WAGO 753-1630 User manual

Pos: 2 /Dokumentation al lgemein/Einband/Ei nband Handbuch - Frontseit e 2017 - mit DocVariablen ( Standard) @ 28\mod_1486477 502910_0.doc x@ 405388 @ @ 1
Manual
753-1630
SMI
Master Module 230 V AC
Version 1.2.0 FW/HW Version 02/01
Pos:3 /Alle Seri en (Allgemeine Module) /Rechtliches, Allg emeines/Impressum für Standardhandbücher - allg. Angaben, Anschr iften, Telefonnummern und E-Mail-Adressen @ 3\mod _1219151118203_21.doc x @ 21060 @ @1

2
753-1630 SMI Master Module 230 V AC
Manual
Version 1.2.0 FW/HW Version 02/01
© 2018 WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [email protected]
Web: http://www.wago.com
Technical Support
Phone: [phone] – 4 45 55
Fax: [phone] – 84 45 55
E-Mail: [email protected]
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail: [email protected]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH.
=== Ende der Liste für Textmarke Ei nband_vorne ===

Table of Contents 3
753-1630 SMI Master Module 230 V AC
Manual
Version 1.2.0 FW/HW Version 02/01
Pos: 5 /Dokumentation al lgemein/Verzeic hnisse/Inhalts verzeichnis - Überschrif t oG und Verzeic hnis @ 3\mod_1219 151230875_21.docx @ 21063 @ @ 1
Table of Contents
1Notes about this Documentation ..............................................................5
1.1 Validity of this Documentation..................................................................5
1.2 Copyright..................................................................................................5
1.3 Symbols ...................................................................................................6
1.4 Number Notation......................................................................................8
1.5 Font Conventions.....................................................................................8
2Important Notes ..........................................................................................9
2.1 Legal Bases .............................................................................................9
2.1.1 Subject to Changes.............................................................................9
2.1.2 Personnel Qualifications......................................................................9
2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with Underlying
Provisions............................................................................................9
2.1.4 Technical Condition of Specified Devices .........................................10
2.1.4.1 Disposal........................................................................................10
2.2 Safety Advice (Precautions)...................................................................11
3Device Description ...................................................................................13
3.1 View .......................................................................................................16
3.2 Connectors.............................................................................................17
3.2.1 Data Contacts/Local Bus...................................................................17
3.2.2 Power Jumper Contacts/Field Supply ...............................................18
3.2.3 CAGE CLAMP®Connectors..............................................................19
3.2.4 Function Earth...................................................................................19
3.3 Display Elements ...................................................................................20
3.4 Schematic Diagram................................................................................21
3.5 Technical Data.......................................................................................22
3.5.1 Device Data.......................................................................................22
3.5.2 Power Supply ....................................................................................22
3.5.3 Communication .................................................................................23
3.5.4 Climatic Environmental Conditions....................................................24
3.6 Approvals...............................................................................................25
3.7 Standards and Guidelines......................................................................26
4Function Description................................................................................27
4.1 Fieldbus Coupler Mode..........................................................................27
4.1.1 Digital Input .......................................................................................28
4.1.2 1-Button Operation/Construction Site Mode......................................28
4.1.3 Forced Position .................................................................................29
4.1.4 2-Button Operation............................................................................29
4.1.5 Positioning Curtains and Slats ..........................................................30
4.1.6 Controller Locking .............................................................................32
4.1.7 Energy Saving Mode.........................................................................32
4.1.7.1 Activating the Energy Saving Function via Timeout .....................32
4.1.7.2 Activating the Energy Saving Function via Control Byte C1.........33
4.1.7.3 Digital Output................................................................................33
4.1.8 Local Bus Failure Monitoring.............................................................34
4.1.9 Controller Failure Monitoring.............................................................34

