Vivo DESK-E144BN User manual

Black & Vintage Brown Wood 47" x 24" Electric Desk
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-e144bn
SKU: DESK-E144BN
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage
or injury caused by improper mounting, incorrect assembly, or inappropriate use.
176lbs
(80kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
PACKAGE CONTENTS
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC
SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
A(x4)
Foot Pads
B x4)
M8x47
C(x6)
M6x10
D(x8)
M6x35
E(x6)
M6x12
F (x40)
M5x16
G x1)
5mm Allen
Wrench
I (x1)
4mm Allen
Wrench
J(x13)
Wood Dowel
Pin
H x1)
2mm Allen
Wrench
K(x2)
Cable Clip
L (x20)
Anti-vibration
Pad
1 x1)
Desktop
2(x1)
Le Crossbar
3(x1)
Right Crossbar
4(x1)
Leg
5 (x1)
Leg with Motor
6 x1)
Sync Rod
7(x2)
Feet
8(x2)
Side Bracket
9(x4)
Connector
10 (x1)
Crossbar
Connector
11 (x1)
Control Panel
12 (x1)
AC Adapter

3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
Phillips
Screwdriver
Drill
Level
Assemble the Le and Right Crossbars (2, 3) to the Legs (4, 5) using M8x47 bolts (B) and tighten with
the 5mm Allen Wrench (G). Make sure tabs on either crossbar are facing out as shown below.
G
10
2
3
11
6
4
8
9
8
5
7
7
1
12

4
STEP 2
STEP 3
Place the Side Brackets (8) on the legs as shown, then insert and tighten M6x10 bolts (C) using the
4mm Allen Wrench (I).
Assemble the side brackets (5) to the legs using M6x10 bolts (B) and tighten with the 4mm Allen
wrench (E). Insert the anti-vibration pads (H) into the desktop mounting holes in the crossbar and side
brackets.
I
Assemble Le and Right Crossbars (2, 3) using Crossbar Connector (10) and M6x12 bolts (E) and 4mm
Allen Wrench (I). Crossbars must be assembled to outer spacing, with a 4.3" (10.9cm) center gap. Place
the feet (7) on the legs as shown, then insert and tighten M6x35 bolts (D) using the 5mm Allen Wrench
(G). Screw the Foot Pads (A) into the feet.
C
S=5mm
G
DE
A
I

5
STEP 4
STEP 5
Insert the Sync Rod (6) into the non-motorized Leg (4). Loosen the knob on the sync rod, then extend
the rod onto the Leg with Motor (5) and tighten the knob. Tighten the set screw on the end of the sync
rod using the 2mm Allen Wrench (H). Insert the Anti-vibration pads (L) into the desktop mounting
holes in the crossbar and side brackets.
Insert Wood Dowel Pins (J) into the predrilled holes on the edges of Desktop (1) and connect all
sections together. Fit center sections together first, then add the sides. Once assembled, attach
Connectors (9) with M5x16 screws (F) and a Phillips screwdriver.
H
L
L
H
F
J

6
STEP 6
STEP 7
Carefully place assembled desk frame upside down ontop of assembled Desktop (1). Secure the frame
to the desktop using M5x16 screws (F) and a Phillips screwdriver.
Mount the control panel (11) to the desktop (1) using M5x16 screws (F) with a Phillips screwdriver.
Connect the AC adapter (12) and motor to the control panel. Organize cables using the cable clips (K).
F
K
F

7
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.
Do not exceed desk
weight limit.
Keep area of vertical
motion free of
obstacles.
Keep weight on desk
balanced for correct
operation and longer
life of components.
Leave enough slack in
cables to allow for full
range of vertical motion.
STEP 8
Carefully turn the desk right side up and connect the AC adapter (12) to a wall outlet. If necessary, adjust
foot pads (A) to level the desk. The desk is now ready for use. Please refer to the Controller User Guide
for operating instructions.

LAST UPDATED: 06/28/2021
REV1.3
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr