VWR Standard Series User manual

Instruction Manual
Standard Orbital Shaker
Advanced Orbital Shaker

1
Package contents
Orbital or Reciprocating Shaker
Non-skid rubber mat,
92” (234cm) detachable power cord
Instruction manual
Warranty
Manufacturer warrants this product to be free from defects in material and workmanship
when used under normal conditions for five (5) years. Register your equipment or
instrument online at www.vwr.com/warranty for US residents or www.vwrcanlab.com/
warranty for Canadian residents. For your reference, make a note of the serial num-
ber, date of purchase and supplier here.
Serial Number: _______________________________________________________
Date of Purchase: ____________________________________________________
Supplier: ____________________________________________________________
table of contents
Package Contents . . . . . . . . . . . . . . . 1
Warranty . . . . . . . . . . . . . . . 1
Installation . . . . . . . . . . . . . . . 2
Maintenance & Servicing . . . . . . . . . . . . . . . 2
Intended Use . . . . . . . . . . . . . . . 2
Environmental Conditions . . . . . . . . . . . . . . . 3
Equipment Disposal . . . . . . . . . . . . . . . 3
Safety Instructions . . . . . . . . . . . . . . . 4
Standards & Regulations . . . . . . . . . . . . . . . 4
Specifications . . . . . . . . . . . . . . . 5-6
Operating Instructions . . . . . . . . . . . . . . . 7-10
Troubleshooting . . . . . . . . . . . . . . . 11
Replacement Parts . . . . . . . . . . . . . . . 12-17
Accessories . . . . . . . . . . . . . . . 18-22

2
Upon receiving the VWR Orbital or Reciprocating Shaker, check to ensure that no
damage has occurred during shipment. It is important that any damage that occurred
in transport is detected at the time of unpacking. If you do find such damage the carrier
must be notified immediately.
After unpacking, place the shaker on a level bench or table, away from explosive
vapors. Ensure that the surface on which the unit is placed will withstand typical heat
produced by the unit and place the unit a minimum of six (6) inches from vertical
surfaces. Always place the unit on a sturdy work surface.
The Orbital or Reciprocating Shaker is supplied with a power cord that is inserted into
the IEC connector on the back of the unit first, then it can be plugged into a properly
grounded outlet. The 120V unit plugs into a 120 volt, 50/60 Hz source. The 230V unit
plugs into a 230 volt, 50/60 Hz source.
Maintenance & servicing
The Orbital or Reciprocating Shaker is built for long, trouble-free, dependable service.
No lubrication or other technical user maintenance is required. It needs no user
maintenance beyond keeping the surfaces clean. However at least every three (3)
months you should:
• Unplug the unit.
• Remove any accumulated dirt from the base and tray.
• Check all accessible items to make sure they are properly tightened.
The unit should be given the care normally required for any electrical appliance. Avoid
wetting or unnecessary exposure to fumes. DO NOT use a cleaning agent or solvent
on the front panel which is abrasive or harmful to plastics, nor one which is flammable.
Always ensure the power is disconnected from the unit prior to any cleaning. If the unit
ever requires service, contact your VWR representative.
These Shakers are intended for general laboratory use.
Operating Conditions: Indoor use only.
installation intended Use

*For use in CO2 environments, incubators, or cold rooms.
Temperature: 0 to 40°C (32 to 104°F)
Humidity: maximum 80% relative humidity, non-condensing
Altitude: 0 to 6,562 ft (2000 M) above sea level
Non-Operating Storage:
Temperature: -20 to 65°C (-4 to 149°F)
Humidity: maximum 80% relative humidity, non-condensing
Installation Category II and Pollution Degree 2 in accordance with IEC 664.
environMental conditions - advanced & reciProcating
Operating Conditions: Indoor use only.
*For use in CO2 environments, incubators, or cold rooms.
Temperature: -10 to 60°C (14 to 140°F)
Temperature: -10 to 40°C (14 to 104°F) (Model 1000 Advanced)
Humidity: maximum 80% relative humidity, non-condensing
Altitude: 0 to 6,562 ft (2000 M) above sea level
Mains supply voltage: Fluctuations are not to exceed 10 percent of the nominal
supply voltage.
Non-Operating Storage:
Temperature: -20 to 65°C (-4 to 149°F)
Humidity: maximum 80% relative humidity, non-condensing
Installation Category II and Pollution Degree 2 in accordance with IEC 664.
*Avoid cold starts: Unit is not designed to start after being in a cold room environment.
Bring unit into cold room from a room temperature environment, operate and remove
unit from cold room as soon as operation is complete.
environMental conditions - standard
This equipment must not be disposed of with unsorted waste. It is your responsibility to
correctly dispose of the equipment at life-cycle-end by handing it over
to an authorized facility for separate collection and recycling. It is also
your responsibility to decontaminate the equipment in case of biological,
chemical and/or radiological contamination, so as to protect the persons
involved in the disposal and recycling of the equipment from health
hazards.
For more information about where you can drop off your waste of equipment, please
contact your local dealer from whom you originally purchased this equipment. By doing
so, you will help to conserve natural and environmental resources and you will ensure that
your equipment is recycled in a manner that protects human health.
eqUiPMent disPosal
3