4 Table of Contents
753-1630 SMI Master Module 230 V AC
Manual
Version 1.2.0 FW/HW Version 02/01
4.1.10 Power Failure Monitoring ..................................................................34
4.1.11 Automatic Addressing .......................................................................35
4.1.12 Auto-Replace ....................................................................................35
4.2 Full Mode ...............................................................................................37
4.2.1 System Extensions............................................................................37
4.2.2 Switching Addresses and Readdressing...........................................37
4.2.3 Logging .............................................................................................38
4.2.4 Reading the System Image...............................................................38
4.2.5 Extended SMI Command Set............................................................38
5Process Image ..........................................................................................39
5.1 Control/Status Byte................................................................................40
5.2 Extended Control/Status Byte................................................................41
5.3 Fieldbus Coupler Mode..........................................................................42
5.3.1 Output and Input Process Image.......................................................42
5.3.2 Addressing SMI Drives......................................................................43
5.3.3 SMI Commands ................................................................................44
5.4 Full Mode ...............................................................................................46
6Mounting ...................................................................................................47
6.1 Mounting Sequence...............................................................................47
6.2 Inserting and Removing Devices ...........................................................49
6.2.1 Inserting the I/O Module....................................................................49
6.2.2 Removing the I/O Module..................................................................50
6.3 I/O Modules with Pluggable Wiring Level (Series 753)..........................51
6.3.1 Coding...............................................................................................52
6.3.2 Plug Removal....................................................................................54
7Connect Devices.......................................................................................55
7.1 Connecting a Conductor to the CAGE CLAMP®....................................55
7.2 Connection Examples............................................................................56
8Commissioning.........................................................................................57
8.1 Preparation ............................................................................................57
8.2 Configuration and Parameterization ......................................................58
8.2.1 IEC Function Block Library CODESYS 2.3 .......................................58
8.2.2 e!COCKPIT .......................................................................................58
8.2.3 WAGO SMI Configurator...................................................................59
9Diagnostics ...............................................................................................60
List of Figures ....................................................................................................62
List of Tables......................................................................................................63
=== Ende der Liste für Textmarke Verzeic hnis_vorne ===

Notes about this Documentation 5
753-1630 SMI Master Module 230 V AC
Manual
Version 1.2.0 FW/HW Version 02/01
Pos: 7 /Alle Serien (Al lgemeine Module)/Über schriften/Ebene 1/ Hinweise zu dieser Dokumen tation - Überschrif t 1 @ 4\mod_1237987661750_21.d ocx @ 29029 @ 1 @ 1
1 Notes about this Documentation
Pos: 8 /Alle Serien (Al lgemeine Module)/Si cherheits- und sonstige Hin weise/Hinweis/Hin weis: Dokumentation auf bewahren @ 4\mod_123798733981 2_21.docx @ 29026 @ @ 1
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation
is included, if necessary.
Pos:9 /Alle Seri en (Allgemeine Module) /Überschrif ten/Ebene 2/Gültigkeits bereich - Überschrif t 2 @ 12\mod_1338912448776_21. docx @ 96469 @ 2 @ 1
1.1 Validity of this Documentation
Pos: 10 /Serie 750 (W AGO-I/O-SYSTEM)/Hinweise zur Dokumentation/ Gültigkeitsber eich/Gültigkeit sbereich Dokumentati on I/O-Modul 750-xxxx, ohne V ariantenangabe @ 14\mod_13589 44037947_21.doc x@ 1093 46@ @ 1
This documentation is only applicable to the I/O module 753-1630
(SMI Master Module 230 V AC).
Pos: 11 /Serie 750 (W AGO-I/O-SYSTEM)/Hinweise zur Dokumentation/ Hinweise/Achtung: Hinweiszur Doku mentation I/O-Module 750-xxxx @ 4\mod_ 1237986979656_21.doc x @ 29023 @ @ 1
The I/O module 753-1630 shall only be installed and operated according to the
instructions in this manual and in the manual for the used fieldbus
coupler/controller.
Consider power layout of the WAGO-I/O-SYSTEM 750!
In addition to these operating instructions, you will also need the manual for the
used fieldbus coupler/controller, which can be downloaded at www.wago.com.
There, you can obtain important information including information on electrical
isolation, system power and supply specifications.
Pos:12.1 /Alle Ser ien (Allgemeine Modu le)/Überschri ften/Ebene 2/Urheberschu tz - Überschrift 2 @ 23\mod_1435647042188_21. docx @ 184808 @ 2 @ 1
1.2 Copyright
Pos: 12.2 /Alle Serien ( Allgemeine Module)/ Rechtliches, Allge meines/Urheberschut z ausführlich @ 4\mod_1235565 145234_21.doc x@ 27691 @ @ 1
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.
Pos: 12.3 /Dokumentati on allgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_1221108045078 _0.docx @ 21810 @ @1

