.
■Protect devices from:
–Moisture
–Dust
–Liquids
–Vapours
–Direct sunlight
–Other direct thermal radiation
■After a restart, check the status of the
wireless components.
Danger
Damaged equipment poses a
safety hazard.
Check the appliance for external
damage. Never start up a damaged
appliance.
Safety instructions
Safety instructions
6192459

3
Auxiliary components and individual parts
For replacement, use only spare parts
supplied or approved by Viessmann.
Safety instructions
Safety instructions (cont.)
6192459

4
1. Safety and liability Operational reliability and system requirements .................................... 6
Liability ................................................................................................... 6
2. Introductory information Disposal of packaging ............................................................................ 7
Symbols ................................................................................................. 7
Terminology ........................................................................................... 7
Contractor .............................................................................................. 7
Intended use .......................................................................................... 8
Product information ................................................................................ 8
■Maintenance parts and spare parts .................................................... 8
Commissioning ...................................................................................... 9
■Control unit of Viessmann appliance .................................................. 9
■Remote control ................................................................................... 9
Your system has been preset ................................................................ 9
Energy saving tips ................................................................................. 9
Tips for greater comfort ......................................................................... 10
3. Preparing for installation Installation location ................................................................................ 11
■Checking the reception quality at the installation location .................. 11
■Range of the wireless signal ............................................................... 11
■Angle of penetration ........................................................................... 12
4. Installation sequence Overview of the installation and commissioning process ...................... 13
Fitting the mounting base ...................................................................... 13
Establishing a power supply via batteries .............................................. 13
5. Commissioning Adjusting your Viessmann appliance ............................................. 15
■Commissioning the Vitotrol 100-E ...................................................... 15
Inserting the Vitotrol 100-E in the mounting base .................................. 16
6. Using the remote control Using the remote control ........................................................................ 17
■Overview of controls ........................................................................... 17
Operating programs for central heating and DHW heating ................... 18
■Special operating programs and functions ......................................... 19
Procedure for setting a time program .................................................... 19
■Time programs and time phases ........................................................ 19
■Setting time phases ............................................................................ 20
■Deleting time phases .......................................................................... 21
7. Central heating Adjusting the room temperature ............................................................ 22
■Changing the room temperature for the current temperature level .... 22
■Changing the room temperature for further temperature levels ......... 22
■Time program for central heating ........................................................ 22
Switching central heating on or off ......................................................... 22
Temporarily adjusting the room temperature ......................................... 23
■Switching on "Extended heating"/"Extend time phase once" ........ 23
■Switching off "Extended heating"/"Extend time phase once" ........... 23
8. DHW heating Starting DHW heating ............................................................................ 24
■Switching off DHW heating ................................................................. 24
Setting the DHW temperature ................................................................ 24
Time program for DHW heating ............................................................. 24
■Setting a time program ....................................................................... 24
9. Further settings Setting or changing the language .......................................................... 25
Enabling the "Lock controls" (child lock) function .................................. 25
Software update ..................................................................................... 25
Setting the format of the day and time display ....................................... 25
Restoring factory settings ...................................................................... 26
Index
Index
6192459

5
10. Diagnosis and service
checks
Calling up device information ................................................................. 27
■Displaying "DEV INFO" ...................................................................... 27
Correcting the actual room temperature displayed ................................ 27
Messages shown on the display ............................................................ 27
11. What to do if... Faults without fault display ..................................................................... 29
Cause of fault could not be found .......................................................... 29
Restarting the Vitotrol 100-E .................................................................. 29
12. Maintenance Replacing the batteries .......................................................................... 31
Cleaning ................................................................................................. 32
13. Specification ................................................................................................................ 33
14. Appendix Licences ................................................................................................. 34
■APACHE-LIZENZ/Version 2.0 ............................................................. 34
Terminology ........................................................................................... 36
■Standby mode .................................................................................... 36
■Setback mode (reduced heating mode) ............................................. 36
■Operating program ............................................................................. 36
■Screed drying ..................................................................................... 36
■Underfloor heating system .................................................................. 37
■Heating mode ..................................................................................... 37
■Heating circuit ..................................................................................... 37
■Night setback ...................................................................................... 37
■Room heating ..................................................................................... 37
■Room temperature .............................................................................. 38
■Actual room temperature .................................................................... 38
■Set temperature .................................................................................. 38
■Time program ..................................................................................... 38
Final decommissioning and disposal of the remote control ................... 38
15. Certification ................................................................................................................ 39
16. Keyword index ................................................................................................................ 40
Index
Index (cont.)
6192459

6
System safety:
■The heating system and the functionality of the mes-
sage paths must be tested at regular intervals.
■To improve the operational reliability of the heating
system, we recommend implementing supplemen-
tary measures, e.g. frost protection or monitoring for
water damage.
Reliable remote control operation:
■The control unit of the Viessmann appliance and the
Vitotrol 100-E remote control must be connected via
low power radio.
■At least 1 heating circuit must be assigned to the
remote control (settings to be made by the contractor
via software tool).
■Commissioning has been carried out.
■For a software update, the Viessmann appliance has
to be connected to the internet via a WiFi router. The
download always takes place via the Viessmann
server.
Automatic software updates are only carried out if a
permanent internet connection is available via the
Viessmann appliance (recommendation).
Settings for WiFi and low power radio at the
connected Viessmann appliance:
Operating instructions for the Viessmann appli-
ance
Liability
No liability is accepted for loss of profit, unattained
savings, or other direct or indirect consequential losses
resulting from use of the Vitotrol remote control, the
Viessmann server or the software, or for damage
resulting from inappropriate use.
Liability is limited to typical damage arising if a funda-
mental contractual obligation is violated through slight
negligence, the fulfilment of which is essential for
proper execution of the contract.
The limitation of liability shall not apply if the damage
was caused deliberately or through gross negligence,
or if mandatory liability applies due to product liability
legislation.
The Viessmann General Terms and Conditions apply,
which are included in each current Viessmann pricelist.
Viessmann accepts no liability for push notifications
and email services, which are provided by network
operators. The terms and conditions of the relevant
network operators apply in this context.
Safety and liability
Operational reliability and system requirements
6192459
Information

7
Please dispose of packaging waste in line with statu-
tory regulations.
Symbols
Symbol Meaning
Reference to other document containing
further information
1.
Step in a diagram:
The numbers correspond to the order in
which the steps are carried out.
Warning of material losses and environ-
mental pollution
Live electrical area
Pay particular attention.
■Component must audibly click into place.
or
■Acoustic signal
■Fit new component.
or
■In conjunction with a tool: Clean the sur-
face.
Dispose of component correctly.
Dispose of component at a suitable collec-
tion point. Do not dispose of component in
domestic waste.
Terminology
To provide you with a better understanding of the func-
tions of your remote control, some terminology is
explained. This information can be found in chapter
"Terminology" in the Appendix.
Contractor
Activities that may only be carried out by the con-
tractor are indicated with this symbol.
Work on electrical equipment may only be carried out
by a qualified electrician.
Introductory information
Disposal of packaging
6192459
Information

8
Install and operate the Vitotrol 100-E as intended and
only in conjunction with the electronic control units and
controllers of the Viessmann appliances that are sup-
ported for this purpose.
The Vitotrol 100-E is exclusively designed for opera-
tion in buildings of a residential or commercial nature.
Incorrect use of the device is prohibited and will result
in an exclusion of liability (e.g. commercial or industrial
use other than for control and monitoring purposes).
Installation, service and operating instructions included
with the product and available online must be
observed.
Use the Vitotrol 100-E exclusively for system operation
with the communication interfaces specified for this
purpose in the relevant product documentation. With
regard to the communication interfaces, ensure on site
that the system requirements specified in the product
documentation are met at all times for every transfer
medium employed.
Note
The device is intended exclusively for domestic or
semi-domestic use, i.e. even users who have not had
any instruction are able to operate the device safely.
Product information
The Vitotrol 100-E is a wireless remote control for
Viessmann appliances, e.g. heat generators. The
Vitotrol 100-E is connected to the control unit of the
Viessmann appliance via "low power radio". For opera-
tion with a Vitotrol 100-E, the control unit of the Viess-
mann appliance must be set to "15: Individual room
control (On/Off)" or "16: Individual room control
with modulation (modulation control)" during com-
missioning using the ViGuide software tool (depending
on the remote control version).
1 heating circuit can be operated with the
Vitotrol 100-E. The Vitotrol 100-E can be used to set
room temperatures and operating programs, or call up
fault messages.
Ambient temperatures: +5 to +40 °C
The Vitotrol 100-E may be used in rooms with moder-
ate or low humidity.
Note
No more than 1 Vitotrol 100-E can be configured for
each control unit.
Up to date information on the remote control
For a current overview of the supported control units
and updates for the product, e.g. information on com-
missioning: See www.vitotrol.info.
Maintenance parts and spare parts
Maintenance parts and spare parts can be identified and ordered directly online.
Viessmann Partnershop
Login:
https://shop.viessmann.com/
Viessmann spare part app
www.viessmann.com/etapp
Introductory information
Intended use
6192459
Information

