Vivo STAND-TV70B User manual

Black V-Base Studio TV Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-tv70b
SKU: STAND-TV70B
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Leg
B(x1)
Pole
C(x2)
Foot
D (x1)
Upper VESA
Bracket
E (x1)
Lower VESA
Bracket
F (x2)
Foot Pad
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call
a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation
may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting,
incorrect assembly or inappropriate use.
NOTE: SOME HARDWARE MAY NOT BE USED
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
P-A (x1)
Steel Cable
P-B (x2)
Security
Clip
P-C (x2)
Security Cable
Clamp
S-A x4)
M8x12mm
Screw
S-B (x4)
M6x15mm
Screw
G (x2)
Cable Cover
T-A (x1)
4mm Allen
Wrench
P-D (x1)
2mm Allen
Wrench
T-B x1)
5mm Allen
Wrench
P-E (x4)
ST4.8x38mm
Screw
P-F (x4)
Anchor
M-A (x4)
M6x14mm
Screw
M-B (x4)
M8x16mm
Screw
M-C (x4)
M6x30mm
Screw
M-D (x4)
M8x35mm
Screw
M-E (x4)
M8 Washer
M-F (x4)
5mm Spacer
M-G (x4)
15mm Spacer
P-G(x2)
M5 Washer

3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
Phillips
Screwdriver
88lbs
Slide the Feet (C) onto the base of the Leg (A). Insert M8x12mm Screws (S-A) into the
bottom holes of the feet. Tighten with the 5mm Allen Wrench (T-B). Insert M6x15mm
Screws (S-B) through the base into the rear holes of the feet. Tighten with the 5mm Allen
Wrench (T-B). Screw the Foot Pads (F) into the base, and adjust foot pads to sit level on
the floor.
Tape
Measure
DO NOT EXCEED
WEIGHT CAPACITY.
Failure to do so may
result in serious injury.
88lbs
(40kg)
Drill Pencil Stud Finder
Screw the Foot Pads (F) into the base, and adjust foot pads to sit level on the floor.
CA
S-A
S-B
T-B
T-B
F

4
STEP 2
Screw Pole (B) onto Leg (A). Loosen the set screws in Collar (B1) using the 4mm Allen
Wrench (T-A). Adjust height of Collar (B1) to the recommended position below the top
of the pole based on your TV’s VESA mounting hole pattern. Tighten the set screws,
making sure they face towards the back of the stand.
Note: Ensure collar is securely
locked before mounting TV.
B1
T-A
T-A

5
STEP 3
Remove Screw (E1) from the lower VESA Bracket (E) and open the clamp.
STEP 4
OPTION A: Flat Back TV
Position Upper VESA Bracket (D) over top holes on TV and secure with Screws
(M-A or M-B), M8 Washers (M-E) and Security Clips (P-B). Position Lower VESA
Bracket (E) on the bottom holes and secure using Screws (M-A or M-B) and M8
Washers (M-E).
OPTION B: Curved Back TV
Position Upper VESA Bracket (D) over top holes on TV and secure with Screws
(M-A or M-B), M8 Washers (M-E) and Security Clips (P-B). Position Lower VESA
Bracket (E) on the bottom holes and secure using Screws (M-A or M-B) and M8
Washers (M-E).
E1
E
E

6
STEP 5
Slide the TV onto assembled stand. Close the clamp on the Lower VESA Bracket
(E) over the pole and secure with previously removed Screw (E1).
E

7
STEP 6
Route cables through the cables holes in the Leg (A). Install Cable Covers (G) to the
cables holes, using pliers to break out sections for x2 or x3 cables if needed.
G
A

8
Anchor TV Stand
OPTION A: Wood Wall Installation
Using Security Cable Clamps (P-C) as guides, mark drilling locations on the wall.
Use of a stud finder is recommended. Drill holes at least 1.6” (40mm) deep using a
1/8” (3.5mm) drill bit.

9
Anchor TV Stand (continued)
Mount Clamps (P-C) to the wall using ST4.8 x38mm Screws (P-E).
Thread Steel Cable (P-A) through the Security Clips (P-B) on the TV and center holes in
the Cable Clamps as shown, then tighten clamps using the 2mm Allen Wrench (P-C).
P-C

10
OPTION B: Concrete/Brick Wall Installation
Using Security Cable Clamps (P-C) as guides, mark drilling locations on the wall.
Drill holes at least 1.6” (40mm) deep using a 9/32” (7mm) drill bit.
Anchor TV Stand (continued)