Vivo STAND-TV07A User manual

Dark Walnut Tabletop TV Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-tv07a
SKU: STAND-TV07A
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Base
B(x1)
Right Foot
C(x1)
Le Foot
D (x1)
Upper VESA Bracket
E (x1)
Lower VESA Bracket
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
P-E (x1)
ST4.8x38mm Screw
P-F (x1)
Anchor
P-G (x2)
M5 Washer
F x1)
Pad
G (x6)
Round Pad
S-A (x4)
M6x18mm Screw
P-A (x1)
Security Cable
P-C (x1)
Security Bracket
P-D (x2)
Security Cable
Clamp
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
88lbs
(40kg)
P-B (x2)
Security Clip
T-A (x1)
4mm Allen Wrench
M-B (x4)
M6x14mm Screw
M-C (x4)
M6x30mm Screw
M-D (x4)
M8x30mm Screw
M-A (x4)
M5x14mm Screw
M-E (x4)
M8x50mm Screw
M-G (x8)
Small Spacer
M-H(x8)
Large Spacer
M-F (x4)
M5-M8

3
ASSEMBLY STEPS
STEP 1
Assemble Right Foot (B) and Le Foot (C) to Base (A) using M6x18mm Screws (S-A) and 4mm Allen
Wrench (T-A).
STEP 2
Remove adhesive backing from Pad (F) and Round Pads (G) and appply them to Right Foot (B) and Le
Foot (C).
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO
MOUNT. We include mounting hardware for brick and concrete walls. If unsure, please contact us at
vivo-us.com, email at [email protected]om, or call us at 309-278-5303.
TOOLS NEEDED
Phillips
Screwdriver Drill Tape Measure Level Pencil
B
A
C
S-A
T-A
F
G
B
C

4
STEP 3
Loosen the collar on Base (A) using 4mm Allen Wrench (T-A). Adjust the collar to the desired height,
and tighten with 4mm Allen Wrench (T-A).
NOTE: The recommended height for the collar is between 50-150mm (2”-5.9”) from the top of Base (A).
STEP 4
Remove the Security Screw (E1) from Lower VESA Bracket (E) and open the clamp.
T-A
A
Collar
E1
E

5
STEP 5
OPTION A: Flat Back Monitor
Position VESA brackets horizontally on the back of the TV, making sure Upper VESA Bracket (D) is on
top and Lower VESA Bracket (E) is below. Secure using screws (M-A or M-B) with Square Washers (M-F)
and M5 Washers (P-G) and Security Clips (P-B) installed to top holes.
OPTION B: Curved Back Monitor
Position VESA brackets horizontally on the back of the TV, making sure Upper VESA Bracket (D) is
on top and Lower VESA Bracket (E) is below. Secure using screws (M-C, M-D or M-E) with Square
Washers (M-F) and Spacers (M-G, M-H) with Security Clips (P-B) installed to top holes.
P-G
P-B
E
P-B
P-B P-B
E

6
STEP 6
Slide the TV with VESA Brackets (D, E) onto Base (A). Rest Upper VESA Bracket (D) on the collar of Base
(A). Close the clamp on Lower VESA Bracket (E) over the pole and secure with the previously removed
Security Screw (E1). Using 4mm Allen Wrench (T-A), remove the cable management cover from the
back of Base (A) and route cables.
STEP 7 (Option A)
Wood Stud Wall
Using Security Bracket (P-C) as a guide, mark the drilling location on the wall at the same height as
Upper VESA Bracket (D). Use of a stud finder is recommended. Drill the hole at least 40mm (1.6”) deep
using a 3.5mm (1/8”) drill bit.
P-C

7
Wood Stud Wall
Mount Security Bracket (P-C) to the wall usinig ST4.8x38mm Screw (P-E).
STEP 7 (Option A Continued)
STEP 7 (Option B)
Concrete/Brick Wall
Using Security Bracket (P-C) as a guide, mark the drilling location on the wall at the same height as
Upper VESA Bracket (D). Drill the hole at least 40mm (1.6”) deep using a 7mm (9/32”) drill bit. Mount
Security Bracket (P-C) to the wall using Anchor (P-F) and ST4.8x38mm Screw (P-E).
STEP 8
Thread Security Cable (P-A) through Security Clips (P-B)
on TV and center hole in Security Bracket (P-C) as shown,
then tighten Security Cable Clamps (P-D) using a Phillips
screwdriver.
P-E
P-C
P-C
P-A
P-B
P-C
P-D

LAST UPDATED: 07/21/2022
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303