9
Control unit of Viessmann appliance
The commissioning and matching of the control unit to
local conditions and building characteristics, as well as
instructing the user in the operation of the system, is
carried out by your contractor.
During commissioning, the control unit settings are
transferred to the remote control.
Remote control
Commissioning of the Vitotrol 100-E: See page
14 15.
Your system has been preset
The control unit preset at the factory.
Operating instructions for the Viessmann appli-
ance
The range of functions and displays on your remote
control depends on the control unit it is connected to,
its settings and the equipment of the system overall.
Your contractor can make further adjustments for you
during commissioning.
You can change the settings at any time to suit your
individual requirements.
Power failure
All settings are saved if there is a power failure.
Energy saving tips
Saving energy when using central heating
■Do not overheat your home. Every degree of room
temperature reduction saves up to 6 % on your heat-
ing bills.
Do not set your individual preferred temperature too
high, e.g. not above 20 °C: See page 22.
■Heat your home to the reduced room temperature at
night or during regular absences (not applicable to
underfloor heating). To do this, set the time programs
for central heating.
■To switch off functions that are not required (e.g.
central heating in summer), select the "Only DHW"
and "Standby mode" operating programs.
Operating instructions for Viessmann heat
generator
Saving energy on DHW heating
■At night or during regular absences, heat the DHW to
a lower temperature. To do this, set the time program
for DHW heating.
■Switch on DHW circulation only for those times in
which you regularly use hot water. To do so, adjust
the settings in the time program for the DHW circula-
tion pump. This setting can only be made at the con-
trol unit of the Viessmann appliance.
Operating instructions for Viessmann heat
generator
For additional energy saving functions, e.g. on the con-
trol unit, please contact your contractor.
Introductory information
Commissioning
6192459
Information

10
More comfort in your home
■Set your individual preferred temperature: See
page 22.
■Set the time program for your heating circuits such
that your individual preferred temperature is auto-
matically reached when you are present.
■If you need a higher room temperature for a short
time, select the "Extended heating""Extend time
phase once" function: See page 23 22.
Example: Late in the evening, the reduced room
temperature is set by the time program. Your guests
stay longer.
Sufficient DHW heating for your needs
■Set the time program for DHW heating such that
there is always sufficient hot water for your usual
needs: See page 24.
Example:
You need more DHW in the morning than in the day-
time.
■Set the time program for the DHW circulation pump
so that at times when hot water is used frequently,
DHW is available immediately from the taps. This
setting can only be made at the control unit of the
Viessmann appliance.
Operating instructions for Viessmann heat
generator
Introductory information
Tips for greater comfort
6192459
Information

