Vision Fitness X6200HRT User manual

Assembly
Guide
X6200HRT
FOLDING ELLIPTICAL TRAINER

1
STEP
2
STEP
4
STEP
3
STEP
5
STEP
To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order. Before proceeding, find
your new Elliptical Trainer’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be
sure to read your Owner’s Guide before using your new Elliptical Trainer. If any parts, hardware or tools are missing, please call
1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Elliptical Trainer to prevent
loosening and noise. Also, during each assembly step, ensure that ALL screws are in place and partially threaded in before
completely tightening any ONE screw.
Assembly
Guide
X6200HRT
FOLDING ELLIPTICAL TRAINER
6
STEP
OPTIONAL

17MM Wrench
Screwdriver
5MM L-Shaped Wrench
TOOLS & PARTS INCLUDED
PARTS BOX
Console Mast Boot, Qty: 1
Dual Action Link Arm Covers, Qty: 2
Dual Action Axle Covers, Qty: 2
Rear Stabilizers, Qty: 2
Pedal Support Bracket, Qty: 2
Water Bottle & Cage, Qty: 1
Heart Rate Chest Strap, Qty:1
Power Supply, Qty: 1
Color-coded Hardware Bags
Owner’s Guide
Assembly Guide
Warranty Card
6MM L-Shaped Wrench
13MM Wrench

PINK BAG
GREEN BAG
HARDWARE INCLUDED
M8x13L Screw
Quantity: 2
M20x29x1.5T
Wavy Washer
Quantity: 2
ORANGE BAG
M8x20L Screw
Quantity: 2
M8 Lock Washer
Quantity: 3
M8x55L Screw
Quantity: 3
M8x10L Screw
Quantity: 4
BLUE BAG
M5.5x10x1.2T Washer
Quantity: 2
M10 Nut
Quantity: 2
M5x10L Screw
Quantity: 2
M10x35x1.5T Washer
Quantity: 2
M10x25x1T Washer
Quantity: 4
BLACK BAG
M8x35x2T Washer
Quantity: 2
M8 Nut
Quantity: 4
M4x10L PanHead Screw
Quantity: 4
M5x10L Screw
Quantity: 2
M8x16x1.5T Washer
Quantity: 2
M25x34x2T Wavy Washer
Quantity: 2
M8x30L Screw
Quantity: 2
M15x8.5x15L Spacer
Quantity: 2
M5x10x1T Washer
Quantity: 4

5
1
STEP
1
STEP
• For ease of assembly place a block
of wood (about 1” thick) under the
rear of the frame. Slide the axle
through the rear support tube. On the
left side of the axle slide on the left
guide rail and the left stabilizer.
Secure in place with the screw
(M8x20L). On the right side of the
axle slide on the right guide rail and
the right stabilizer. Secure in place
with the screw (M8x20L). Tighten with
the 5mm Allen Wrench.
ORANGE BAG
2
STEP
• Place a teflon washer (10.5x25.1T)
on the threaded stud of the rotation
linkage.
• Place the bracket end of the pedal
arm over the rotation linkage so that
the threaded stud on the linkage
inserts through the hole on the pedal
arm bracket. Fix in place with a
teflon washer (10x25x1T) a washer
(10x35x1.5T) and nut (M10). Tighten
with the 17mm wrench.
• Place the pedal arm bracket cover
over the bracket and secure in place
with the washer (5.5x10x1.2T) and
screw (M5x10L). Tighten with the
Phillips screwdriver.
• Repeat these steps on the opposite
side.
BLUE BAG
2
STEP
Rotation
Linkage
Pedal Arm
Bracket Cover

6
3
STEP
3
STEP
• Slide the rubber boot on to the
console mast.
• Unfold the wire harness located in
the frame bracket. Wrap the wire tie
coming from the bottom of the console
mast around the end of the wire
harness. Pull the wire tie and wire
harness up through the top of the
console mast while simultaneously
sliding the mast into the frame
bracket.
• Secure the mast to the frame using
three lock washers (M8) and three
capscrews (M8x55L). Tighten with the
6mm Allen wrench.
• Slide the rubber boot down the
console mast and snap it in place
on top of the side cover.
• Remove the four screws from the
back of the console with the Phillips
screwdriver. Connect the wire harness
and Heart Rate wires to the plugs in
the back of the console. Attach the
console to the console mast with the
four screws removed at the beginning
of this step.
• Attach waterbottle cage.
PINK BAG
4
STEP
4
STEP
• Slide a wavy washer
(M20x29x1.5T) on the lower link arm
axle, which is located under the foot
plate. Slide the axle through the
bracket located on top of the pedal
arm.
• Secure the lower link arm in place
by attaching the pedal support
bracket and screw (M8x13L). Secure
the outside holes in the support
bracket to the footplate with two
screws (M8x10L). Tighten all screws
with the 5mm Allen wrench
• Repeat this same step on the
opposite side
GREEN BAG

7
5
STEP
• On the right side, slide the dual
action axle cover into place on the
axle located on the console mast.
Slide a wavy washer (M25x34x2T)
and the right dual-action arm into
place on the axle. Fix in place with
the washer (M8x35x2t) and locknut
(M8). Cover with the included nut cap.
• Make sure the spacer is in place in
the socket joint of the lower link arm.
Connect the lower link arm to the
dual-action arm with a screw
(M8x30L), washer (M8x16x1.5T),
and nut (M8). Tighten with the 6mm
Allen wrench and 13mm wrench.
• Position the link arm cover into
place over the joint of the lower link
arm and the dual action arm. Secure
the two pieces of the cover together
by inserting and tightening a screw
(M5x10L) in the front of the cover.
Connect the cover to each side of the
lower link arm with a washer (M5)
and screw (M4x10L).
• Repeat these steps on the left side.
BLACK BAG
6
STEP
OPTIONAL
5
STEP
Dual-Action
Axle Cover
Link Arm
Covers
6
STEP
• NOTE: Elliptical Trainer cannot be
folded with the child safety guards in
place.
• Line up the grooves on the child
safety guards with the screws on the
guide rails. Slide the safety guard into
place on the guide rails. Tighten the
screws with the Phillips screwdriver to
lock in place.
SAFETY GUARDS
OPTIONAL
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
2003 Vision Fitness. All Rights Reserved. 7.03 Part #Z62EP34-AG1823PRD
AG18.23PRD
REV3