4
Please read the entire instruction manual before operating the Orbital Shaker.
WARNING! DO NOT use the Orbital Shaker in a hazardous atmosphere or with
hazardous materials for which the unit was not designed. Also, the user should
be aware that the protection provided by the equipment may be impaired if used
with accessories not provided or recommended by the manufacturer, or used in a
manner not specified by the manufacturer.
Always operate unit on a level surface for best performance and maximum safety.
DO NOT lift the unit by the tray.
CAUTION! To avoid electrical shock, completely cut off power to the unit by dis-
connecting the power cord from the unit or unplug from the wall outlet. Disconnect
unit from the power supply prior to maintenance and servicing.
Spills should be removed promptly. DO NOT immerse the unit for cleaning.
DO NOT operate the unit if it shows signs of electrical or mechanical damage.
Earth Ground - Protective Conductor Terminal
Alternating Current
Pinch Point - Keep fingers clear during operation.
VWR hereby declares under its sole responsibility that the construction of this product
conforms in accordance with the following standards:
Safety standards:
EN 61010
EN 61010-2-051
CAN/CSA C22.2 No. 61010-1-04
UL 61010-1
EMC standards:
CISPR 11 IEC 61000-4-3
IEC 61326 IEC 61000-4-4
IEC 6100-3-2 IEC 61000-4-5
IEC 6100-3-3 IEC 61000-4-6
IEC 61000-4-2 IEC 61000-4-11
Associated EU guidelines:
EMC directive 2004/108/EC
LVD directive 2006/95/EC
ROHS directive 2011/65/EU
safety instrUctions standards & regUlations

Troemner, LLC déclare par la présente sous sa seule responsabilité que la conception
de ce produit répond aux exigences des normes suivantes:
Normes de sécurité:
EN 61010
EN 61010-2-051
CAN/CSA C22.2 No. 61010-1-04
UL 61010-1
Normes CEM:
CISPR 11 IEC 61000-4-3
IEC 61326 IEC 61000-4-4
IEC 6100-3-2 IEC 61000-4-5
IEC 6100-3-3 IEC 61000-4-6
IEC 61000-4-2 IEC 61000-4-11
de I’UE directives:
Directive EMC 2004/108/EC
Directive LVD 2006/95/EC
ROHS directive 2011/65/EU
S’il vous plaît lire l’intégralité du manuel d’instructions avant de faire fonctionner l’agitateur
orbital.
AVERTISSEMENT! N’UTILISEZ PAS utiliser le secoueur orbital dans un
milie u dangereux ou en présence de matières dangereuses non conformes
à la conception de l’appareil. L’utilisateur doit également être conscient que
laprotection assurée par l’équipement peut être amoindrie en cas d’utilisation
avec tout accessoire autre que ceux fournis ou recommandés par le fabricant
ou en cas d’utilisation contraire aux spécifications du fabricant.Utilisez toujours le
dispositif sur une surface à niveau pour optimiser non seulement la performance mais
la sécurité.
Toujours utiliser l’appareil sur une surface nivelée pour assurer une performance
optimale et un maximum de sécurité.
NE PAS soulever l’appareil en le tenant par le plateau.
MISE EN GARDE! Pour éviter les électrocutions, couper complètement
l’alimentation électrique de l’appareil en débranchant le cordon d’alimentation de
l’appareil ou de la prise murale. Déconnecter l’appareil de la source d’alimentation
électrique avant de procéder à tout entretien ou réparation.
Essuyer immédiatement tout liquide renversé par accident.
NE PAS immerger l’appareil en vue de son nettoyage.
NE PAS utiliser l’appareil en présence de tout signe de dommage électrique ou
mécanique.
Mise à la terre - Borne du conducteur de protection
Courant alternatif
Point de pincement – garder les doigts à l’écart de l’appareil pendant
l’utilisation.
consignes de sécUrité norMes et régleMentations
5

