Viessmann VITOTROL 200 RF Quick guide

Installation and service
instructions
for contractors
VIESMANN
Vitotrol 200 RF
Wireless remote control for one heating circuit
For applicability, see the last page
VITOTROL 200 RF
5602 119 GB 3/2011 Please keep safe.

2
Please follow these safety instructions closely to prevent accidents and mate-
rial losses.
Safety instructions explained
Danger
This symbol warns against the
risk of injury.
!Please note
This symbol warns against the
risk of material losses and envi-
ronmental pollution.
Note
Details identified by the word "Note" con-
tain additional information.
Target group
These instructions are exclusively
designed for qualified personnel.
■ Work on gas equipment must only be
carried out by a qualified gas fitter.
■ Work on electrical equipment must
only be carried out by a qualified elec-
trician.
■ The system must be commissioned by
the system installer or a qualified per-
son authorised by the installer.
Regulations
Observe the following when working on
this system
■ all legal instructions regarding the pre-
vention of accidents,
■ all legal instructions regarding envi-
ronmental protection,
■ the Code of Practice of relevant trade
associations,
■ all current safety regulations as
defined by DIN, EN, DVGW, TRGI,
TRF, VDE and all locally applicable
standards,
■ Gas Safety (Installation & Use) Regu-
lations
– the appropriate Building Regulation
either the Building regulations, the
Building Regulation (Scotland),
Building Regulations (Northern Ire-
land),
– the Water Fittings Regulation or
Water Bylaws in Scotland,
– the current I.E.E. Wiring Regula-
tions.
If you smell gas
Danger
Escaping gas can lead to explo-
sions which may result in serious
injury.
■ Never smoke. Prevent naked
flames and sparks. Never
switch lights or electrical appli-
ances ON or OFF.
■ Close the gas shut-off valve.
■ Open windows and doors.
■ Remove all people from the
danger zone.
■ Notify your gas or electricity
supplier from outside the build-
ing.
■ Shut off the electricity supply to
the building from a safe place
(outside the building).
Safety instructions
Safety instructions
5602 119 GB

3
If you smell flue gas
Danger
Flue gas can lead to life-threat-
ening poisoning.
■ Shut down the heating system.
■ Ventilate the boiler room.
■ Close all doors leading to the
living space.
Working on the system
■ When using gas as fuel, also close the
main gas shut-off valve and safeguard
against unauthorised reopening.
■ Isolate the system from the power sup-
ply and check that it is no longer 'live',
e.g. by removing a separate fuse or by
means of a main isolator.
■ Safeguard the system against unau-
thorised reconnection.
!Please note
Electronic modules can be dam-
aged by electro-static dis-
charges.
Touch earthed objects, such as
heating or water pipes, to dis-
charge static loads.
Repair work
!Please note
Repairing components which ful-
fil a safety function can compro-
mise the safe operation of your
heating system.
Replace faulty components only
with original Viessmann spare
parts.
Ancillary components, spare and
wearing parts
!Please note
Spare and wearing parts which
have not been tested together
with the heating system can com-
promise its function. Installing
non-authorised components and
non-approved modifications/con-
version can compromise safety
and may invalidate our warranty.
For replacements, use only orig-
inal spare parts from Viessmann
or those which are approved by
Viessmann.
Safety instructions
Safety instructions (cont.)
5602 119 GB

4
Installation instructions
Installation sequence
Usage information................................................................................................ 5
Installation location............................................................................................... 5
Commissioning the Vitotrol 200 RF...................................................................... 6
Checking the transmission and reception quality at the installation site.............. 8
Fitting the wall mounting base.............................................................................. 9
Inserting and removing the remote control........................................................... 9
Changing the heating circuit assignment following commissioning..................... 10
Changing the display contrast.............................................................................. 11
Service instructions
Troubleshooting
Fault display......................................................................................................... 12
Specification....................................................................................................... 13
Parts list.............................................................................................................. 14
Index
Index
5602 119 GB

5
The Vitotrol 200 RF can be connected to
a Vitotronic control unit only in conjunc-
tion with the associated wireless base
station.
Up to three Vitotrol 200 RF can be log-
ged on at the same time at the wireless
base station of a Vitotronic control unit.
Installation location
Operation with or without room temperature hook-up
■Weather-compensated mode
Installation in any room.
■Operation with room temperature
hook-up
– On an internal wall in the main living
room, at a height of approx. 1.5 m
from the floor
– Not near windows or doors
– Not above radiators
– Not near heat sources (direct sun-
light, fireplace, TV set etc.)
Do not install further control devices in
this room. Any thermostatic radiator
valves must always be fully opened.
Wireless connection
Select the installation site of the Vitotrol
200 RF and the wireless base station so
that the radio signals are beamed as ver-
tically as possible onto walls and furnish-
ings.
Installation and service instruc-
tions, wireless base station
Note
Conducting metallic materials have a
strong negative effect on reception.
Prior to the final fitting at the preferred
installation site, commission the Vitotrol
200 RF and check the transmission and
reception quality at the installation site.
Installation sequence
Usage information
5602 119 GB
Installation

6
Prior to commissioning, observe the
following:
■ The wireless base station must be
connected with the control unit via a
KM BUS.
■ The control unit to which the wireless
base station is connected must be
switched on.
+ - + -
1. Site all the Vitotrol 200 RF near the
wireless base station.
n
2. Insert batteries (LR 6/AA, included in
the standard delivery) into the remote
control unit.
The configuration assistant then
starts automatically.
The display shows "CI" and "Lrn"
flashes.
Installation sequence
Commissioning the Vitotrol 200 RF
5602 119 GB

