VISIONARY DESIGNS MOD-1222 User manual

www.classicexhibits.com
Step 1
Page 1 of 6
866.652.2100
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - MOD-1222 Kiosk Assembly
Back
Front
1
2
3
4
6
6
7
7
8
8
Infill
B
5
5
5
5
Counter Top
Item Number
1
2
3
4
5
6
7
8
Qty.
1
1
1
1
4
2
2
2
Description
37.86”h Curved Vertical Extrusion
37.86”h Curved Vertical Extrusion
37.86”h Curved Vertical Extrusion
37.86”h Curved Vertical Extrusion
17”w Horizontal Extrusion
16.375”w Curved Horizontal Extrusion
18”w Horizontal Extrusion
31.75”w Curved Horizontal Extrusion
Setup:
1) Connect horizontal extrusions [6,7,8] between curved vertical
extrusions [1,2 and 3,4] inserting infills [E,F and A,B] as shown.
2) Connect assembled front and back together with horizontal
extrusions [5] inserting side infills [C,D] as shown.
3) Set shelf on shelf pins and counter top on assembled pedestal.
Front
Shelf Pin
Shelf
Infill
A
Infill
F
Infill
E
Infill
C
Infill
D

www.classicexhibits.com
Step 2
Page 2 of 6
866.652.2100
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - MOD-1222 General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C EliateDDliateDDetail B
Detail A
Setscrews

www.classicexhibits.com
866.652.2100
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -Case Packaging
1-4
5
7
6
8
Bottom
Infills
Counter Top
Setup Hardware
Level 1 Level 2 Level 3
Top View
Level 4
Shelf
Side
Infills
Top
Infills