6 Notes about this Documentation
753-1630 SMI Master Module 230 V AC
Manual
Version 1.2.0 FW/HW Version 02/01
Pos: 12.4 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 2/ Symbole - Überschrif t 2 @ 13\mod_1351068042408_21. docx @ 105270 @ 2 @ 1
1.3 Symbols
Pos: 12.5.1 /Alle Serien ( Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/Gefahr /Gefahr: _Warnung vor Per sonenschäden allgem ein_ - Erläuterung @ 13\mod_1343 309450020_21.docx @ 101029 @ @ 1
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos:12.5.2 / AlleS erien (Allgemeine M odule)/Sicherhei ts- und sonstige Hinweise/ Gefahr/Gefahr: _W arnung vor Personenschäde n durch elektrischen Str om_ - Erläuterung @ 13\mod_13433 09694914_21.docx @ 101030 @ @ 1
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos:12.5.3 / AlleS erien (Allgemeine M odule)/Sicherhei ts- und sonstige Hinweise/ Warnung/Warnung: _Warnung vor Personensc häden allgemein_ - Erläut erung @ 13\mod_1343309877041 _21.docx @ 101035 @ @1
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Pos:12.5.4 / AlleS erien (Allgemeine M odule)/Sicherhei ts- und sonstige Hinweise/ Vorsicht/Vorsic ht: _Warnung vor Personen schäden allgemein_ - Erläuter ung @ 13\mod_1343310028762_2 1.docx @ 101038 @ @1
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Pos:12.5.5 / AlleS erien (Allgemeine M odule)/Sicherhei ts- und sonstige Hinweise/ Achtung/Achtung: _W arnung vor Sachschäden allg emein_ - Erläuterung @ 13\mod_ 1343310134623_21.doc x@ 101 041 @ @1
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos:12.5.6 / AlleS erien (Allgemeine M odule)/Sicherhei ts- und sonstige Hinweise/ Achtung/Achtung: _W arnung vor Sachschäden dur ch elektrostatisc he Aufladung_ - Erläuterung @ 13\mod_134 3310227702_21.doc x @ 101044 @ @ 1
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos:12.5.7 / AlleS erien (Allgemeine M odule)/Sicherhei ts- und sonstige Hinweise/ Hinweis/Hinweis: _Wichtiger Hinweis allgemein_ - Erläuter ung @ 13\mod_1343310326906_21. docx @ 101047 @ @1
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.
Pos:12.5.8 / AlleS erien (Allgemeine M odule)/Sicherhei ts- und sonstige Hinweise/ Information/Inf ormation: _Weiter e Information allgemein_ -Erläuterung @ 13\mod_1 343310439814_21.doc x@ 1010 51 @ @1

Notes about this Documentation 7
753-1630 SMI Master Module 230 V AC
Manual
Version 1.2.0 FW/HW Version 02/01
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).
Pos:12.6 /Dokum entation allgemein/ Gliederungselemen te/---Seitenwechsel--- @ 3\mod_12211 08045078_0.doc x@ 21810 @ @ 1

8 Notes about this Documentation
753-1630 SMI Master Module 230 V AC
Manual
Version 1.2.0 FW/HW Version 02/01
Pos: 12.7 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 2/ Darstellung der Zahlensysteme - Übersc hrift 2 @ 23\mod_1435647128 078_21.docx @ 184811 @ 2 @ 1
1.4 Number Notation
Pos: 12.8 /Alle Serien ( Allgemeine Module)/ Rechtliches, Allge meines/Zahlensyste me@ 3\mo d_1221059454015 _21.docx @ 2171 1 @ @1
Table 1: Number Notation
Number Code
Example
Note
Decimal
100
Normal notation
Hexadecimal
0x64
C notation
Binary
'100'
'0110.0100'
In quotation marks, nibble separated
with dots (.)
Pos: 12.9 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 2/ Schriftkonventio nen - Überschrift 2 @23\mod_1435647186005_ 21.docx @ 184814 @ 2 @ 1
1.5 Font Conventions
Pos: 12.10 /Alle Seri en (Allgemeine Module)/ Rechtliches, Allge meines/Schrif tkonventionen @ 3\mod_1221059521 437_21.docx @ 21714 @ @ 1
Table 2: Font Conventions
Font Type
Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Program Files\WAGO Software
Menu
Menu items are marked in bold letters.
e.g.: Save
>
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.: File > New
Input
Designation of input or optional fields are marked in bold letters,
e.g.:
Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under Start of measurement range.
[Button]
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key]
Keys are marked with bold letters in square brackets.
e.g.: [F5]
Pos: 13 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804507 8_0.docx @ 21810 @ @1