11
Install your remote control on a wall.
■Installation only in enclosed buildings
■The installation location must be dry and free of frost.
■Ensure ambient temperatures between +5 and
+40 °C.
■Never seal off the vent apertures of the
Vitotrol 100-E.
■Distance to floor min. 1.5 m
■Not next to windows or doors
■Not above radiators
■Not between shelves, in recesses, etc.
■Not near heat sources (direct insolation, fireplace,
TV set, etc.)
■Away from vents
Note
To ensure a good wireless connection, keep the dis-
tance between the Vitotrol 100-E and the Viessmann
appliance as short as possible.
Check the reception quality at the intended installation
site: See the following chapter.
Checking the reception quality at the installation location
In order to check the reception quality at the intended
installation location, first start the Vitotrol 100-E: See
page 14 15.
Tap the following buttons:
1.
2. / for "DEV INFO"
3. OK
4. / for "RF RANGE"
5. OK
The signal strength "RF RANGE" for this mounting
position is displayed. For an explanation of the dis-
plays, see the following table.
Note
■The poorer the reception quality, the longer it takes
for the Vitotrol 100-E to establish a connection to the
Viessmann appliance. It can take up to 6 minutes to
establish the connection.
■A poor connection can result in the batteries running
out sooner.
■To ensure a stable wireless connection, we recom-
mend a signal strength of at least –75 dBm: See the
following table.
Meaning of display
Value in dBm Reception quality
0 to –50 Very good
–51 to –65 Good
–66 to –75 Adequate
–76 to –85 Inadequate
–86 to –... No reception
The values given in the table are meant as guide val-
ues. The connection may vary depending on local con-
ditions.
Range of the wireless signal
The range of wireless signals may be reduced by
walls, ceilings and interior fixtures. These weaken the
wireless signal, causing poor reception due to the fol-
lowing circumstances.
■On their way between transmitter and receiver, wire-
less signals are damped, e.g. by air or when pene-
trating walls.
■Wireless signals are reflected by metallic objects
e.g. reinforcements embedded in walls, metal foil of
thermal insulation and thermal glazing with metal-
lised thermal vapour deposit.
■Wireless signals are isolated by service ducts and
lift shafts.
■Wireless signals are disrupted by devices that also
operate with high frequency signals. Maintain a dis-
tance of at least 2 m from these devices:
–Computers
–Audio and video systems
–Devices with active WiFi connection
–Electronic transformers
–Pre-ballasts
Preparing for installation
Installation location
6192459
Installation

12
To extend the range of the wireless signal, the follow-
ing repeaters can be used:
■Viessmann ViCare repeater for surface mounting
■Ubisys repeater
Angle of penetration
The reception quality remains best if radio signals hit
the walls vertically.
Depending on the angle of penetration, the effective
wall thickness changes and so does the extent to
which the electromagnetic waves are damped.
Flat (unfavourable) angle of penetration
B
A
C
Fig. 1
AVitotrol 100-E
BViessmann appliance
CWall
Ideal angle of penetration
C
B
A
Fig. 2
AVitotrol 100-E
BViessmann appliance
CWall
Preparing for installation
Installation location (cont.)
6192459
Installation

13
Steps Responsibility Page
1 Check system requirements. Contractor
IT expert
6
2 Fit the mounting base for the Vitotrol 100-E. Contractor
System user
13
3 Establish a power supply via batteries. Contractor
System user
13
4 Commission the Vitotrol 100-E. Contractor
System operator
15
5 Insert the Vitotrol 100-E in the mounting base. Contractor
System operator
16
Fitting the mounting base
2x
2.
1.
Fig. 3
Establishing a power supply via batteries
We recommend the use of AA batteries as they last
longer than rechargeable ones.
Installation sequence
Overview of the installation and commissioning process
6192459
Installation

14
2 x AA 2 x 1,5 V
Fig. 4
Installation sequence
Establishing a power supply via batteries (cont.)
6192459
Installation

15
1. During commissioning, set the Viessmann appli-
ance to "15: Individual room control (On/Off)" or
"16: Individual room control with modulation
(modulation control)" using the ViGuide software
tool.
Installation and service instructions of the
Viessmann appliance
2. To connect your Viessmann appliance to the
Vitotrol 100-E, activate "low power radio" at the
control unit of your Viessmann appliance.
Operating instructions for the Viessmann
appliance
3. Install the ViGuide mobile app from the Apple App
Store or Google Play Store on your mobile device.
4. Follow the instructions in the app to register.
5. Assign the Vitotrol 100-E to your Viessmann appli-
ance via ViGuide.
Commissioning the Vitotrol 100-E
After the batteries are inserted, the Vitotrol 100-E
switches on and shows the following information on
the display:
"SW VERS": Software version of the appliance
Press the following buttons:
01. OK for "LANGUAGE"
02. / to set the required language.
03. OK to confirm.
"FORMAT" is displayed
04. / to select the required time format.
05. OK to confirm.
"WEEK TYPE" is displayed.
06. / to select whether days of the week
should be displayed as "NUMBER" or "WORD".
07. OK to confirm.
"STARTPAIR" is displayed.
08. OK to confirm.
"PAIRING" is displayed.
While the connection to the Viessmann appliance
is being established, a percentage progress indi-
cator "PROC" is displayed.
09. Install the ViGuide mobile app from the Apple App
Store or Google Play Store on your mobile device.
10. Launch the ViGuide mobile app.
11. Follow the instructions in the app to establish the
connection to your Viessmann appliance.
Note
To cancel the connection attempt, press .
■The connection attempt is displayed via a pro-
gress bar in percent.
■It can take up to 5 minutes to establish the con-
nection.
■The settings of the Viessmann appliance were
transferred to the Vitotrol 100-E during commis-
sioning.
■If the connection to your Viessmann appliance
could not be established, the Vitotrol 100-E dis-
play will show "RETRY". Press OK to restart the
connection attempt.
12. Adjust the settings of e.g. the set room tempera-
ture to match the system.
Commissioning
Adjusting your Viessmann appliance
6192459
Commissioning