sPecifications
MODEL 1000
Overall dimensions LxWxH 11 x 17 x 4” (27.9 x 43.2 x 10.2cm)
Tray dimensions LxW 8.75 x 11.75” (22.2 x 29.8)
Electrical 120 volts: 5 amps, 25 watts
230 volts: 2.5 amps, 25 watts
Fuses 5mm x 20mm, 5 amp quick acting
Speed Range 40 to 300 rpm
Speed Accuracy Advanced:
Above 100rpm ±2% of set speed
Below 100rpm ±2rpm
Orbit 0.6” (15 mm)
Capacity 8 lbs (3.6kg)
Controls Standard: See page 6
Advanced: See page 8
Ship Weight 25 lbs (11.3kg)
MODEL 3500
Overall dimensions LxWxH 16.25 x 14 x 5.75 “ (41.3 x 35.6 x 14.6 cm)
Tray dimensions LxW 13 x 11” (33 x 22.2cm)
Electrical 120 volts: 5 amps, 75 watts
230 volts: 2.5 amps, 75 watts
Fuses 5mm x 20mm, 5 amp quick acting
Speed Range Advanced: 15 to 500 rpm
Standard: 25 to 500 rpm
Speed Accuracy Advanced:
Above 100rpm ±1% of set speed
Below 100rpm ±1rpm
Orbit 0.75” (19mm)
Capacity ~35 lbs (16kg) @ 75 rpm
~5 lbs (2.3kg) @ 500 rpm
Timer Advanced: 1 second to 160 hours
Standard:1 to 120 minutes
Controls Advanced: See page 8
Standard: See page 6
Ship Weight 49 lbs (22.2 kg)
MODEL 3750
Overall dimensions LxWxH 16.25 x 14 x 5.75” (41.3 x 35.6 x 14.6 cm)
Tray dimensions LxW 13 x 11” (33 x 22.2cm)
Electrical 120 volts: 5 amps, 40 watts
230 volts: 2.5 amps, 40 watts
Fuses 5mm x 20mm, 5 amp quick acting
Speed Range 20 to 300 rpm
Speed Accuracy
Above 100rpm ±1% of set speed
Below 100rpm ±1rpm
Orbit 0.75” (19mm) Total Travel
Capacity ~15 lbs @ 300 rpm
Timer 1 second to 160 hours
Controls See page 8
Ship Weight 49 lbs (22.2 kg)
MODEL 5000
Overall dimensions LxWxH 23.6 x 26.7 x 6.0” (59.9 x 67.8 x 15.2 cm)
Tray dimensions LxW 18 x 24” (45.7 x 70 cm)
Electrical 120 volts: 5 amps, 75 watts
230 volts: 2.5 amps, 75 watts
Fuses 5mm x 20mm, 5 amp quick acting
Speed Range Advanced: 20 to 500 rpm
Standard: 25 to 500 rpm
Speed Accuracy Advanced:
Above 100rpm ±1% of set speed
Below 100rpm ±1rpm
Orbit 1” (25.4 mm)
Capacity ~50 lbs @ 125 rpm
~10 lbs @ 500 rpm
Timer Advanced: 1 second to 160 hours
Standard: 1 to 120 minutes
Controls Advanced: See page 8
Standard: See page 6
Ship Weight 109 lbs
6