Important Notes 9
753-1630 SMI Master Module 230 V AC
Manual
Version 1.2.0 FW/HW Version 02/01
Pos: 14 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 1/W ichtige Erläuterun gen - Überschrift 1 @ 4\mod_1241428899156_21. docx @ 32170 @ 1 @ 1
2 Important Notes
Pos: 15.1 /Alle Serien ( Allgemeine Module)/ Rechtliches, Allge meines/Wichtige Er läuterungen - Einleitung @ 3\mod_1 221059818031_21.doc x@ 21717 @ @ 1
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
Pos: 15.2 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 2/ Rechtliche Grundl agen - Überschrift 2 @ 3\mod_1221060626343_21. docx @ 21726 @ 2 @ 1
2.1 Legal Bases
Pos: 15.3 /Alle Serien ( Allgemeine Module)/ Rechtliches, Allge meines/Änderungsvorbe halt - Überschri ft 3 und Inhalt @ 3\mod_1221 060036484_21.doc x@ 21720 @ 3 @ 1
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications. WAGO Kontakttechnik GmbH & Co. KG owns all
rights arising from the granting of patents or from the legal protection of utility
patents. Third-party products are always mentioned without any reference to
patent rights. Thus, the existence of such rights cannot be excluded.
Pos: 15.4 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterungen/Per sonalqualifikati on/Personalqua lifikation 750-xxxx - Übersc hrift 3 und Inhal t @ 3\mod_1224061208046_2 1.docx @ 24063 @ 3 @ 1
2.1.2 Personnel Qualifications
All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be
carried out by electrical specialists with sufficient knowledge in automation. The
specialists must be familiar with the current norms and guidelines for the devices
and automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
Pos: 15.5 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Bestimmungsgem äße Verwendung/Besti mmungsgemäße Verwendun g 750-xxxx- Über schrift 3 und I nhalt @ 3\mod_12240641512 34_21.docx @ 24070 @ 3 @ 1
2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with
Underlying Provisions
Fieldbus couplers, fieldbus controllers and I/O modules found in the modular
WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and
transmit them to actuators or higher-level control systems. Using programmable
controllers, the signals can also be (pre-) processed.
The devices have been developed for use in an environment that meets the IP20
protection class criteria. Protection against finger injury and solid impurities up to
12.5 mm diameter is assured; protection against water damage is not ensured.
Unless otherwise specified, operation of the devices in wet and dusty
environments is prohibited.
Operating the WAGO-I/O-SYSTEM 750 devices in home applications without
further measures is only permitted if they meet the emission limits (emissions of
interference) according to EN 61000-6-3. You will find the relevant information in
the section “Device Description” > “Standards and Guidelines” in the manual for
the used fieldbus coupler/controller.

10 Important Notes
753-1630 SMI Master Module 230 V AC
Manual
Version 1.2.0 FW/HW Version 02/01
Appropriate housing (per 2014/34/EU) is required when operating the
WAGO-I/O-SYSTEM 750 in hazardous environments. Please note that a
prototype test certificate must be obtained that confirms the correct installation of
the system in a housing or switch cabinet.
The implementation of safety functions such as EMERGENCY STOP or safety
door monitoring must only be performed by the F-I/O modules within the modular
WAGO-I/O-SYSTEM 750. Only these safe F-I/O modules ensure functional
safety in accordance with the latest international standards. WAGO's
interference-free output modules can be controlled by the safety function.
Pos: 15.6 /Alle Serien ( Allgemeine Module)/ Rechtliches, Allge meines/Technischer Zustand der Geräte - Über schrift 3 und I nhalt@ 3\mod_1221060446109 _21.docx @ 21723 @ 3 @ 1
2.1.4 Technical Condition of Specified Devices
The devices to be supplied ex works are equipped with hardware and software
configurations, which meet the individual application requirements. These
modules contain no parts that can be serviced or repaired by the user. The
following actions will result in the exclusion of liability on the part of WAGO
Kontakttechnik GmbH & Co. KG:
• Repairs,
• Changes to the hardware or software that are not described in the
operating instructions,
• Improper use of the components.
Further details are given in the contractual agreements. Please send your
request for modified and new hardware or software configurations directly to
WAGO Kontakttechnik GmbH & Co. KG.
Pos: 15.7 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 4/ Entsorgen - Überschri ft 4 @ 30\mod_151014511565 2_21.docx @ 469859 @ 4 @ 1
2.1.4.1 Disposal
Pos: 15.8 /Alle Serien ( Allgemeine Module)/ Rechtliches, Allge meines/Entsorgung @ 30\mod_151 0059393844_21.doc x @ 469714 @ @1
Recycle metals, plastics and packaging materials.
Automation components used in the professional sector (B2B) must be properly
disposed of once no longer in use in accordance with the respective national
guidelines (e.g., European Community Directive WEEE 2012/19/EU).
Packaging of all types must be disposed of in such a way that a high level of
recovery, reuse and recycling is possible. PPWD 94/62/EU and 2004/12/EU
packaging guidelines apply throughout Europe.
Pos: 15.9 /Dokumenta tion allgemein/Glied erungselemente/ ---Seitenwechsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

