Vision Fitness X1400 User manual

Assembly
Guide
X1400 AND X1500
ELLIPTICAL TRAINERS

5
STEP
1
STEP
4
STEP
3
STEP
To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order. Before proceeding, find
your new Elliptical Trainer’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be
sure to read your Owner’s Guide before using your new Elliptical Trainer.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12.
NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Elliptical Trainer to prevent loos-
ening and noise. Also, during each assembly step, ensure that ALL screws are in place and partially threaded in before completely
tightening any ONE screw.
Assembly
Guide
X1400 AND X1500
ELLIPTICAL TRAINERS
2
STEP

TOOLS & PARTS INCLUDED
Screwdriver
5mm L-Shaped Wrench
PARTS BOX
13mm Wrench
Console Mast Boot
Dual-Action Link Arm Covers
Dual-Action Axle Covers
Pedal Arm Joint Covers
Right and Left Footplates
Rear Stabilizers
Water Bottle and Cage
Power Supply (X1500 only)
Tension Knob and Bracket (X1400 only)
Color Coded Hardware Bags
Owners Manual
Assembly Guide
Warranty Card
13mm Wrench
Quantity: 1
GREEN BAG
5mm T-Shaped Wrench
M8 Nut
Quantity: 2
M8x40L Bolt
Quantity: 2
8x18x1T Washer
Quantity: 2
Q235 Knuckle Pin Quantity: 2
(located in parts box)

ORANGE BAG
PINK BAG
BLACK BAG
M8 Nut
Quantity: 4
M5x10L Screw
Quantity: 12
M8x15L Screw
Quantity: 4
8x17x1T Washer
Quantity: 4
M5x70L Screw X1400 ONLY
Quantity: 1
M8X15L Screws
Quantity: 6
5x10x1T Washer X1400 ONLY
Quantity: 1
8x16x1.5T Washer
Quantity: 2
25x34x2T Wavy Washer
Quantity: 2
8x25x1.5T Washer
Quantity: 2
M8x45L Screw
Quantity: 2
BLUE BAG
M4x12L Screw
Quantity: 2
8x38x2T Washer
Quantity: 2
4x10x1T Washer
Quantity: 2
Nylon Nut Cover
Quantity: 2
5x10x1T Washer
Quantity: 4
SS41 Link Joint Sleeve
Quantity: 2
25x34x2T Wavy Washer
Quantity: 2
M8x20L Screw
Quantity: 2
8x38x2T Washer
Quantity: 2
M4x12L Screw
Quantity: 2
Nylon Interval Ring
Quantity: 4
8x18x1T Arc Washer
Quantity: 2 SW8 Lockwashers
Quantity: 6
6x14x1T Washer
Quantity: 8

5
1
STEP ORANGE BAG
• Slide the stabilizer shaft through the
plastic sleeves in the rear support tube.
• Slide the stabilizer covers onto the
stabilizer shaft and secure with
(M8x15L) screws and (8x16x1T) flat
washers. Tighten with the 5mm
T-shaped wrench.
• Attach end caps to the end of the
guide rails with (M8x15L) screws.
Tighten with the 5mm T-shaped wrench.
1
STEP
Stabilizer
Cover
Stabilizer
Shaft
End Cap

6
2
STEP
Pedal Arm
Cover
Pedal Arm
Knuckle
Joint
Rotation
Axle
2
STEP
• Slide a wavy washer (25x34x2T) on
to the right rotation axle. Slide the
knuckle joint of the pedal arm onto the
right rotation axle. The pedal arm roller
wheel should be placed into the groove
of the guide rail. Secure the pedal arm
to the rotation axle with a washer
(8x38x2T) and screw (M8x20L).
Tighten with the 5mm T-shaped wrench.
• Place the pedal arm cover over the
knuckle joint. Secure in place with a
washer (4x10x1T) and screw
(M4x12L). Tighten with the screwdriver.
• Repeat both steps on the left side.
BLUE BAG