7
A
3. Press A on the wireless base sta-
tion:
■ Operation without wireless repeat-
ers: for 4 s. The green LED on the
wireless base station flashes
slowly.
■ Operation with wireless repeaters:
for 8 s. The green LED on the wire-
less base station flashes quickly.
Installation and service
instructions, wireless base
station
4. On the remote control, press OK.
The remote control unit transmits a
signal to log on at the wireless base
station.
■ Log on successful:
The display shows "C2" and
"000" (first digit flashes).
■ Log on unsuccessful:
The display shows "_ _ _ _ " and
.
Repeat the log on process.
5. Following successful log on, enter the
3-digit PIN at the remote control. The
PIN is printed on the protective foil on
the front of the wireless base station.
■ With +/- enter the first digit, then
confirm with OK.
■ With select the next position and
enter the next figure with +/-.
■ Confirm each entry with OK.
6. After the complete PIN has been
entered, "C3" and "H 1" will be
shown.
Then assign the required heating cir-
cuit (see the following chapter).
Installation sequence
Commissioning the Vitotrol 200 RF (cont.)
5602 119 GB
Installation

8
Assigning a heating circuit
1. Select the required heating circuit
with +/-:
■ Heating circuit 1 – "H 1"
■ Heating circuit 2 – "H 2"
■ Heating circuit 3 – "H 3"
2. OK to confirm.
The operating state of the heating
system is transferred.
The display segments rotate (for up
to 5 min).
Checking the transmission and reception quality at the instal-
lation site
1. Position the Vitotrol 200 RF at its
intended installation site.
2. Press OK and simultaneously for
approx. 4 s.
The display shows "dI" and "H .." for
the assigned heating circuit.
3. Call up a display of the transmission
and reception quality with / :
■ "d2": Vitotrol 200 RF
■ "d3": Wireless base station
■ "d4": Outside temperature sen-
sor RF
See the following table.
4. If the transmission and reception
quality is inadequate, either select a
different installation site and repeat
the check or use a wireless
repeater.
Display Value Transmission and reception quality
0 to - 78 extremely good
- 79 to - 83 good
- 84 to - 87 adequate
- 88 to - 91 inadequate
- 92 to - ... no reception
Installation sequence
Commissioning the Vitotrol 200 RF (cont.)
5602 119 GB

9
Inserting and removing the remote control
Insertion
2.
1.
Installation sequence
Fitting the wall mounting base
5602 119 GB
Installation

10
Removal
2.
1.
Changing the heating circuit assignment following commis-
sioning
1. Press and simultaneously at the
remote control for approx. 4 s.
2. With / select "C3".
3. With +/- select heating circuit 1
("H 1"), heating circuit 2 ("H 2") or
heating circuit 3 ("H 3").
4. OK to confirm.
The operating state of the heating
system is transferred.
The display segments rotate (for up
to 5 min).
Adjustments at the Vitotronic control
unit:
Set coding address "A0" for this heating
circuit at the control unit to 0 (fault mes-
sage bC, bd, bE).
Installation sequence
Inserting and removing the remote control (cont.)
5602 119 GB

11
Installation and service instruc-
tions or service instructions of the
control unit
Changing the display contrast
1. Press and simultaneously at the
remote control for approx. 4 s.
2. With / select "C4".
3. Change the contrast with +/-.
In the delivered condition, an average
value (3) has been set.
4. OK to confirm.
Installation sequence
Changing the heating circuit assignment… (cont.)
5602 119 GB
Installation

12
The symbol flashes on the display if a
fault has occurred.
For troubleshooting, see the
installation and service instruc-
tions of the relevant control unit.
If the display shows "_ _ _ _ " and , then
the wireless connection has been lost or
has not yet built.
For troubleshooting, log components off
and then back on again. If required, use
wireless repeaters (accessories).
Installation and service instruc-
tions, wireless base station.
Troubleshooting
Fault display
5602 119 GB

13
Power supply 2 batteries
LR 6/AA/
Mignon
3 V–,
2600 mAh
Battery service life approx. 2 years
Radio frequency 868.3 MHz
Safety category III
IP rating IP 30
Permissible ambient temperature
■ during operation 0 to +40 °C
■ during storage and
transportation
−20 to +65 °C
Set room temperature
range 3 to 37 °C
Specification
Specification
5602 119 GB
Service

14
When ordering spare parts
Quote part no. 7441652 and the position
no. of the part (as per this parts list).
Obtain standard parts from your local
supplier.
Parts
017 Wall mounting base
018 Programming unit
Parts not shown
080 Installation and service instructions
081 Operating instructions
017
018
Parts list
Parts list
5602 119 GB

15
5602 119 GB
Service

16
Applicability
Serial No.:
7441652
Viessmann Limited
Hortonwood 30, Telford
Shropshire, TF1 7YP, GB
Telephone: [phone]
Fax: [phone]
E-mail: [email protected]
Viessmann Werke GmbH&Co KG
D-35107 Allendorf
Telephone: [phone]
Fax: [phone]
www.viessmann.com
5602 119 GB Subject to technical modifications.
Printed on environmentally friendly,
chlorine-free bleached paper