16
Fig. 5
Commissioning
Inserting the Vitotrol 100-E in the mounting base
6192459
Commissioning

17
Overview of controls
The Vitotrol 100-E remote control enables you to
adjust the following settings from the living space:
■Set room temperatures
■Time program heating
■DHW heating:
–DHW temperature
–Time program
■Heating circuit: Activate/deactivate "Extended heat-
ing"/"Extend time phase once"
All settings are transferred from the Vitotrol 100-E to
the Viessmann appliance and vice versa. It is always
the most recent settings that apply. During commis-
sioning, the settings of the Viessmann appliance were
already transferred to the remote control.
A
B
C
Fig. 6
ADisplay
BOperating buttons
CRoom temperature sensor aperture:
Never seal!
Operating buttons
■On the home screen:
Opens the settings menu.
If pressed for longer (approx. 3 seconds),
the Vitotrol 100-E switches to standby
mode.
■Within the settings menu:
Takes you one step back in the menu.
If pressed for longer (approx. 3 seconds),
you return directly to the home screen
without saving the settings you had made.
/ Scrolls through the menu.
OK Confirms your selection or change.
On the home screen:
If pressed for longer (approx. 3 seconds),
you activate/deactivate the operating buttons
(child lock). The "child lock" function must be
activated once in the menu for this; see
page 25.
Activates/deactivates the "Extended heat-
ing"/"Extend time phase once" function.
Takes you directly to the submenu, where
you can set room temperatures for the tem-
perature levels.
Home screen
ABC
Fig. 7 Possible home screen, depending on the cur-
rent operating state
ADisplay of different symbols depending on the cur-
rent operating state
BCurrent actual room temperature
CCurrent time
Symbols on the display
These symbols are not always displayed, but appear
subject to the system version and the operating state.
General symbols
Indicates that the low power radio connection to
the Viessmann appliance has been established.
Child lock is active.
Temperatures
Room heating with reduced room temperature
Room heating with normal room temperature
Room heating with comfort room temperature
Backs up DHW heating in On/Off status or by
schedule (Auto mode), depending on the Viess-
mann appliance.
Using the remote control
Using the remote control
6192459
Operation

18
Operating programs
Frost protection is active.
Heating is active.
"Extended heating"/"Extend time phase once"
is active.
DHW is heated according to the time pro-
gram.
DHW heating is permanently off.
DHW heating is permanently on.
Messages
Fault
Replace the batteries.
Symbols during operation
While settings are being made.
Time program: Active time phase
Standby
If no settings are made at the remote control for at
least 5 seconds, the display backlighting switches off.
To end standby:
Press any button.
The display lights up. The home screen is displayed.
Locking/unlocking the controls
To activate/deactivate the operating buttons (child
lock), press OK for approx. 3 seconds. The "child lock"
function must be activated once; see page 25.
Operating programs for central heating and DHW heating
Note
The operating programs for central heating and DHW
heating can be set separately.
Display Operating program Function
Room heating
and one of the following sym-
bols is displayed:
■
■
■
"Heating mode" The rooms of the selected heating circuit
are heated in accordance with the specifica-
tions for the room temperature and the time
program (see chapter "Central heating").
The symbol is no longer dis-
played.
"Standby mode" ■No central heating
■Frost protection for the Viessmann appli-
ance is active.
"Standby mode" can only be activated and
deactivated on the Viessmann appliance.
To switch off heating via the Vitotrol 100-E,
the lowest settings for the temperature lev-
els can only be selected in the "heating
mode" operating program.
DHW heating
DHW heating according to time
program
DHW is heated in accordance with the spec-
ifications for the DHW temperature and the
time program (see chapter "DHW heating").
DHW heating is permanently
on.
DHW is permanently heated to the set DHW
temperature regardless of a time program
(see chapter "DHW heating").
DHW heating is permanently
off.
■No DHW heating (see chapter "DHW
heating")
■Frost protection for the DHW cylinder is
enabled.
Using the remote control
Using the remote control (cont.)
6192459
Operation