7
3
STEP
• With the screwdriver remove the
screws for the water bottle cage in the
center of the console mast. Slide the
rubber boot onto the console mast.
• Unfold the wire harness located in
the frame bracket. Wrap the end of
the wire tie, located at the bottom of
the console mast, around the end of
the wire harness. Pull the wire tie and
wire harness up through the console
mast while simultaneously sliding the
mast over the frame bracket.
NOTE: For the X1400 the tension
cable should also run up through the
console mast.
• Slide a lock washer (SW8) fol-
lowed by a flat washer (8x17x1T)
onto four of the screws (M8x15L).
Insert these screws through the side of
the mast to secure the mast to the
frame. Slide a lock washer (SW8) fol-
lowed by a arc washer (8x18x1T)
onto the two remaining screws
(M8x15L). Insert these screws through
the holes in front of the mast. Tighten
all screws with the 5mm T-shaped
wrench.
• Slide the rubber boot down the
console mast and snap it in place
over the side covers.
• X1400 ONLY: Snap the tension
knob mounting support onto the
tension knob. Turn the tension knob to
level 16. Connect the knob cable to
the tension cable in the console mast.
Secure the tension knob to the console
mast with the washer (5x10x1T) and
screw (M5x70L). Tighten with the
screwdriver.
• Remove the four screws from the
back of the console. Connect the wire
harness to the plug in the back of the
console. Connect the heart rate wires
into the heart rate plugs in the back of
the console. Attach the console to the
console mast with the four console
screws and screwdriver. NOTE: For
the X1400 insert 2 AA Batteries.
• Attach the water bottle cage to the
console mast with the two screws
removed earlier in this step.
PINK BAG
X1400
X1500
3
STEP
Console
Mast
Tension
Knob
Tension Knob
Bracket
Console
Boot
X1400 ONLY

8
4
STEP
• Slide the knuckle pin (Q235)
through the bushings of the knuckle.
Slide the link arm over the knuckle so
that the hole in the link arm lines up
with the hole in the knuckle pin. Insert
a bolt (M8x40L) through the hole in
the link arm and knuckle pin and
attach a washer (8x18x1T) and nylon
nut (M8) to the end of the bolt.
Tighten with the two 13mm wrenches.
• Repeat the same step on the left side.
GREEN BAG
4
STEP
Link Arm
Knuckle Pin

5
STEP
Link Arm
Covers
Dual-Action
Axle Cover
Footplate
Dual-Action
Arm
Console
Mast Axle
9
5
STEP
• Slide the dual-action axle cover into
place over the console mast axle.
Slide a wavy washer (25x34x2T)
onto the console mast axle. Slide the
right dual-action arm onto the axle. Fix
in place with a washer (8x38x2T)
and nylon nut (M8). Cover with the
included nylon nut cover.
• Insert the link joint sleeve (SS41)
into the socket joint of the right link
arm. Position the socket joint of the
link arm into the bracket at the bottom
of the dual-action arm. Position the
Nylon Interval Rings between the
socket joint and bracket on each side.
Insert a screw (M8x45L) through the
bracket, interval rings and socket joint
sleeve. Secure in place with a washer
(8x25x1.5T) and nylon nut (M8).
Tighten with the 5mm T-shaped
wrench and 13mm wrench.
• Position the link arm covers over the
socket joint and secure the two pieces
together with a screw (M4x12L).
Tighten with the screwdriver. Connect
the cover to each side of the link arm
with a washer (5x10x1T) and screw
(M5x10L). Tighten with the
screwdriver.
• Position the right footplate onto the
right link arm. Secure in place with
four washers (6x14x1T) and four
screws (M5x10L). Tighten with the
screwdriver.
• Repeat steps on the left side.
BLACK BAG

500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
©2005 Vision Fitness. All Rights Reserved. 12.05
AG18.34PRD
REV3
starts
vision
with a
it all