Important Notes 11
753-1630 SMI Master Module 230 V AC
Manual
Version 1.2.0 FW/HW Version 02/01
Pos: 15.10 /Alle Seri en (Allgemeine Module)/ Überschriften/Eben e 2/Sicherheitshi nweise - Überschrif t 2 @ 6\mod_1260180299987_21. docx @ 46724 @ 2 @ 1
2.2 Safety Advice (Precautions)
Pos: 15.11 /Alle Seri en (Allgemeine Module)/ Sicherheits- und sons tige Hinweise/Einlei tung Sicherheitshin weise Hardware @ 6\mod_126018017 0493_21.docx @ 46720 @ @ 1
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Pos: 15.12.1 /Alle Ser ien (Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/Gefahr /Gefahr: Nicht an Gerä tenu nter Spannung arbei ten! @ 6\mod_1260180365327 _21.docx @ 46727 @ @1
Do not work on devices while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Pos:15.12.2 / Serie 750 (WAGO-I/O-SYSTEM)/Wichti ge Erläuterungen/Sicher heits- und sonstige Hin weise/Gefahr/Gefahr : Einbau 0750-xxxx nur in Gehäuse n, Schränken oder elektri schen Betriebsräu men! @ 6\mod_1260180556692_ 21.docx @ 46731 @ @1
Install the device only in appropriate housings, cabinets or in electrical
operation rooms!
The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,
install the system and its components exclusively in appropriate housings,
cabinets or in electrical operation rooms. Allow access to such equipment and
fixtures to authorized, qualified staff only by means of specific keys or tools.
Pos:15.12.3 / Alle Serien (Allgemeine Module)/Sicherheits- und sonstige Hin weise/Gefahr/Gefa hr: Unfallverhütungs vorschriften beac hten! @ 6\mod_126018065700 0_21.docx @ 46735 @ @1
Pos:15.12.4 / Alle Serien (Allgemeine Module)/Sicherheits- und sonstige Hin weise/Gefahr/Gefa hr: Auf normgerechten Ansc hluss achten! @ 6\mod_1 260180753479_21.doc x@ 467 39 @ @ 1
Pos: 15.13.1 /Alle Ser ien (Allgemeine Module) /Sicherheits- und sonsti ge Hinweise/Achtun g/Achtung: Defekte od er beschädigte Geräte au stauschen! @ 6\mod_12601 80857358_21.docx @ 46743 @ @ 1
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts), since the long-term functionality of device/module involved can no
longer be ensured.
Pos:15.13.2 / Alle Serien (Allgemeine Module)/Sicherheits- und sonstige Hin weise/Achtung/Ac htung: Geräte vor kri echenden und isolierenden Stof fen schützen! @ 6\mod_1 260181036216_21.doc x@ 4674 7 @ @ 1
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for
handling devices/modules.
Pos:15.13.3 / Alle Serien (Allgemeine Module)/Sicherheits- und sonstige Hin weise/Achtung/Ac htung: Reinigung nur mit z ulässigen Materiali en! @ 6\mod_1260181203293_2 1.docx @ 46751 @ @1
Clean only with permitted materials!
Clean housing and soiled contacts with propanol.
Pos:15.13.4 / Alle Serien (Allgemeine Module)/Sicherheits- und sonstige Hin weise/Achtung/Ac htung: Kein Kontaktspr ay verwenden! @ 6\mod_126018 1290808_21.docx @ 46755 @ @ 1

12 Important Notes
753-1630 SMI Master Module 230 V AC
Manual
Version 1.2.0 FW/HW Version 02/01
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
Pos:15.13.5 / Alle Serien (Allgemeine Module)/Sicherheits- und sonstige Hin weise/Achtung/Ac htung: Verpolungen der Da ten- und Versorgungsleit ungen vermeiden! @ 6\mod _1260184045 744_21.docx @ 46767 @ @1
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Pos:15.13.6 / Alle Serien (Allgemeine Module)/Sicherheits- und sonstige Hin weise/Achtung/Ac htung: Elektrostati sche Entladung vermeide n! @ 6\mod_1260181364729_21. docx @ 46759 @ @1
Avoid electrostatic discharge!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge when touched. Please observe the safety precautions
against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the
devices, please ensure that environmental factors (personnel, work space and
packaging) are properly grounded.
Pos:16 /Doku mentation allgemein/Gli ederungselemen te/---Seitenwechsel--- @ 3\mod_12211 08045078_0.docx @ 21810 @ @ 1

Device Description 13
753-1630 SMI Master Module 230 V AC
Manual
Version 1.2.0 FW/HW Version 02/01
Pos: 17 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 1/ Gerätebeschreibung - Übersc hrift 1 @ 3\mod_12337 56084656_21.doc x@ 27096@ 1 @ 1
3 Device Description
Pos: 18 /Serie 753 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/Ei nleitung/753-1630/ Anwendung 753-1630 @ 27\mod_14 71860125822_21.doc x@ 21869 2 @ @1
The SMI master module is used to control Standard Motor Interface (SMI) drives
indoors and outdoors, e.g., for blinds, and is used specifically in building
automation.
The SMI master module 753-1630 can operate up to 16 SMI drives via the SMI
interface on a 750 Series WAGO fieldbus node. The SMI master module is
designed for SMI drives that operate at a supply voltage of 110 V to 240 VAC.
The SMI master module has a DC input acc. IEC 61131-2, Type 1. When setting
the parameters, the input can be assigned a specific function, e.g., triggering
travel commands via an external button (1-button operation) or moving to a
forced position.
The SMI master module has a short-circuit-protected 24 VDC output acc.
IEC 61131-2 with a rated current of 0.5 A. The output is used to control shutdown
logic for energy saver mode. The load to be switched must be connected to the
0V potential of the field supply.
Assigning the connections is described in the “Connections” section.
Connection examples are given in the section “Connecting Devices” > … >
“Connection Examples”.
The 753-1630 SMI master module receives the 24 V power supply and 0 V
potential for the field level from an upstream I/O module or fieldbus
coupler/controller via the power contacts used as blade contacts. It then provides
this potential to subsequent I/O modules.
The 24 VDC required for operating SMI drives is not supplied by the SMI master
module, but must be executed separately.
A green status LED indicates the operating status and error-free I/O module
communication.
Red error LEDs display the status of the field-side power supply and the
presence of a general error.
Other LEDs provide information on diagnostic states.
The meaning of the LEDs is described in section “Display Elements”.
An IEC 61131-3 function block library and “WAGO SMI Configurator” software
are available for commissioning, configuration and maintenance of the SMI
master module and attached SMI drives.
Shading applications can be implemented with the IEC 61131-3 function block
library.
Pos: 19 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804507 8_0.docx @ 21810 @ @1

