Vivo DESK-E-200B User manual

Black Electric Dual Motor Desk Frame
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-e-200b
SKU: DESK-E-200B
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual
and do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect
assembly, or inappropriate use.
WARNING!
PACKAGE CONTENTS
D(x2)
Foot
Bx2)
Motorized Leg
C(x2)
Side Bracket
A(x1)
Telescopic
Crossbar
Set
F(x12)
M6x10
Gx8)
M6x30
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC
SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
H(x16)
ST4.8x16
I(x2)
ST2.9x15
J(x1)
Power Cord
K(x1)
Control Unit
L(x1)
Control
Panel
M(x1)
Extension
Cable
N(x8)
Cable Clip
O(x1)
Allen
Wrench
Ex8)
M6x8

3
220lbs
(100kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
Loosely assemble the cross bars (A) making sure the larger holes are facing out and the locking holes
are facing up as shown below. Partially insert the M6x8 bolts (E) into the locking holes, making sure
the crossbars are still able to slide freely.
TOOLS NEEDED
Phillips
Screwdriver Drill Tape
Measure
E
A

4
STEP 2
Attach both assembled crossbars to each of the legs (B) using the M6x10 bolts (F) as shown below
making sure the locking bolts are still facing up on the crossbars. Tighten with the Allen Wrench (O).
STEP 3
B
B
F
Attach the side brackets (C) to both ends of the frame using four M6x10mm bolts (F). Tighten with the
Allen Wrench (O).
C
F

5
STEP 4
Place the feet (D) on the legs and attach them using the M6x30 bolts (G). Tighten with the
Allen Wrench (O).
STEP 5
FOR VIVO DESKTOP: Adjust the frames width until the side bracket holes line up with the predrilled
holes on the desktop. Adjust the inner crossbar section until all of the locking bolts (E) are able to
make contact, then fully tighten using the Allen wrench (O). To attach the desktop, refer to the manual
included with your desktop. Set aside x2 of the ST4.8x16 screws (H) for mounting the Control Unit (K).
FOR OTHER DESKTOP: Adjust the frame to the desired width while making sure the overhang does not
exceed 10” on either side. Adjust the inner crossbar section until all of the locking bolts (E) are able to
make contact, then fully tighten using the Allen Wrench (O). Drill holes to a depth of 3/8” (10mm) using a
1/8” or 3mm bit for the desk frame mounting holes. Secure the frame using ST4.8x16 screws (H) making
sure to set aside x2 of the ST4.8x16 screws (H) for mounting the Control Unit (K).
D
G
E
H

6
STEP 6
Attach the control panel (L) to the desktop using the ST2.9x15 screws (I) making sure the cable can
reach the control unit. Attach the Control Unit (K) to the desktop using the ST4.8x16 screws (H) making
sure one of the leg motor cables can be reached without an extension cable.
STEP 7
Connect the Power Cord (J) and the Control Panel (L) to the Control Unit (K), then connect the motor
cables from the Legs (B) to the Control Unit (K) using an extension cable (M) for one leg if needed.
Organize cables using the Cable Clips (N).
Note: A desk reset is required before use. Refer to the Controller User Guide for operational
instructions.
I
H
L
K
BB
L
K
J
M

7
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.
Do not exceed desk
weight limit.
Keep area of vertical
motion free of
obstacles.
Keep weight on desk
balanced for correct
operation and longer
life of components.
Leave enough slack in
cables to allow for full
range of vertical motion.
STEP 8
If necessary adjust the foot pads on the bottom of the feet (D) to level the desk.
D
D

LAST UPDATED: 10/06/2020
REV2
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303