VIRTUFIT VFROWWRB User manual

@virtufit_fitness
VirtuFit
www.virtufit.com
ASSEMBLY
VIDEO
USER MANUAL
Elite Water Resistance Black + Oak Edition
VFROWWRB + VFROWWRO
1
Instruction Manual
Rowing machine
Please read the instruction manual before installing and using the product.
SERIAL NUMBER
SERIENNUMMER
SERIENUMMER
NUMERO DE SERIE

USER MANUAL
02
USER MANUAL
TOOLKIT
# DESCRIPTION QTY
A Rowing machine 1
B Pedal 1
C Hand pump 1
D Funnel 1
E Cushion 1
F Rear connecting plate 1
NOTE! Do not connect the unit to the power supply until it is fully assembled.
LET OP! Sluit het toestel pas aan op het stroom wanneer het volledig is gemonteerd.
HINWEIS! Schließen Sie das Gerät erst dann an das Stromnetz an, wenn es vollständig montiert ist.
REMARQUE! Ne connectez pas l’appareil à l’alimentation électrique avant qu’il ne soit entièrement assemblé.
1
A
B
C D
E G I
F H J
K
L
# DESCRIPTION QTY
G iPad holder 1
H PU roller 1
I Console 1
J Accessories package 1
K Right track assembly 1
L Left track assembly 1

USER MANUAL
03
USER MANUAL
HARDWARE KIT
1
(
24
)
SCREW M8*40 - 8PCS
(
5
)
NUT M8 - 10PCS
(
25
)
SCREW M6*40 - 4PCS
(
7
)
WASHER D8*Φ16*1.5 - 6PCS
(
75
)
ALLEN WRENCH #5 - 1PCS
(
76
)
ALLEN WRENCH #4 - 1PCS
(
77
)
CROSS SPANNER - 1PCS
(
21
)
SCREW M8*65 - 2PCS

USER MANUAL
04
FIG. 01
1
ASSEMBLY INSTRUCTION
1. As shown in Figure 1, place the left slide rail assembly (L) and the right slide rail assembly (K)
on the ground, and place the rowing machine (A) on the rail as shown in the figure, so that the
hole position of the rowing machine is aligned with the hole position on the slide rail. Take out
the hexagon socket head screw M8*40(24)4PCS and nylon nut M8(14)4PCS from the parts tray,
and use the cross wrench (77) and hexagon wrench #5(75) in the parts tray to install the rowing
machine (A) and the slide rail together, and do not lock it.
K
A
L
(75)
(77)
(24)
(5)
Figure 1
2. Cut the rolling strip on the handle, hold the handle and pull it up and put it in the position shown
in Figure 2. Remove the handle rubber pad (17) from the rowing machine (A) by using the
hexagon wrench #5(75) in the parts tray and set it aside for later use.
(17)
(75)
Figure 2
A
5
24
77
75
K
L
FIG. 02
1
ASSEMBLY INSTRUCTION
1. As shown in Figure 1, place the left slide rail assembly (L) and the right slide rail assembly (K)
on the ground, and place the rowing machine (A) on the rail as shown in the figure, so that the
hole position of the rowing machine is aligned with the hole position on the slide rail. Take out
the hexagon socket head screw M8*40(24)4PCS and nylon nut M8(14)4PCS from the parts tray,
and use the cross wrench (77) and hexagon wrench #5(75) in the parts tray to install the rowing
machine (A) and the slide rail together, and do not lock it.
K
A
L
(75)
(77)
(24)
(5)
Figure 1
2. Cut the rolling strip on the handle, hold the handle and pull it up and put it in the position shown
in Figure 2. Remove the handle rubber pad (17) from the rowing machine (A) by using the
hexagon wrench #5(75) in the parts tray and set it aside for later use.
(17)
(75)
Figure 2
17
75

USER MANUAL
05
FIG. 03
1
3. As shown in Figure 3, first install the foot pedal (B) on the rail and rowing machine (A) as
shown in the figure, and use the hexagon wrench #5(75) in the parts tray to connect the handle
rubber pad (17) and hexagon socket head cap screws (18) removed in Step 2 with the hexagon
socket head screw M8*40(24)4PCS and nylon nut M8 (5)4PCS removed in the parts tray, as
shown in the figure. Use hexagon wrench #5(75) and cross wrench (77) to lock the foot pedal (B)
on the track and the whole rowing machine (A). Do not lock it. Pull the handle back and place it
on the foot pedal, and use the rubber pad (17) of the handle to limit it.
(75)
(77)
(24)
(24)
(5)
(18)
(17)
B
A
Figure 3
4. As shown in Figure 4, take out the rear connecting plate (F), lock the hexagon socket head
screw M6*40(25)4PCS in the parts plate with the hexagon wrench #4(76) in the parts plate into
the rear connecting plate (F), and lock all the unlocked screws in the previous step.
(76)
(25)
(F)
Figure 4
A
5
24
24
75
77
18
17
B
FIG. 04
1
3. As shown in Figure 3, first install the foot pedal (B) on the rail and rowing machine (A) as
shown in the figure, and use the hexagon wrench #5(75) in the parts tray to connect the handle
rubber pad (17) and hexagon socket head cap screws (18) removed in Step 2 with the hexagon
socket head screw M8*40(24)4PCS and nylon nut M8 (5)4PCS removed in the parts tray, as
shown in the figure. Use hexagon wrench #5(75) and cross wrench (77) to lock the foot pedal (B)
on the track and the whole rowing machine (A). Do not lock it. Pull the handle back and place it
on the foot pedal, and use the rubber pad (17) of the handle to limit it.
(75)
(77)
(24)
(24)
(5)
(18)
(17)
B
A
Figure 3
4. As shown in Figure 4, take out the rear connecting plate (F), lock the hexagon socket head
screw M6*40(25)4PCS in the parts plate with the hexagon wrench #4(76) in the parts plate into
the rear connecting plate (F), and lock all the unlocked screws in the previous step.
(76)
(25)
(F)
Figure 4
25
76
F