14 Device Description
753-1630 SMI Master Module 230 V AC
Manual
Version 1.2.0 FW/HW Version 02/01
Pos: 20 /Serie 753 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/Ei nleitung/Einsa tzbereich/Kompatibi litätsliste 0753-16 30/-1631 - Full-Modus @ 29\mod_1495184 962145_21.doc x@ 422218 @ @ 1
The 753-1630 I/O module can be operated in Full mode on the following fieldbus
couplers/controllers of the WAGO-I/O-SYSTEM 750 from the specified revision
level:
Table 3: Compatibility List 753-1630 – Full Mode
Bus System Fieldbus Coupler/Controller Item No.
Firmware Revision
Status
ETHERNET
Controller
750-852
09
750-880
09
750-881
09
750-882
09
750-885
09
PFC100 Controller
750-8100
09
750-8101
09
750-8102
09
PFC200 Controller
750-8202
08
750-8203
08
750-8204
08
750-8206
08
750-8207
08
750-8208
09
BA application controller
750-884
09
I/O-IPC
758-874/000-xxx
09
758-875/000-xxx
09
758-876/000-xxx
09
BACnet Controller
750-829
07
750-831
07
KNX
Controller
750-889
07
Pos: 21 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_1221108045078_0. docx @ 21810 @ @1

Device Description 15
753-1630 SMI Master Module 230 V AC
Manual
Version 1.2.0 FW/HW Version 02/01
Pos: 22 /Serie 753 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/Ei nleitung/Einsa tzbereich/Kompatibi litätsliste 0753-16 30/-1631 - Feldbuskoppler modus @ 28\mod_147931992730 5_21.docx @ 387438 @ @1
The 753-1630 I/O module can be operated in Fieldbus Coupler mode on the
following fieldbus couplers/controllers of the WAGO-I/O-SYSTEM 750 from the
specified revision level:
Table 4: Compatibility List 753-1630 – Fieldbus Coupler Mode
Bus System Fieldbus Coupler/Controller Item No.
Firmware Revision
Status
PROFINET Fieldbus coupler
750-370
09
750-375
05
750-377
05
PROFIBUS
Fieldbus coupler
750-333
19
Controller
750-833
18
Ethernet
Fieldbus coupler
750-342
18
750-352
09
Controller
750-841
21
750-842
19
750-843
03
750-852
09
750-871
09
750-872
05
750-873
05
750-880
09
750-881
09
750-882
09
750-885
09
PFC100 controller
750-810x
09
Controller PFC200
750-820x
08
BA application controller
750-884
09
I/O-IPC
758-874/000-xxx
09
758-875/000-xxx
09
758-876/000-xxx
09
DeviceNet
Fieldbus coupler
750-306
4L
ECO fieldbus coupler
750-346
11
Controller
750-806
11
CANopen
Fieldbus coupler
750-337
21
750-338
21
ECO fieldbus coupler
750-347
11
750-348
11
Controller
750-837
17
750-838
17
MODBUS
Fieldbus coupler
750-315/300-000
01
750-316/300-000
01
Controller
750-815/300-000
01
750-816/300-000
01
EtherCAT
Fieldbus coupler
750-354
03
BACnet Controller
750-829
07
750-830
05
750-831
07
KNX Controller
750-849
05
750-889
07
Pos: 23 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804507 8_0.docx @ 21810 @ @1