19
Special operating programs and functions
■Screed drying:
This function is activated by your contractor at the
control unit of the Viessmann appliance (if the Viess-
mann appliance supports this function). Your screed
is dried in line with a set time program (temperature/
time profile) suitable for the relevant building materi-
als. Your settings for room heating have no effect on
the duration of screed drying (max. 32 days). The
system no longer provides DHW heating. The
"Screed drying" function can be altered or switched
off by your contractor.
Control unit of the Viessmann appliance
■External hook-up:
The operating program set at the control unit was
changed over by an external device, e.g. an EM-EA1
extension (DIO electronics module). The operating
program cannot be changed via the control unit or
remote control while the external hook-up is active.
Control unit of the Viessmann appliance
■"Extended heating"/"Extend time phase once":
See page 23.
Procedure for setting a time program
The following explains how to enter the settings for a
time program. The specifics of the individual time pro-
grams can be found in the relevant chapters.
Time programs and time phases
In the time programs, you specify what your heating
system should do at what time. To do so, divide the
day into sections. These are called time phases. Dif-
ferent temperature levels are enabled within and out-
side these time phases.
You can set up a time program for the following functions:
Function Setting on the
Viessmann device
Function
Within the time phase Outside the time phase
Central heating ■Remote control
■Control unit of the
Viessmann appli-
ance
Your rooms are heated to stand-
ard room temperature or com-
fort room temperature.
Your rooms are heated to re-
duced room temperature.
DHW heating ■Remote control
■Control unit of the
Viessmann appli-
ance
DHW heating is switched on.
The water in the DHW cylinder
is heated to the set DHW tem-
perature.
Domestic hot water heating is
switched off.
Using the remote control
Operating programs for central heating and DHW… (cont.)
6192459
Operation

20
Setting time phases
Explanation of the procedure using the example of
room heating
You can set up to 4 time phases in each "Time pro-
gram".
For each time phase, you define the start point
"START" and the end point "END".
Example:
"Time program" for "Monday"
■Time phase 1:
06:30 to 12:00 with the normal room temperature
■Time phase 2:
15:00 to 20:00 with comfort room temperature
In between these time phases the rooms are heated
with the reduced temperature .
Press the following buttons:
1.
2. / for "SCHEDULE"
3. OK to confirm
4. / for a group of days or a single day
"MO-FR" Set the same time phase for all days.
"SA-SU" Set the same time phase for all days
of the weekend.
"MO-SU" Set the same time phase for all days.
, ... Set the time phase for individual
days.
The days are shown in abbreviated
form or as numbers. To change the
type of display, see page 25.
How the days of the week are shown:
5. OK to confirm
Changing time phase 1:
If you want to start changing another time phase, use
/ to select it and confirm with OK.
01. / to set the hour for the start of the time
phase ("START") to 6.
02. OK to confirm.
03. / to set the minutes for the start of the time
phase ("START") to 30 minutes.
04. OK to confirm
05. / for the required temperature level
"NORMAL"
06. OK to confirm
07. / to set the hour for the end of the time
phase ("END") to 12.
08. OK to confirm.
09. / to set the minutes for the end of the time
phase ("END") to 00 minutes.
10. OK to confirm
Setting new time phase 2:
01. / to set the hour for the start of the time
phase ("START") to 15.
02. OK to confirm.
03. / to set the minutes for the start of the time
phase ("START") to 00 minutes.
04. OK to confirm
05. / for the required temperature level
"COMFORT"
06. OK to confirm
07. / to set the hour for the end of the time
phase ("END") to 22.
08. OK to confirm.
09. / to set the minutes for the end of the time
phase ("END") to 00 minutes.
10. OK twice to confirm
Finalising the time phase settings:
If a setting is not made for all possible time phases, the
first time phase that is not used must be set to "--:--".
Only then are the time phase settings finalised
1. / to set the hour for the start of the time
phase ("START") to --:--.
2. OK twice to confirm.
Using the remote control
Procedure for setting a time program (cont.)
6192459
Operation