VISIONARY DESIGNS VK-1124 Manual

© 2015
Order #XXXXX - VK-1124 Layout
When assembled
10’
10’
SETUP INSTRUCTIONS

© 2015
Order #XXXXX -
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2015
Order #XXXXX -
Case 1 of 2
Case 1 Packing
Backwall Components
Header Components
Top View of Each Level
Level 1 (Bottom) Level 3 Level 4 Level 5Level 2
Flange Plate
Backwall
Counter
#15
#16
#14
Base Plate
Horizontal Extrusions #7a&7b and 8a&8b
#11
#1
#6
#4
#9 & #10
#2
#3
#5
#12
Graphics
Halogen Lights
Setup Hardware

© 2015
Order #XXXXX -
Step 1 of 3
When assembled
3
1
2
A
A
B
B
A
3A
1A
2A
5
6
6A
5A
7
4
4
7A
Item
1
1A
2
2A
3
3A
4
5/5A
6/6A
7/7A
Qty.
1
1
1
1
1
1
2
1/1
1/1
1/1
Description
47.9975”h Lower Curved Extrusion
38.5”h Upper Curved Extrusion
47.9975”h Lower Curved Extrusion
38.5”h Upper Curved Extrusion
47.9975”h Lower Curved Extrusion
38.5”h Upper Curved Extrusion
36.1425”h Backwall Support Extrusion
44”w Lower Horizontal Extrusion
44”w Upper Horizontal Extrusion
23”w Upper Horizontal Extrusion
Steps:
1) Connect backwall upper and lower verticals together [1] to [1A],
[2] to [2A] and [3] to [3A].
2) Connect horizontal extrusions together [5] to [5A] and [6] to [6A].
3) Attach horizontal assemblies [5/5A and 6/6A] between vertical
assemblies [1/1A] and [2/2A].
4) Attach horizontal extrusions [7 and 7A] between vertical assemblies
[2/2A and 3/3A].
5) Attach support leg extrusions [4] to back of verticals [1] and [3], see
leg attachment detail.
6) Attach graphics to backwall where indicated.
Keep assembled
when shipping
Backside of backwall
Connect support leg to vertical
by placing lock into slot and
tighten with Allen Wrench.
Support Leg Attachment
(If accidentally removed from vertical)
GREEN STAR indicates location
of connection lock with knob.
Knob
**Do not over tighten Knobs.**
RED STAR indicates location
of connection bar knob.
Turn Knob Clockwise
to Tighten Lock
**Do not over tighten Knobs.**
Knob
Knob
Connection
Bar Note: Slide connection
bar between extrusions and
tighten knobs to secure.
Velcro: Top
Edge
Velcro: Bottom
Edge
Velcro: Bottom
Edge
Velcro: Top
Edge
Velcro: Inside
Edge Velcro: Inside
Edge
Velcro: Inside
Edge
Velcro: Inside
Edge
Backwall Assembly

© 2015
Order #XXXXX -
Step 2 of 3
When assembled
Item
8
9
9A
10
11
Qty.
1
1
1
1
1
Description
Base Plate
37.476”h Vertical Extrusion
Flange Plate
15.69”w Horizontal Extrusion
18.5”w Horizontal Extrusion
Steps:
1) Attach base plate to vertical [9].
2) Connect horizontals [10] & [11] between vertical [9]
and backwalll assembly.
3) Attach counter to upper horizontal [11] using
mounting plate [9A]
Base Plate Attachment
8
9
10
11
Connect Vertical Extrusion to Base
Plate by placing lock into slot
and tighten with tool.
9A
Screw
Counter Top Attachment
Insert screws located on underside
of counter into holes on flange plate
and secure with wing nuts.
2A
Note: Extrusions [9, 10
and 11] must stay assembled
when shipping unit in case. *
Holes for
monitor mount
attachment
4
Monitor Mount
Monitor Mount
Attachment
*
Counter Assembly

© 2015
Order #XXXXX -
Step 3 of 3
Item
12/12A
13/13A
Qty.
1/1
1/1
Description
6.0257”h Vertical Extrusion
35.74”w Curved Horizontal
Steps:
1) Connect upper curved horizontals [13] & [13A] together.
2) Attach verticals [12] & [12A] to each end of
horiozntals as shown.
3) Attach header to upper backwall horizontals. When assembled
12
13
13A
12A
Velcro:
Back/Bottom
Edge
Velcro:
Back/Bottom
Edge Velcro:
Back/inside
Edge
Velcro:
Back/inside
Edge
Header Assembly