16 Device Description
753-1630 SMI Master Module 230 V AC
Manual
Version 1.2.0 FW/HW Version 02/01
Pos: 24 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 2/An sicht - Überschrif t 2 @ 4\mod_1240984217343_21. docx @ 31958 @ 2 @ 1
3.1 View
Pos: 25 /Serie 753 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/Ansi cht/FT&K/Ansic ht 753-1630 @ 27\mod_147186088 7695_21.docx @ 218747 @ @ 1
Figure 1: View of Device
Pos: 26 /Serie 753 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/Ansi cht/Ansicht – Lege nde mit Leistungskont akten_mit Kodierung, Kabelbefestigung und Prüföff nungen @ 20\mod_1411031302199_21. docx @ 163871 @ @1
Table 5: Legend for Figure “View”
Pos.
Description
Details See Section
1
Marking possibility with Mini-
WSB
---
2
Status-LEDs
“Device Description” > “Display
Elements”
3
Data contacts
“Device Description” > “Connectors”
4
CAGE CLAMP®connectors
“Device Description” > “Connectors”
5
Pull tab
“Mounting” > “I/O Modules with
Pluggable Wiring Level (Series 753)”
6
Coding possibility with coding
fingers
“Mounting” > “Coding”
7
Power jumper contacts
“Device Description” > “Connectors”
8
Test port
---
9
Fixing lug for cable ties
“Mounting” > “I/O Modules with
Pluggable Wiring Level (Series 753)”
Pos: 27 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_1221108045078_0. docx @ 21810 @ @1

Device Description 17
753-1630 SMI Master Module 230 V AC
Manual
Version 1.2.0 FW/HW Version 02/01
Pos: 28 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 2/An schlüsse - Überschr ift 2 @ 4\mod_1240984262656_2 1.docx @ 31961 @ 2 @ 1
3.2 Connectors
Pos: 29 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/Ansc hlüsse/Datenkon takte/Lokalbus - Übersc hrift 3 @ 6\mod_1256294684 083_21.docx @ 43660 @ 3 @ 1
3.2.1 Data Contacts/Local Bus
Pos: 30.1 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Anschlüsse/Datenk ontakte - Feldbuskoppler/ -controller, Abbi ldung und Beschreibung @ 3\mod_123 1771259187_21.doc x @ 26002@ @ 1
Communication between the fieldbus coupler/controller and the I/O modules as
well as the system supply of the I/O modules is carried out via the local bus. It is
comprised of 6 data contacts, which are available as self-cleaning gold spring
contacts.
Figure 2: Data Contacts
Pos: 30.2 /Serie 750 ( WAGO-I/O-SYSTEM)/Wic htige Erläuterungen/Sic herheits- und sonstige Hinweise/Achtung/ Achtung: I/O-Modul e nicht auf Goldfeder kontakte legen! @7\mod_126631846363 6_21.docx @ 50695 @ @1
Do not place the I/O modules on the gold spring contacts!
Do not place the I/O modules on the gold spring contacts in order to avoid soiling
or scratching!
Pos:30.3 /Ser ie 750 (WAGO-I/O-SYSTEM)/Wichtige Er läuterungen/Sicherhei ts- und sonstige Hinweise/ Achtung/Achtung: ESD- Auf gute Erdung der U mgebung achten! @ 7\mod_126631 8538667_21.docx @ 50708 @ @ 1
Ensure that the environment is well grounded!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge. When handling the devices, ensure that the environment
(persons, workplace and packing) is well grounded. Avoid touching conductive
components, e.g. data contacts.
Pos:31 /Doku mentation allgemein/Gli ederungselemen te/---Seitenwechsel--- @ 3\mod_12211 08045078_0.docx @ 21810 @ @ 1

18 Device Description
753-1630 SMI Master Module 230 V AC
Manual
Version 1.2.0 FW/HW Version 02/01
Pos: 32 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/Ansc hlüsse/Leistun gskontakte/Feldver sorgung - Überschrif t 3 @ 6\mod_1256294692864_21. docx @ 43664 @ 3 @ 1
3.2.2 Power Jumper Contacts/Field Supply
Pos: 33 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterungen/ Sicherheits- und sons tige Hinweise/Vorsic ht/Vorsicht: Verle tzungsgefahr dur ch scharfkantige Messerko ntakte! @ 6\mod_12561932794 01_21.docx @ 43414 @ @ 1
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury.
Pos:34 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Anschlüsse/Lei stungskontakte 2 LK ( Messer/Feder) - Einleitung @ 15\mod _1371721641099_21.doc x@ 123 714 @ @ 1
The I/O module 753-1630 has 2 self-cleaning power jumper contacts that supply
and transmit power for the field side. The contacts on the left side of the I/O
module are designed as blade contacts and those on the right side as spring
contacts.
Pos: 35 /Serie 753 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/Ansc hlüsse/Leistun gskontakte/Feld versorgung 2 LK (Messer/ Feder) - Abbildung @ 17\mod_13819 24880242_21.docx @ 134239 @ @ 1
Figure 3: Power Jumper Contacts
Pos: 36 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/Ansc hlüsse/Leistun gskontakte 2 LK (Messer/ Feder) - Legende @ 15\mod_137172135 2500_21.docx @ 123710 @ @ 1
Table 6: Legend for Figure “Power Jumper Contacts”
Contact
Type
Function
1
Spring contact
Potential transmission (Uv) for field supply
2
Spring contact
Potential transmission (0 V) for field supply
3
Blade contact
Potential feed-in (0 V) for field supply
4
Blade contact
Potential feed-in (Uv) for field supply
Pos: 37 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterungen/ Sicherheits- und sons tige Hinweise/Achtung/ Achtung: Maximaler Str om Leistungskontak te 10 A @ 3\mod_122649914350 0_21.docx @ 25029 @ @1
Do not exceed maximum current via power jumper contacts!
The maximum current to flow through the power jumper contacts is 10 A.
Greater currents can damage the contacts.
When configuring your system, ensure that this current is not exceeded.
If exceeded, insert an additional supply module.
Pos:38 /Doku mentation allgemein/Gli ederungselemen te/---Seitenwechsel--- @ 3\mod_12211 08045078_0.docx @ 21810 @ @ 1