USER MANUAL
06
FIG. 05
1
5. As shown in Figure 5, remove the cushion block (38) and hexagon socket head cap screws
M6*16(39) on the track with the hexagon wrench #5(75) in the parts tray, and set them aside for
later use.
(75)
(38)
(39)
Figure 5
6. Push the seat cushion (E) into the track as shown in Figure 6.
(E)
Figure 6
75
38
39
FIG. 06
1
5. As shown in Figure 5, remove the cushion block (38) and hexagon socket head cap screws
M6*16(39) on the track with the hexagon wrench #5(75) in the parts tray, and set them aside for
later use.
(75)
(38)
(39)
Figure 5
6. Push the seat cushion (E) into the track as shown in Figure 6.
(E)
Figure 6
E

USER MANUAL
07
FIG. 07
1
7. As shown in Figure 7, re-lock the cushion block (38) and hexagon socket head cap screws
M6*16(39) removed in Step 5 into the slide rail with hexagon wrench #5(75).
(75)
(38)
(39)
Figure 7
8. Install the PU roller (H) 2PCS, nylon nut (5)2PCS, flat washer (7)8PCS and hexagon socket
head screw (21)2PCS in the parts tray, and install the PU roller (H) on the track as shown in
Figure 8 by using hexagon wrench #5(75) and cross wrench (77), and do not lock the roller too
tightly, so as to make the roller.
(75)
(77)
(21)
(7) (H)
(5)
Figure 8
75
38
39
FIG. 08
1
7. As shown in Figure 7, re-lock the cushion block (38) and hexagon socket head cap screws
M6*16(39) removed in Step 5 into the slide rail with hexagon wrench #5(75).
(75)
(38)
(39)
Figure 7
8. Install the PU roller (H) 2PCS, nylon nut (5)2PCS, flat washer (7)8PCS and hexagon socket
head screw (21)2PCS in the parts tray, and install the PU roller (H) on the track as shown in
Figure 8 by using hexagon wrench #5(75) and cross wrench (77), and do not lock the roller too
tightly, so as to make the roller.
(75)
(77)
(21)
(7) (H)
(5)
Figure 8
75
77
5 7 H
21

USER MANUAL
08
USER MANUAL
FIG. 09
1
9.
41
78
5
Figure 9
Take down the sleeve (41), spring washer (78) and nylon nut (5) shown in Figure 9 from the
rowing machine in turn, and set them aside for later use, as shown in Figure 10.
Figure 10
78
5
41
FIG. 10
1
9.
41
78
5
Figure 9
Take down the sleeve (41), spring washer (78) and nylon nut (5) shown in Figure 9 from the
rowing machine in turn, and set them aside for later use, as shown in Figure 10.
Figure 10

USER MANUAL
09
USER MANUAL
FIG. 11
1
10.
41
G
Figure 11
Take out the Ipad bracket (G), and put the spare sleeve (41) placed on one side on the Ipad
bracket (G) as shown in Figure 11, paying attention to the concentricity.
11.
Figure 12
41
G
FIG. 12
1
10.
41
G
Figure 11
Take out the Ipad bracket (G), and put the spare sleeve (41) placed on one side on the Ipad
bracket (G) as shown in Figure 11, paying attention to the concentricity.
11.
Figure 12

USER MANUAL
10
USER MANUAL
FIG. 13
1
Lock the Ipad bracket (G), sleeve (41), spring washer (78) and nylon nut (5) on the rowing
machine with the cross wrench (77) in the parts tray as shown in Figure 13. Complete the
installation of the Ipad stand (g). As shown in Figure 13.
(77)
Figure 13
12. use the cross wrench (77) in the parts tray to remove the cross pan head screw 4pcs pre-locked
on the console, then pass the N line through the arrow hole, then connect the M and N connectors,
and lock the electronic watch on the frame as shown in Figure 14.
Figure 14
13. Unplug the water tank plug (O) from the upper water tank
14. Add water as shown in Figure 15. Insert one end of the manual water pump (C) into the bucket
filled with water, and point the other end of the hose at the plug of the water tank, and pinch the
77
FIG. 14
1
Lock the Ipad bracket (G), sleeve (41), spring washer (78) and nylon nut (5) on the rowing
machine with the cross wrench (77) in the parts tray as shown in Figure 13. Complete the
installation of the Ipad stand (g). As shown in Figure 13.
(77)
Figure 13
12. use the cross wrench (77) in the parts tray to remove the cross pan head screw 4pcs pre-locked
on the console, then pass the N line through the arrow hole, then connect the M and N connectors,
and lock the electronic watch on the frame as shown in Figure 14.
Figure 14
13. Unplug the water tank plug (O) from the upper water tank
14. Add water as shown in Figure 15. Insert one end of the manual water pump (C) into the bucket
filled with water, and point the other end of the hose at the plug of the water tank, and pinch the
N
M