MODEL 10000
Overall dimensions LxWxH 28.25 x 26.7 x 7.0” (71.8 x 67.8 x 17.8 cm)
Tray dimensions LxW 24 x 24” (70 x 70cm)
Electrical 120 volts: 5 amps, 80 watts
230 volts: 2.5 amps, 80 watts
Fuses 5mm x 20mm, 5 amp quick acting
Speed Range 10000-1 = 15 to 500 rpm
10000-2 = 15 to 300 rpm
Speed Accuracy
Above 100rpm ±1% of set speed
Below 100rpm ±1rpm
Orbit 10000-1 = 1”
10000-2 = 2”
Capacity ~100 lbs @ 100 rpm *
~40 lbs @ 300 rpm
Timer 1 second to 160 hours
Controls See page 8
Ship Weight 200 lbs
MODEL 15000
Overall dimensions LxWxH 28.25 x 26.7 x 7.0” (71.8 x 67.8 x 17.8 cm)
Tray dimensions LxW 24 x 36” (70 x 91.4cm)
Electrical 120 volts: 5 amps, 80 watts
230 volts: 2.5 amps, 80 watts
Fuses 5mm x 20mm, 5 amp quick acting
Speed Range 15000-1 = 15 to 500 rpm
15000-2 = 15 to 300 rpm
Speed Accuracy
Above 100rpm ±1% of set speed
Below 100rpm ±1rpm
Orbit 15000-1 = 1”
15000-2 = 2”
Capacity ~150 lbs @ 100 rpm *
~40 lbs @ 300 rpm
Timer 1 second to 160 hours
Controls See page 8
Ship Weight 230 lbs
sPecifications cont’dstandard orbital shaker
*With optional platform and ask clamp
speed knob
time knob rocker switch
7

2. Setting speed:
a. To run in continuous mode, push rocker to the run position. Set speed knob to
desired setting and adjust if necessary. Unit will run until you move the rocker
switch to the standby position. The microprocessor speed control slowly ramps
to set speed to avoid splashing.
3. Setting time:
a. To run in timed mode, set timer and the speed knob to the desired settings.
Press the rocker switch to the time position and release. The shaker will now
run for the set time. b. To exit the timed mode turn the time knob to the extreme
counter-clockwise position.
4. Turning unit off:
a. To stop shaking function, turn the speed knob to the extreme counter clockwise
position and push the rocker switch to the standby position. The shaker should be
kept in the standby position when not in use. To completely cut off power to the
unit, disconnect the power cord from the unit or unplug from the wall outlet.
OPERATING TIPS
Centering your sample and even weight distribution on the tray helps with balance
and stability. As a safety feature, a built-in program will shut power off to the motor if
the tray is prevented from rotating, or the unit is overloaded beyond its recommended
weight capacity. To reset the unit, press the rocker switch to standby and then press
the rocker switch to the on position. The shaker will automatically restart after a power
interruption. Built-in memory maintains the last used speed and time settings during
a power interruption.
standard orbital shaker oPerating instrUctions
The Standard Orbital Shaker is used for general laboratory shaking needs.
MODEL 1000
1. Getting ready:
a. The speed knob should be at their extreme counter-clockwise position or at the
#1 on the dial.
b. Make sure the rocker switch is in the off position.
c. Plug the cord into a properly grounded outlet.
2. Setting speed:
a. To run push rocker to the on or position. Set speed knob to desired setting
and adjust if necessary. Unit will run until you move the rocker switch to the off
position. The microprocessor speed control slowly ramps to set speed to avoid
splashing.
3. Turning unit off:
a. To stop shaking function, turn the speed knob to the extreme counter-clockwise
position and push the rocker switch to the standby position. The shaker should
be kept in the standby position when not in use. To completely cut off power to
the unit, disconnect the power cord from the unit or unplug from the wall outlet.
OPERATING TIPS
Centering your sample and even weight distribution on the tray helps with balance
and stability.
The shaker will automatically restart after a power interruption.
MODEL 3500 AND 5000
1. Getting ready:
a. The speed and time knobs have a built in on-off switch at their extreme counter-
clockwise position. Turn both knobs to the off position.
b. Make sure the rocker switch is in the standby position.
c. Plug the cord into a properly grounded outlet.
8

The front panel of the Advanced Orbital Shaker contains all the controls and displays
needed to operate the unit.
A. Standby button/standby indicator light: The standby indicator light will illu-
minate when the unit is plugged in. The unit will be in standby mode. Press the
standby button to start the speed and time functions. The standby indicator light will
shut off. Press the standby button again and the unit will once again be in standby
mode.
B. Speed display: Displays the speed of the shaker.
C. Up/down arrows: For set-point control. On/off button starts/stops shaking
function.
D. Time display: Displays accumulated time (continuous mode) or how much time is
remaining (timed mode). The display range is from 0 to 9,999 minutes in one (1)
second increments. The display will indicate minutes and seconds until the timer
reaches 99 minutes and 59 seconds (99:59), then the display will automatically
display minutes up to 9,999.
E. Up/down arrows for setpoint control. On/off button starts/stops the timer function.
control Panel - advanced orbital shaker
9
A
B
C
D
E