Device Description 19
753-1630 SMI Master Module 230 V AC
Manual
Version 1.2.0 FW/HW Version 02/01
Pos: 39 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/Ansc hlüsse/CAGE CLAMP-Ansc hlüsse - Überschrift 3 @6\mod_1256296337770 _21.docx @ 43674 @ 3 @ 1
3.2.3 CAGE CLAMP®Connectors
Pos: 40 /Serie 753 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/Ansc hlüsse/FT&K/An schlüsse 753-1630, -1631 @ 27\mod_147186134426 0_21.docx @ 218751 @ @1
Figure 4: CAGE CLAMP®Connections
Pos: 41 /Serie 753 (W AGO-I/O-SYSTEM)/Wichtige Erläuterungen/ Sicherheits- und sons tige Hinweise/War nung: SMI-Master -Modul über Kommuni kationsleitungen ni cht mit 230 V belasten @ 31\mod_ 1518087247517_21.doc x@ 475 836 @ @ 1
Do not load the SMI master module with 230 V via communication lines
The communication lines I+ und I− of the SMI bus must not be supplied with
230 V if the SMI master module is connected.
Pos:42 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Anschlüsse/Fun ktionserde - Überschr ift 3 @ 21\mod_14188973829 94_21.docx @ 170638 @ 3 @ 1
3.2.4 Function Earth
Pos: 43 /Serie 750 (W AGO-I/O-SYSTEM)/Geräteb eschreibung/Ansch lüsse/Funktionser dung FE @ 21\mod_1418897657 338_21.docx @ 170642 @ @1
In order to get a function earth, a connection to the mounting rail is made via a
spring contact. If the rail is correctly connected to PE, the immunity to
interference is increased.
Pos: 44 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804507 8_0.docx @ 21810 @ @1
Table 7: Legend for “CAGE CLAMP®Connections” Figure
Connection
Function
DI Digital input
DO
Digital Output
24 V
Field supply 24 VDC tap
0 V
0 V field supply potential tap
I+
SMI communication cable I+
I−
SMI communication cable I−

20 Device Description
753-1630 SMI Master Module 230 V AC
Manual
Version 1.2.0 FW/HW Version 02/01
Pos: 45 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 2/An zeigeelemente - Übersc hrift 2 @ 4\mod_1240984390 875_21.docx @ 31964 @ 2 @ 1
3.3 Display Elements
Pos: 46 /Serie 753 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/Anz eigeelemente/F T&K/Anzeigeelemente 75 3-1630, -1631 @ 27\mod_147186742509 3_21.docx @ 218755 @ @1
Figure 5: Display Elements
Table 8: Legend for the “Display Elements” Figure
LED Designation
Conditio
n
Function
A Local bus status
Off
Local bus failure:
Not ready for operation or no/faulty
local bus communication
Green
Ready for operation and uninterrupted
local bus communication
B
Undervoltage field
supply / SMI
connection short
circuit
Off
Power supply is sufficient.
Red
Supply voltage is below the required
minimum voltage.
Blinking
Short circuit of connections I+ and I−
C TxD
(data transmission)
Off
No SMI telegram is being sent
currently.
Green
SMI telegram was just sent.
D Digital input
Off
In Low status
Green
In High status
E General error
Off
No error detected.
Red
Controller failure or local bus failure
was detected.
F Operating mode
Off
Normal operation active
Yellow
Energy saving mode active
Blinking
Forced position triggered due to one of
the following events:
- Controller failure
- Local bus failure
- Safety-related signal at the digital
input
G RxD
(data receipt)
Off
No SMI telegram is being received
currently.
Green
SMI telegram was just received.
H Digital output
Off
In Low status
Green
In High status
Pos: 47 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804507 8_0.docx @ 21810 @ @1